Adaptive code division multiple access protocol for wireless network-on-chip architectures

Massive levels of integration following Moore\u27s Law ushered in a paradigm shift in the way on-chip interconnections were designed. With higher and higher number of cores on the same die traditional bus based interconnections are no longer a scalable communication infrastructure. On-chip networks were proposed enabled a scalable plug-and-play mechanism for interconnecting hundreds of cores on the same chip. Wired interconnects between the cores in a traditional Network-on-Chip (NoC) system, becomes a bottleneck with increase in the number of cores thereby increasing the latency and energy to transmit signals over them. Hence, there has been many alternative emerging interconnect technologies proposed, namely, 3D, photonic and multi-band RF interconnects. Although they provide better connectivity, higher speed and higher bandwidth compared to wired interconnects; they also face challenges with heat dissipation and manufacturing difficulties. On-chip wireless interconnects is one other alternative proposed which doesn\u27t need physical interconnection layout as data travels over the wireless medium. They are integrated into a hybrid NOC architecture consisting of both wired and wireless links, which provides higher bandwidth, lower latency, lesser area overhead and reduced energy dissipation in communication. However, as the bandwidth of the wireless channels is limited, an efficient media access control (MAC) scheme is required to enhance the utilization of the available bandwidth. This thesis proposes using a multiple access mechanism such as Code Division Multiple Access (CDMA) to enable multiple transmitter-receiver pairs to send data over the wireless channel simultaneously. It will be shown that such a hybrid wireless NoC with an efficient CDMA based MAC protocol can significantly increase the performance of the system while lowering the energy dissipation in data transfer. In this work it is shown that the wireless NoC with the proposed CDMA based MAC protocol outperformed the wired counterparts and several other wireless architectures proposed in literature in terms of bandwidth and packet energy dissipation. Significant gains were observed in packet energy dissipation and bandwidth even with scaling the system to higher number of cores. Non-uniform traffic simulations showed that the proposed CDMA-WiNoC was consistent in bandwidth across all traffic patterns. It is also shown that the CDMA based MAC scheme does not introduce additional reliability concerns in data transfer over the on-chip wireless interconnects

A Scalable & Energy Efficient Graphene-Based Interconnection Framework for Intra and Inter-Chip Wireless Communication in Terahertz Band

Network-on-Chips (NoCs) have emerged as a communication infrastructure for the multi-core System-on-Chips (SoCs). Despite its advantages, due to the multi-hop communication over the metal interconnects, traditional Mesh based NoC architectures are not scalable in terms of performance and energy consumption. Folded architectures such as Torus and Folded Torus were proposed to improve the performance of NoCs while retaining the regular tile-based structure for ease of manufacturing. Ultra-low-latency and low-power express channels between communicating cores have also been proposed to improve the performance of conventional NoCs. However, the performance gain of these approaches is limited due to metal/dielectric based interconnection. Many emerging interconnect technologies such as 3D integration, photonic, Radio Frequency (RF), and wireless interconnects have been envisioned to alleviate the issues of a metal/dielectric interconnect system. However, photonic and RF interconnects need the additional physically overlaid optical waveguides or micro-strip transmission lines to enable data transmission across the NoC. Several on-chip antennas have shown to improve energy efficiency and bandwidth of on-chip data communications. However, the date rates of the mm-wave wireless channels are limited by the state-of-the-art power-efficient transceiver design. Recent research has brought to light novel graphene based antennas operating at THz frequencies. Due to the higher operating frequencies compared to mm-wave transceivers, the data rate that can be supported by these antennas are significantly higher. Higher operating frequencies imply that graphene based antennas are just hundred micrometers in size compared to dimensions in the range of a millimeter of mm-wave antennas. Such reduced dimensions are suitable for integration of several such transceivers in a single NoC for relatively low overheads. In this work, to exploit the benefits of a regular NoC structure in conjunction with emerging Graphene-based wireless interconnect. We propose a toroidal folding based NoC architecture. The novelty of this folding based approach is that we are using low power, high bandwidth, single hop direct point to point wireless links instead of multihop communication that happens through metallic wires. We also propose a novel phased based communication protocol through which multiple wireless links can be made active at a time without having any interference among the transceiver. This offers huge gain in terms of performance as compared to token based mechanism where only a single wireless link can be made active at a time. We also propose to extend Graphene-based wireless links to enable energy-efficient, phase-based chip-to-chip communication to create a seamless, wireless interconnection fabric for multichip systems as well. Through cycle-accurate system-level simulations, we demonstrate that such designs with torus like folding based on THz links instead of global wires along with the proposed phase based multichip systems. We provide estimates that they are able to provide significant gains (about 3 to 4 times better in terms of achievable bandwidth, packet latency and average packet energy when compared to wired system) in performance and energy efficiency in data transfer in a NoC as well as multichip system. Thus, realization of these kind of interconnection framework that could support high data rate links in Tera-bits-per-second that will alleviate the capacity limitations of current interconnection framework

