3D numerical modeling and experimental validation of diamagnetic levitated suspension in the static field

Diamagnetic levitation principle opens to promising solutions for innovative powerless and low stiffness suspension applicable to many technological fields. The peculiarities of diamagnetic suspension make this design solution very attractive for some applications such as microdevices and energy harvesters. Low stiffness and powerless functioning are the most appreciable characteristics of this kind of suspension, despite their force-displacement curve is generally hard to predict and strongly nonlinear. The modeling complexity resides in the preliminary prediction of magnetic field distribution and in the calculation of diamagnetic forces as function of the levitation height. This work introduces a modeling approach for calculating the levitation height of a parameterized diamagnetic suspension composed of a ground of permanent magnets and a levitating mass made of pyrolytic graphite. The numerical discretization approach is used and the predicted values are compared with experiments providing good agreement between result

Tribology of Microball Bearing MEMS

This dissertation explores the fundamental tribology of microfabricated rolling bearings for future micro-machines. It is hypothesized that adhesion, rather than elastic hysteresis, dominates the rolling friction and wear for these systems, a feature that is unique to the micro-scale. To test this hypothesis, specific studies in contact area and surface energy have been performed. Silicon microturbines supported on thrust bearings packed with 285 µm and 500 µm diameter stainless steel balls have undergone spin-down friction testing over a load and speed range of 10-100mN and 500-10,000 rpm, respectively. A positive correlation between calculated contact area and measured friction torque was observed, supporting the adhesion-dominated hysteresis hypothesis. Vapor phase lubrication has been integrated within the microturbine testing scheme in a controlled and characterized manner. Vapor-phase molecules allowed for specifically addressing adhesive energy without changing other system properties. A 61% reduction of friction torque was observed with the utilization of 18% relative humidity water vapor lubrication. Additionally, the relationship between friction torque and normal load was shown to follow an adhesion-based trend, highlighting the effect of adhesion and further confirming the adhesion-dominant hypothesis. The wear mechanisms have been studied for a microfabricated ball bearing platform that includes silicon and thin-film coated silicon raceway/steel ball materials systems. Adhesion of ball material, found to be the primary wear mechanism, is universally present in all tested materials systems. Volumetric adhesive wear rates are observed between 4x10^-4 µm^3/mN*rev and 4x10^-5 µm3/mN*rev were determined by surface mapping techniques and suggest a self-limiting process. This work also demonstrates the utilization of an Off-The-Shelf (OTS) MEMS accelerometer to confirm a hypothesized ball bearing instability regime which encouraged the design of new bearing geometries, as well as to perform in situ diagnostics of a high-performance rotary MEMS device. Finally, the development of a 3D fabrication technique with the potential of significantly improving the performance of micro-scale rotary structures is described. The process was used to create uniform, smooth, curved surfaces. Micro-scale ball bearings are then able to be utilized in high-speed regimes where load can be accommodated both axially and radially, allowing for new, high-speed applications. A comprehensive exploration of the fundamental tribology of microball bearing MEMS has been performed, including specific experiments on friction, wear, lubrication, dynamics, and geometrical optimization. Future devices utilizing microball bearings will be engineered and optimized based on the results of this dissertation

The 1991 Marshall Space Flight Center research and technology

A compilation of 194 articles addressing research and technology activities at the Marshall Space Flight Center (MSFC) is given. Activities are divided into three major areas: advanced studies addressing transportation systems, space systems, and space science activities conducted primarily in the Program Development Directorate; research tasks carried out in the Space Science Laboratory; and technology programs hosted by a wide array of organizations at the Center. The theme for this year's report is 'Building for the Future'

SEIS: Insight's Seismic Experiment for Internal Structure of Mars.

By the end of 2018, 42 years after the landing of the two Viking seismometers on Mars, InSight will deploy onto Mars' surface the SEIS (Seismic Experiment for Internal Structure) instrument; a six-axes seismometer equipped with both a long-period three-axes Very Broad Band (VBB) instrument and a three-axes short-period (SP) instrument. These six sensors will cover a broad range of the seismic bandwidth, from 0.01 Hz to 50 Hz, with possible extension to longer periods. Data will be transmitted in the form of three continuous VBB components at 2 sample per second (sps), an estimation of the short period energy content from the SP at 1 sps and a continuous compound VBB/SP vertical axis at 10 sps. The continuous streams will be augmented by requested event data with sample rates from 20 to 100 sps. SEIS will improve upon the existing resolution of Viking's Mars seismic monitoring by a factor of ∼ 2500 at 1 Hz and ∼ 200 000 at 0.1 Hz. An additional major improvement is that, contrary to Viking, the seismometers will be deployed via a robotic arm directly onto Mars' surface and will be protected against temperature and wind by highly efficient thermal and wind shielding. Based on existing knowledge of Mars, it is reasonable to infer a moment magnitude detection threshold of M w ∼ 3 at 40 ∘ epicentral distance and a potential to detect several tens of quakes and about five impacts per year. In this paper, we first describe the science goals of the experiment and the rationale used to define its requirements. We then provide a detailed description of the hardware, from the sensors to the deployment system and associated performance, including transfer functions of the seismic sensors and temperature sensors. We conclude by describing the experiment ground segment, including data processing services, outreach and education networks and provide a description of the format to be used for future data distribution.Electronic supplementary materialThe online version of this article (10.1007/s11214-018-0574-6) contains supplementary material, which is available to authorized users

