Sensorless Control of Switched-Flux Permanent Magnet Machines

This thesis investigates the sensorless control strategies of permanent magnet synchronous machines (PMSMs), with particular reference to switched-flux permanent magnet (SFPM) machines, based on high-frequency signal injection methods for low speed and standstill and the back-EMF based methods for medium and high speeds

Sensorless position estimation in fault-tolerant permanent magnet AC motor drives with redundancy.

Safety critical applications are heavily dependent on fault-tolerant motor drives being capable of continuing to operate satisfactorily under faults. This research utilizes a fault-tolerant PMAC motor drive with redundancy involving dual drives to provide parallel redundancy where each drive has electrically, magnetically, thermally and physically independent phases to improve its fault-tolerant capabilities. PMAC motor drives can offer high power and torque densities which are essential in high performance applications, for example, more-electric airplanes. In this thesis, two sensorless algorithms are proposed to estimate the rotor position in a fault-tolerant three-phase surface-mounted sinusoidal PMAC motor drive with redundancy under normal and faulted operating conditions. The key aims are to improve the reliability by eliminating the use of a position sensor which is one of major sources of failures, as well as by offering fault-tolerant position estimation. The algorithms utilize measurements of the winding currents and phase voltages, to compute flux linkage increments without integration, hence producing the predicted position values. Estimation errors due measurements are compensated for by a modified phase-locked loop technique which forces the predicted positions to track the flux linkage increments, finally generating the rotor position estimate. The fault-tolerant three-phase sensorless position estimation method utilizes the measured data from the three phase windings in each drive, consequently obtaining a total of two position estimates. However, the fault-tolerant two-phase sensorless position estimation method uses measurements from pairs of phases and produces three position estimates for each drive. Therefore, six position estimates are available in the dual drive system. In normal operation, all of these position estimates can be averaged to achieve a final rotor angle estimate in both schemes. Under faulted operating conditions, on the other hand, a final position estimate should be achieved by averaging position estimates obtained with measurements from healthy phases since unacceptable estimation errors can be created by making use of measured values from phases with failures. In order to validate the effectiveness of the proposed fault-tolerant sensorless position estimation schemes, the algorithms were tested using both simulated data and offline measured data from an experimental fault-tolerant PMAC motor drive system. In the healthy condition, both techniques presented good performance with acceptable accuracies under low and high steady-state speeds, starting from standstill and step load changes. In addition, they had robustness against parameter variations and measurement errors, as well as the ability to recover quickly from large incorrect initial position information. Under faulted operating conditions such as sensor failures, however, the two-phase sensorless method was more reliable than the threephase sensorless method since it could operate even with a faulty phase.Thesis (Ph.D.) -- University of Adelaide, School of Electrical and Electronic Engineering, 201

Comparison of two novel MRAS strategies for identifying parameters in permanent magnet synchronous motors

Two Model Reference Adaptive System (MRAS) estimators are developed for identifying the parameters of permanent magnet synchronous motors (PMSM) based on Lyapunov stability theorem and Popov stability criterion, respectively. The proposed estimators only need online detection of currents, voltages and rotor rotation speed, and are effective in the estimation of stator resistance, inductance and rotor flux-linkage simultaneously. Their performances are compared and verified through simulations and experiments. It shows that the two estimators are simple and have good robustness against parameter variation and are accurate in parameter tracking. However, the estimator based on Popov stability criterion, which can overcome the parameter variation in a practical system, is superior in terms of response speed and convergence speed since there are both proportional and integral units in the estimator in contrast to only one integral unit in the estimator based on Lyapunov stability theorem. In addition, there is no need of the expert experience which is required in designing a Lyapunov function

Rotor Position Identification for Brushless DC motor

Permanent magnet BLDC motors are characterized by a central magnetic core, called the rotor, and fixed electric coils (usually six) equally spaced in a ring around the core, called the stator. Motor movement is controlled by alternately energizing and de-energizing the stator coils to create a rotating magnetic field that propels the rotor. In order for this process to work correctly, BLDC motors required a technology called electronic commutation, in which the coil currents must be very carefully synchronized to rotor position to ensure that the rotating field is correctly aligned with the permanent magnetic field in the rotor. Usually rotor position is measured by external sensors such as Hall-effect sensors and optical encoders and these external sensors increase the system cost and reduces reliability. In order to control the price and make it more reliable this thesis propose to infer the rotor position from voltage and current measurement of motor. The most common approaches to sensorless control are based on the measurement of the electromotive force (back-EMF), that is induced by the rotor motion. As the back-EMF is nearly zero at very low speed and at stationary position, and can not be measured. Therefore a separate algorithm is required for start-up and control at low speed. The other method of sensorless control involves the inference of rotor position from the variation in inductance caused by rotor position. This thesis presents a prototype system for sensorless control of BLDC motors over the entire speed range of the motor, including stall (zero speed) conditions using the voltage and current signals from the motor