Overcoming the Challenges for Multichip Integration: A Wireless Interconnect Approach

The physical limitations in the area, power density, and yield restrict the scalability of the single-chip multicore system to a relatively small number of cores. Instead of having a large chip, aggregating multiple smaller chips can overcome these physical limitations. Combining multiple dies can be done either by stacking vertically or by placing side-by-side on the same substrate within a single package. However, in order to be widely accepted, both multichip integration techniques need to overcome significant challenges. In the horizontally integrated multichip system, traditional inter-chip I/O does not scale well with technology scaling due to limitations of the pitch. Moreover, to transfer data between cores or memory components from one chip to another, state-of-the-art inter-chip communication over wireline channels require data signals to travel from internal nets to the peripheral I/O ports and then get routed over the inter-chip channels to the I/O port of the destination chip. Following this, the data is finally routed from the I/O to internal nets of the target chip over a wireline interconnect fabric. This multi-hop communication increases energy consumption while decreasing data bandwidth in a multichip system. On the other hand, in vertically integrated multichip system, the high power density resulting from the placement of computational components on top of each other aggravates the thermal issues of the chip leading to degraded performance and reduced reliability. Liquid cooling through microfluidic channels can provide cooling capabilities required for effective management of chip temperatures in vertical integration. However, to reduce the mechanical stresses and at the same time, to ensure temperature uniformity and adequate cooling competencies, the height and width of the microchannels need to be increased. This limits the area available to route Through-Silicon-Vias (TSVs) across the cooling layers and make the co-existence and co-design of TSVs and microchannels extreamly challenging. Research in recent years has demonstrated that on-chip and off-chip wireless interconnects are capable of establishing radio communications within as well as between multiple chips. The primary goal of this dissertation is to propose design principals targeting both horizontally and vertically integrated multichip system to provide high bandwidth, low latency, and energy efficient data communication by utilizing mm-wave wireless interconnects. The proposed solution has two parts: the first part proposes design methodology of a seamless hybrid wired and wireless interconnection network for the horizontally integrated multichip system to enable direct chip-to-chip communication between internal cores. Whereas the second part proposes a Wireless Network-on-Chip (WiNoC) architecture for the vertically integrated multichip system to realize data communication across interlayer microfluidic coolers eliminating the need to place and route signal TSVs through the cooling layers. The integration of wireless interconnect will significantly reduce the complexity of the co-design of TSV based interconnects and microchannel based interlayer cooling. Finally, this dissertation presents a combined trade-off evaluation of such wireless integration system in both horizontal and vertical sense and provides future directions for the design of the multichip system

Robust and Traffic Aware Medium Access Control Mechanisms for Energy-Efficient mm-Wave Wireless Network-on-Chip Architectures