Design and optimization of magnetostrictive actuator

Magnetostnctive ("MS') technology and Magneto-Rheologlcal Fluid ("MRF") technology are old "newcomers" coming to the market at high speed. Various industries including the automotive industry are full of potential MS and MRF applications. Magnetostrictive technology and Magneto-Rheological Fluid technology have been successfully employed in some low and high volume applications A structure based on "MSm-technology might be the next generation in design for products where power density, accuracy and dynamic performance are key features. Since the introduction of active (MS) materials such as Terfenol-D, \nth stable characteristics over a wide range of temperatures and high magnetoelastic properties, interest in MS technology has been growing. Additionally, for products where is a need to control fluid motion by varying the viscosity, a structure based on MRF might be an improvement in performance. Two aspects of this technology, direct shear mode (used in brakes and clutches) and valve mode (used in dampers) have been studied thoroughly and several applications are already present on the market. Excellent features like fast response, slmple interface between electrical input and hydraulic output make MRF technology attractive for many applications. This dissertation is the introduction of an actuator based on "MS"-technology The possible control arrangement is based on "MR"-technology. The thesis is submitted for the degree of the PhD The dissertation contains the layout definition, analytical calculations, simulations, and design verification and optimization with evaluation of experimental results for the actuator based on "MS"-technology in combination of a possible control device based on "MR"-technology

Magnetic Levitation of Polymeric Photo-thermal Microgrippers

Precise manipulation of micro objects became great interest in engineering and science with the advancements in microengineering and microfabrication. In this thesis, a magnetically levitated microgripper is presented for microhandling tasks. The use of magnetic levitation for positioning reveals the problems associated with modeling of complex surface forces and the use of jointed parts or wires. The power required for the levitation of the microgripper is generated by an external drive unit that makes further minimization of the gripper possible. The gripper is made of a biocompatible material and can be activated remotely. These key features make the microgripper a great candidate for manipulation of micro components and biomanipulation. In order to achieve magnetic levitation of microrobots, the magnetic field generated by the magnetic levitation setup is simulated. The magnetic flux density in the air gap region is improved by the integration of permanent magnets and an additional electromagnet to the magnetic loop assembly. The levitation performance is evaluated with millimeter size permanent magnets. An eddy current damping method is implemented and the levitation accuracy is doubled by reducing the positioning error to 20.3 µm. For a MEMS-compatible microrobot design, the electrodeposition of Co-Ni-Mn-P magnetic thin films is demonstrated. Magnetic films are deposited on silicon substrate to form the magnetic portion of the microrobot. The electrodeposited films are extensively characterized. The relationship between the deposition parameters and structural properties is discussed leading to an understanding of the effect of deposition parameters on the magnetic properties. It is shown that both in-plane and out-of-plane magnetized films can be obtained using electrodeposition with slightly differentiated deposition parameters. The levitation of the electrodeposited magnetic samples shows a great promise toward the fabrication of levitating MEMS devices. The end-effector tool of the levitating microrobot is selected as a microgripper that can achieve various manipulation operations such as pulling, pushing, tapping, grasping and repositioning. The microgripper is designed based on a bent-beam actuation technique. The motion of the gripper fingers is achieved by thermal expansion through laser heat absorption. This technique provided non-contact actuation for the levitating microgripper. The analytical model of the displacement of the bent-beam actuator is developed. Different designs of microgripper are fabricated and thoroughly characterized experimentally and numerically. The two microgripper designs that lead to the maximum gripper deflection are adapted for the levitating microrobot. The experimental results show that the levitating microrobot can be positioned in a volume of 3 x 3 x 2 cm^3. The positioning error is measured as 34.3 µm and 13.2 µm when electrodeposited magnets and commercial permanent magnets are used, respectively. The gripper fingers are successfully operated on-the-fly by aligning a visible wavelength laser beam on the gripper. Micromanipulation of 100 µm diameter electrical wire, 125 µm diameter optical fiber and 1 mm diameter cable strip is demonstrated. The microgripper is also positioned in a closed chamber without sacrificing the positioning accuracy

Proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress

Published proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress, hosted by York University, 27-30 May 2018

Advanced Energy Harvesting Technologies

Energy harvesting is the conversion of unused or wasted energy in the ambient environment into useful electrical energy. It can be used to power small electronic systems such as wireless sensors and is beginning to enable the widespread and maintenance-free deployment of Internet of Things (IoT) technology. This Special Issue is a collection of the latest developments in both fundamental research and system-level integration. This Special Issue features two review papers, covering two of the hottest research topics in the area of energy harvesting: 3D-printed energy harvesting and triboelectric nanogenerators (TENGs). These papers provide a comprehensive survey of their respective research area, highlight the advantages of the technologies and point out challenges in future development. They are must-read papers for those who are active in these areas. This Special Issue also includes ten research papers covering a wide range of energy-harvesting techniques, including electromagnetic and piezoelectric wideband vibration, wind, current-carrying conductors, thermoelectric and solar energy harvesting, etc. Not only are the foundations of these novel energy-harvesting techniques investigated, but the numerical models, power-conditioning circuitry and real-world applications of these novel energy harvesting techniques are also presented