Polarization entangled photon-pair source based on quantum nonlinear photonics and interferometry

We present a versatile, high-brightness, guided-wave source of polarization entangled photons, emitted at a telecom wavelength. Photon-pairs are generated using an integrated type-0 nonlinear waveguide, and subsequently prepared in a polarization entangled state via a stabilized fiber interferometer. We show that the single photon emission wavelength can be tuned over more than 50 nm, whereas the single photon spectral bandwidth can be chosen at will over more than five orders of magnitude (from 25 MHz to 4 THz). Moreover, by performing entanglement analysis, we demonstrate a high degree of control of the quantum state via the violation of the Bell inequalities by more than 40 standard deviations. This makes this scheme suitable for a wide range of quantum optics experiments, ranging from fundamental research to quantum information applications. We report on details of the setup, as well as on the characterization of all included components, previously outlined in F. Kaiser et al. (2013 Laser Phys. Lett. 10, 045202).Comment: 16 pages, 7 figure

Investigation of wavelength tunable laser modules for use in future optically switched dense wavelength division multiplexed networks

This thesis investigates the use of fast wavelength tunable laser modules in future optically switched dense wavelength division multiplexed networks (DWDM). The worldwide demand for increasingly greater broadband access has thus far been satisfied by the use of DWDM networks, enabled by the development of the erbium doped amplifier. However as this demand continues to grow electronic switching at network nodes will become a limiting factor, creating a potential bandwidth mismatch between the fibre capacities and switching capacity. Optical switching has been proposed to overcome this electronic bottleneck and fully utilize the enormous bandwidth offered by fibre. Fast tunable lasers (TLs) are a key technology in this area, enabling fast wavelength switching. Experimental work involving the fast wavelength switching of sampled grating distributed Bragg reflector TL modules is presented. Spurious mode generation during wavelength tuning is shown to cause severe cross-channel interference on other data channels in a DWDM test bed. Bit error rate (BER) results demonstrate that a integrated semiconductor optical amplifier can greatly reduce system degradation caused by asynchronous switching of multiple TLs. This is achieved by optically blanking the laser output during channel transition for a period of 60 ns. Immediately after the blanking period a wavelength drift due to the TL module wavelength locking is found to cause cross channel interference and introduce an error floor >1 e-4 on the BER performance characteristic of an adjacent channel in a 12.5 GHz spaced DWDM network. This drift is characterised, using a selfheterodyne and a filter based approach – Error free performance is subsequently demonstrated by using an extended blanking period of 260 ns or by using subcarrier multiplexing transmission and phase selective demodulation before detection. A DWDM optical label switching system, utilizing 40 Gbit/s payload data with low data rate labels placed on a 40 GHz sub-carrier and using TL transmitters is presented. Channel performance is monitored on a static channel as a second data channel is tuned into an adjacent channel on a 100 GHz spaced grid. Error free performance is demonstrated only for the channel payload – Time resolved BER results in agreement with the TL wavelength drift are measured and demonstrate a detrimental influence of the drift on the sub-carrier label performance

Fiber amplifiers, directly modulated transmitters and a ring network structure for optical communications

The three technologies that are considered the key elements in building a metropolitan area optical network are studied in this thesis. They are optical amplification, high-speed low cost transmitters and ring network structures. These studies concentrate on cost reduction of these three technologies thus enabling the use of optical networks in small customer base metropolitan areas. The research on optical amplification concentrated first on the solution doping process, at present the most used method for producing erbium doped fiber. It was found that separationing the soot growth and the sintering improved the uniformity of the porous layer. This made the homogeneity of the doping concentration in the fiber core better. The effects of index profile variations that arise from the non-ideal solution doping process were also simulated. In the search for a better doping method a new nanoparticle glass-forming process, the direct nanoparticle deposition, was developed. In this process the doping is done simultaneously with glass formation. Utilizing this new process it was possible to improve the uniformity of the doping resulting in higher usable doping levels and shorter erbium doped fiber lengths in the amplifiers. There were fewer limitations in the amplifier caused by optical non-linearities and polarization mode dispersion since shorter fiber lengths were needed. The double cladding fiber, which avoids the costly coupling of the pump laser into a single mode waveguide, was also studied. This pumping scheme was found to improve the inversion uniformity in the erbium doped fiber core thereby enhancing the power conversion efficiency for the long wavelength band amplifier. In characterizing the erbium doped fiber amplifier the gain and noise figure was measured with a temporal filter setup. It was made of simple, low cost components but yielded accurate measurements since the noise originating from the amplified spontaneous emission was measured at the signal wavelength. In the study of fiber amplifier controlling schemes the input power of the fiber amplifier was successfully used to regulate the pump laser. This feed-forward control scheme provides a simple, low cost control and managment system for the erbium doped fiber amplifier in metropolitan area network applications that require flexible adding and dropping of wavelength channels. The transmitter research focused on the DFB laser due to its simplicity and low cost structure. A solid state Fabry-Perot etalon made from double polished silicon chip was used as a frequency discriminator in the chirp analyser developed for the DFB lasers. This wavelength discriminator did not require repeated calibration or active stabilisation and was controled electrically enabling automatic measurements. The silicon Fabry-Perot etalon was also used for simultaneous spectral filtering and wavelength control of the laser. The usable dispersion limited transmission length was increased when the filter was used in conjunction with the directly modulated distributed feedback laser transmitter. The combination of spatial multiplexing and dense wavelength division multiplexing in ring topology was investigated in the course of the research on the ring network as the feeder part of the metropolitan network. A new way to organize different wavelengths and fibers was developed. This ring network structure was simulated and an experimental ring network built. The results of the studies demonstrated that the same limitations effecting uni-directional ring structures also are the main limitations on the scalability of the spatial and wavelength division multiplexed ring networks based on bi-directional transmission when the node spacing is short. The developed ring network structure demonstrated major cost reductions when compared with the heavy use of wavelength division multiplexing. The node structure was also greatly simplified resulting in less need for different wavelength transmitters in each node. Furthermore the node generated only minor losses for the passing signals thus reducing the need for optical amplification.reviewe

Development of Low Noise-Broadband Raman Amplification Systems Based on Photonic Crystal Fibers for High Capacity DWDM Networks

The increased demand from IP traffic, video application and cell backhaul has placed fiber routes under severe stains. The high demands for large bandwidth from enormous numbers from cell sites on a network made the capacity of yesterday’s networks not adequate for today’s bandwidth demand. Carries considered Dense Wavelength Division Multiplexing (DWDM) network to overcome this issue. Recently, there has been growing interest in fiber Raman amplifiers due to their capability to upgrade the wavelength-division-multiplexing bandwidth, arbitrary gain bandwidth. In addition, photonic crystal fibers have been widely modeled, studied, and fabricated due to their peculiar properties that cannot be achieved with conventional fibers. The focus of this thesis is to develop a low-noise broadband Raman amplification system based on photonic crystal Fiber that can be implemented in high capacity DWDM network successfully. The design a module of photonic crystal fiber Raman amplifier is based on the knowledge of the fiber cross-sectional characteristics i.e. the geometric parameters and the Germania concentration in the dope area. The module allows to study different air-hole dimension and disposition, with or without a central doped area. In addition the design integrates distributed Raman amplifier and nonlinear optical loop mirror to improve the signal to noise ratio and overall gain in large capacity DWDM network