To cater to the performance/watt needs, processors with multiple processing cores on the same chip have become the de-facto design choice. In such multicore systems, Network-on-Chip (NoC) serves as a communication infrastructure for data transfer among the cores on the chip. However, conventional metallic interconnect based NoCs are constrained by their long multi-hop latencies and high power consumption, limiting the performance gain in these systems. Among, different alternatives, due to the CMOS compatibility and energy-efficiency, low-latency wireless interconnect operating in the millimeter wave (mm-wave) band is nearer term solution to this multi-hop communication problem. This has led to the recent exploration of millimeter-wave (mm-wave) wireless technologies in wireless NoC architectures (WiNoC). To realize the mm-wave wireless interconnect in a WiNoC, a wireless interface (WI) equipped with on-chip antenna and transceiver circuit operating at 60GHz frequency range is integrated to the ports of some NoC switches. The WIs are also equipped with a medium access control (MAC) mechanism that ensures a collision free and energy-efficient communication among the WIs located at different parts on the chip. However, due to shrinking feature size and complex integration in CMOS technology, high-density chips like multicore systems are prone to manufacturing defects and dynamic faults during chip operation. Such failures can result in permanently broken wireless links or cause the MAC to malfunction in a WiNoC. Consequently, the energy-efficient communication through the wireless medium will be compromised. Furthermore, the energy efficiency in the wireless channel access is also dependent on the traffic pattern of the applications running on the multicore systems. Due to the bursty and self-similar nature of the NoC traffic patterns, the traffic demand of the WIs can vary both spatially and temporally. Ineffective management of such traffic variation of the WIs, limits the performance and energy benefits of the novel mm-wave interconnect technology. Hence, to utilize the full potential of the novel mm-wave interconnect technology in WiNoCs, design of a simple, fair, robust, and efficient MAC is of paramount importance. The main goal of this dissertation is to propose the design principles for robust and traffic-aware MAC mechanisms to provide high bandwidth, low latency, and energy-efficient data communication in mm-wave WiNoCs. The proposed solution has two parts. In the first part, we propose the cross-layer design methodology of robust WiNoC architecture that can minimize the effect of permanent failure of the wireless links and recover from transient failures caused by single event upsets (SEU). Then, in the second part, we present a traffic-aware MAC mechanism that can adjust the transmission slots of the WIs based on the traffic demand of the WIs. The proposed MAC is also robust against the failure of the wireless access mechanism. Finally, as future research directions, this idea of traffic awareness is extended throughout the whole NoC by enabling adaptiveness in both wired and wireless interconnection fabric

FDMA Enabled Phase-based Wireless Network-on-Chip using Graphene-based THz-band Antennas

The future growth in System-on-chip design is moving in the direction of multicore systems. Design of efficient interconnects between cores are crucial for improving the performance of a multicore processor. Such trends are seen due to the benefits the multicore systems provide in terms of power reduction and scalability. Network-on-chips (NoC) are viewed as an emerging solution in the design of interconnects in multicore systems. However, Traditional Network-on-chip architectures are no longer able to satisfy the performance requirements due to long distance communication over multi-hop wireline paths. Multi-hop communication leads to higher energy consumption, increase in latency and reduction in bandwidth. Research in recent years has explored emerging technologies such as 3D integration, photonic and radio frequency based Network-on-chips. The use of wireless interconnects using mm-wave antennas are able to alleviate the performance issues in a wireline interconnect system. However, to satisfy the increasing demand for higher bandwidth and lower energy consumption, Wireless Network-on-Chip enabled with high speed direct links operating in THz band between distant cores is desired. Recent research has brought to light highly efficient graphene-based antennas operating in THz band. These antennas can provide high data rate and are found to consume less power with low area overheads. In this thesis, an innovative approach using novel devices based on graphene structures is proposed to provide a high-performance on-chip interconnection. This novel approach combines the regular NoC structure with the proposed wireless infrastructure to exploit the performance benefits. An architecture with wireless interfaces on every core is explored in this work. Simultaneous multiple communications in a network can be achieved by adopting Frequency Division Multiple access (FDMA). However, in a system where all cores are equipped with a wireless interface, FDMA requires more number of frequency bands. This becomes difficult to achieve as the system scales and the number of cores increase. Therefore, a FDMA protocol along with a 4-phased repetitive multi-band architecture is envisioned in this work. The phase-based protocol allows multiple wireless links to be active at a time, the phase-based protocol along with the FDMA protocol provides a reliable data transfer between cores with lesser number of frequency bands. In this thesis, an architecture with a combination of FDMA and phase-based protocol using point-to-point graphene-based wireless links is proposed. The proposed architecture is also extended for a multichip system. With cycle accurate system-level simulations, it is shown that the proposed architecture provides huge gains in performance and energy-efficiency in data transfer both in NoC based multicore and multichip systems