Parameter estimation for condition monitoring of PMSM stator winding and rotor permanent magnets

Winding resistance and rotor flux linkage are important to controller design and condition monitoring of a surface-mounted permanent-magnet synchronous machine (PMSM) system. In this paper, an online method for simultaneously estimating the winding resistance and rotor flux linkage of a PMSM is proposed, which is suitable for application under constant load torque. It is based on a proposed full-rank reference/variable model. Under constant load torque, a short pulse of id 0 is transiently injected into the d-axis current, and two sets of machine rotor speeds, currents, and voltages corresponding to id = 0 and id 0 are then measured for estimation. Since the torque is kept almost constant during the transient injection, owing to the moment of system inertia and negligible reluctance torque, the variation of rotor flux linkage due to injected id 0 can be taken into account by using the equation of constant torque without measuring the load torque and is then associated with the two sets of machine equations for simultaneously estimating the winding resistance and rotor flux linkage. Furthermore, the proposed method does not need the values of the $dq$-axis inductances, while the influence from the nonideal voltage measurement, which will cause an ill-conditioned problem in the estimation, has been taken into account and solved by error analysis. This method is finally verified on two prototype PMSMs and shows good performance. © 1982-2012 IEEE

Influence of nonideal voltage measurement on parameter estimation in permanent-magnet synchronous machines

This paper investigates the influence of nonideal voltage measurements on the parameter estimation of permanentmagnet synchronous machines (PMSMs). The influence of nonideal voltage measurements, such as the dc bus voltage drop, zero shift in the amplifier, and voltage source inverter nonlinearities, on the estimation of different machine parameters is investigated by theoretical and experimental analysis. For analysis, a model-reference-adaptive-system-based estimator is first described for the parameter estimation of the q-axis inductance, stator winding resistance, and rotor flux linkage. The estimator is then applied to a prototype surface-mounted PMSM to investigate the influence of nonideal voltage measurement on the estimation of various machine parameter values. It shows that, at low speed, the inverter nonlinearity compensation has significant influence on both the rotor flux linkage and winding resistance estimations while, at high speed, it has significant influence only on the winding resistance estimation and has negligible influence on the rotor flux linkage estimation. In addition, the inverter nonlinearity compensation will not influence the q-axis inductance estimation when it is under id = 0 control. However, the dc bus voltage drop due to the load variation and zero shift in the amplifier will significantly influence the q-axis inductance estimation. © 2011 IEEE

Control of a brushless permanent magnet machine using an integrated torque sensor in place of a rotor position sensor

The work presented in this thesis proposes the use of measured torque feedback from an integrated, low cost surface acoustic wave (SAW) torque transducer in place of a position sensor to control brushless permanent magnet (BLPM) machines. The BLPM machine closed loop control requires knowledge of the rotor position to control stator current and maximum torque per ampere. The electrical position feedback to control the phase current requires a position sensor or position sensorless technique. Position sensors such as absolute encoder or resolver are needed for position information, in the absolute encoder, an accurately patterned disk rotates between a light source and a detector giving a unique digital output signal for every shaft position. However, each bit in the digital world represents an independent track on the encoder disk, resulting in a complex and costly sensors. Brushless resolvers operation is based on inductive coupling between stator and rotor winding. The resolver with its resolver to digital converter also gives precise absolute position information, but again the cost is often prohibitive. So the disadvantages of the position sensors are the added cost and size to the machine. The position sensorless techniques for the BLPM machine are based on obtaining position from the terminal voltages and currents based on estimating the back electro-magnetic force (EMF), flux-linkage or inductance which from position can be estimated. The disadvantages of the back-EMF and flux-linkage techniques are (1) that they behave poorly at zero and low speed (2) behave poorly for load disturbances since load torque is estimated from machine parameters which can change. The inductance techniques work at zero and low speed, however the disadvantages are (1) in a surface mounted machine there is no saliency so any variation of winding inductances with rotor position arises from magnetic saturation; (2) the back-EMF dominates the rate-of-change in the current; (3) the variation of incremental inductances with rotor position undergoes two cycles per single electrical cycle of the brushless pm machine causing an ambiguity in sensed position; (4) the distortion due to the nonlinearities in the inverter; (5) the load offsets and the noise caused by signal injection. This thesis develops a start-up routine and operation algorithms that enhance the performance of position sensorless control of brushless permanent magnet machines at all speeds, including zero speed, and loads by using a machine integrated, low-cost, SAW torque transducer in place of the rotor position sensor.EThOS - Electronic Theses Online ServicePublic Authority of Applied Education in KuwaitGBUnited Kingdo