Using Proportional-Integral-Differential approach for Dynamic Traffic Prediction in Wireless Network-on-Chip

The massive integration of cores in multi-core system has enabled chip designer to design systems while meeting the power performance demands of the applications. Wireless interconnection has emerged as an energy efficient solution to the challenges of multi-hop communication over the wireline paths in conventional Networks-on-Chips (NoCs). However, to ensure the full benefits of this novel interconnect technology, design of simple, fair and efficient Medium Access Control (MAC) mechanism to grant access to the on-chip wireless communication channel is needed. Moreover, to adapt to the varying traffic demands from the applications running on a multicore environment, MAC mechanisms should dynamically adjust the transmission slots of the wireless interfaces (WIs). To ensure an efficient utilization of the wireless medium in a Wireless NoC (WiNoC), in this work we present the design of prediction model that is used by two dynamic MAC mechanism to predict the traffic demand of the WIs and respond accordingly by adjusting transmission slots of the WIs. Through system level simulations, we show that the traffic aware MAC mechanisms are more energy efficient as well as capable of sustaining higher data bandwidth in WiNoCs

Communication Subsystems for Emerging Wireless Technologies

The paper describes a multi-disciplinary design of modern communication systems. The design starts with the analysis of a system in order to define requirements on its individual components. The design exploits proper models of communication channels to adapt the systems to expected transmission conditions. Input filtering of signals both in the frequency domain and in the spatial domain is ensured by a properly designed antenna. Further signal processing (amplification and further filtering) is done by electronics circuits. Finally, signal processing techniques are applied to yield information about current properties of frequency spectrum and to distribute the transmission over free subcarrier channels

The Chameleon Architecture for Streaming DSP Applications

We focus on architectures for streaming DSP applications such as wireless baseband processing and image processing. We aim at a single generic architecture that is capable of dealing with different DSP applications. This architecture has to be energy efficient and fault tolerant. We introduce a heterogeneous tiled architecture and present the details of a domain-specific reconfigurable tile processor called Montium. This reconfigurable processor has a small footprint (1.8 mm$^2$ in a 130 nm process), is power efficient and exploits the locality of reference principle. Reconfiguring the device is very fast, for example, loading the coefficients for a 200 tap FIR filter is done within 80 clock cycles. The tiles on the tiled architecture are connected to a Network-on-Chip (NoC) via a network interface (NI). Two NoCs have been developed: a packet-switched and a circuit-switched version. Both provide two types of services: guaranteed throughput (GT) and best effort (BE). For both NoCs estimates of power consumption are presented. The NI synchronizes data transfers, configures and starts/stops the tile processor. For dynamically mapping applications onto the tiled architecture, we introduce a run-time mapping tool

Design Trade-offs for reliable On-Chip Wireless Interconnects in NoC Platforms

The massive levels of integration following Moore\u27s Law making modern multi-core chips prevail in various domains ranging from scientific applications to bioinformatics applications for consumer electronics. With higher and higher number of cores on the same die traditional bus based interconnections are no longer a scalable communication infrastructure. On-chip networks were proposed enabled a scalable plug-and-play mechanism for interconnecting hundreds of cores on the same chip. Wired interconnects between the cores in a traditional Network-on-Chip (NoC) system, becomes a bottleneck with increase in the number of cores thereby increasing the latency and energy to transmit signals over them. Hence, there has been many alternative emerging interconnect technologies proposed, namely, 3D, photonic and multi-band RF interconnects. Although they provide better connectivity, higher speed and higher bandwidth compared to wired interconnects; they also face challenges with heat dissipation and manufacturing difficulties. On-chip wireless interconnects is one other alternative proposed which doesn\u27t need physical interconnection layout as data travels over the wireless medium. They are integrated into a hybrid NOC architecture consisting of both wired and wireless links, which provides higher bandwidth, lower latency, lesser area overhead and reduced energy dissipation in communication. An efficient media access control (MAC) scheme is required to enhance the utilization of the available bandwidth. A token-passing protocol proposed to grant access of the wireless channel to competing transmitters. This limits the number of simultaneous users of the communication channel to one although multiple wireless hubs are deployed over the chip. In principle, a Frequency Division Multiple Access (FDMA) based medium access scheme would improve the utilization of the wireless resources. However, this requires design of multiple very precise, high frequency transceivers in non-overlapping frequency channels. Therefore, the scalability of this approach is limited by the state-of-the-art in transceiver design. The Code Division Multiple Access (CDMA) enables multiple transmitter-receiver pairs to send data over the wireless channel simultaneously. The CDMA protocol can significantly increase the performance of the system while lowering the energy dissipation in data transfer. The CDMA based MAC protocol outperforms the wired counterparts and several other wireless architectures proposed in literature in terms of bandwidth and packet energy dissipation. However, the reliability of CDMA based wireless NoC\u27s is limited, as the probability of error is eminent due to synchronization delays at the receiver. The thesis proposes the use of an advanced filter which improves the performance and also reduces the error due to synchronization delays. This thesis also proposes investigation of various channel modulation schemes on token passing wireless NoC\u27s to examine the performance and reliability of the system. The trade-off between performance and energy are established for the various conditions. The results are obtained using a modified cycle accurate simulator

Wireless Interconnects for Intra-chip & Inter-chip Transmission

With the emergence of Internet of Things and information revolution, the demand of high performance computing systems is increasing. The copper interconnects inside the computing chips have evolved into a sophisticated network of interconnects known as Network on Chip (NoC) comprising of routers, switches, repeaters, just like computer networks. When network on chip is implemented on a large scale like in Multicore Multichip (MCMC) systems for High Performance Computing (HPC) systems, length of interconnects increases and so are the problems like power dissipation, interconnect delays, clock synchronization and electrical noise. In this thesis, wireless interconnects are chosen as the substitute for wired copper interconnects. Wireless interconnects offer easy integration with CMOS fabrication and chip packaging. Using wireless interconnects working at unlicensed mm-wave band (57-64GHz), high data rate of Gbps can be achieved. This thesis presents study of transmission between zigzag antennas as wireless interconnects for Multichip multicores (MCMC) systems and 3D IC. For MCMC systems, a four-chips 16-cores model is analyzed with only four wireless interconnects in three configurations with different antenna orientations and locations. Return loss and transmission coefficients are simulated in ANSYS HFSS. Moreover, wireless interconnects are designed, fabricated and tested on a 6’’ silicon wafer with resistivity of 55Ω-cm using a basic standard CMOS process. Wireless interconnect are designed to work at 30GHz using ANSYS HFSS. The fabricated antennas are resonating around 20GHz with a return loss of less than -10dB. The transmission coefficients between antenna pair within a 20mm x 20mm silicon die is found to be varying between -45dB to -55dB. Furthermore, wireless interconnect approach is extended for 3D IC. Wireless interconnects are implemented as zigzag antenna. This thesis extends the work of analyzing the wireless interconnects in 3D IC with different configurations of antenna orientations and coolants. The return loss and transmission coefficients are simulated using ANSYS HFSS