On chip interconnects for multiprocessor turbo decoding architectures

International audienc

An Opportunistic Error Correction Layer for OFDM Systems

In this paper, we propose a novel cross layer scheme to lower power\ud consumption of ADCs in OFDM systems, which is based on resolution\ud adaptive ADCs and Fountain codes. The key part in the new proposed\ud system is that the dynamic range of ADCs can be reduced by\ud discarding the packets which are transmitted over 'bad' sub\ud carriers. Correspondingly, the power consumption in ADCs can be\ud reduced. Also, the new system does not process all the packets but\ud only processes surviving packets. This new error correction layer\ud does not require perfect channel knowledge, so it can be used in a\ud realistic system where the channel is estimated. With this new\ud approach, more than 70% of the energy consumption in the ADC can be\ud saved compared with the conventional IEEE 802.11a WLAN system under\ud the same channel conditions and throughput. The ADC in a receiver\ud can consume up to 50% of the total baseband energy. Moreover, to\ud reduce the overhead of Fountain codes, we apply message passing and\ud Gaussian elimination in the decoder. In this way, the overhead is\ud 3% for a small block size (i.e. 500 packets). Using both methods\ud results in an efficient system with low delay

Configurable and Scalable Turbo Decoder for 4G Wireless Receivers

The increasing requirements of high data rates and quality of service (QoS) in fourth-generation (4G) wireless communication require the implementation of practical capacity approaching codes. In this chapter, the application of Turbo coding schemes that have recently been adopted in the IEEE 802.16e WiMax standard and 3GPP Long Term Evolution (LTE) standard are reviewed. In order to process several 4G wireless standards with a common hardware module, a reconfigurable and scalable Turbo decoder architecture is presented. A parallel Turbo decoding scheme with scalable parallelism tailored to the target throughput is applied to support high data rates in 4G applications. High-level decoding parallelism is achieved by employing contention-free interleavers. A multi-banked memory structure and routing network among memories and MAP decoders are designed to operate at full speed with parallel interleavers. A new on-line address generation technique is introduced to support multiple Turbo interleaving patterns, which avoids the interleaver address memory that is typically necessary in the traditional designs. Design trade-offs in terms of area and power efficiency are analyzed for different parallelism and clock frequency goals

Low Complexity Wireless Communication Digital Baseband Design

abstract: This thesis addresses two problems in digital baseband design of wireless communication systems, namely, those in Internet of Things (IoT) terminals that support long range communications and those in full-duplex systems that are designed for high spectral efficiency. IoT terminals for long range communications are typically based on Orthogonal Frequency-Division Multiple Access (OFDMA) and spread spectrum technologies. In order to design an efficient baseband architecture for such terminals, the workload profiles of both systems are analyzed. Since frame detection unit has by far the highest computational load, a simple architecture that uses only a scalar datapath is proposed. To optimize for low energy consumption, application-specific instructions that minimize register accesses and address generation units for streamlined memory access are introduced. Two parameters, namely, correlation window size and threshold value, affect the detection probability, the false alarm probability and hence energy consumption. Next, energy-optimal operation settings for correlation window size and threshold value are derived for different channel conditions. For both good and bad channel conditions, if target signal detection probability is greater than 0.9, the baseband processor has the lowest energy when the frame detection algorithm uses the longest correlation window and the highest threshold value. A full-duplex system has high spectral efficiency but suffers from self-interference. Part of the interference can be cancelled digitally using equalization techniques. The cancellation performance and computation complexity of the competing equalization algorithms, namely, Least Mean Square (LMS), Normalized LMS (NLMS), Recursive Least Square (RLS) and feedback equalizers based on LMS, NLMS and RLS are analyzed, and a trade-off between performance and complexity established. NLMS linear equalizer is found to be suitable for resource-constrained mobile devices and NLMS decision feedback equalizer is more appropriate for base stations that are not energy constrained.Dissertation/ThesisMasters Thesis Electrical Engineering 201

VLSI implementation of a multi-mode turbo/LDPC decoder architecture

Flexible and reconfigurable architectures have gained wide popularity in the communications field. In particular, reconfigurable architectures for the physical layer are an attractive solution not only to switch among different coding modes but also to achieve interoperability. This work concentrates on the design of a reconfigurable architecture for both turbo and LDPC codes decoding. The novel contributions of this paper are: i) tackling the reconfiguration issue introducing a formal and systematic treatment that, to the best of our knowledge, was not previously addressed; ii) proposing a reconfigurable NoCbased turbo/LDPC decoder architecture and showing that wide flexibility can be achieved with a small complexity overhead. Obtained results show that dynamic switching between most of considered communication standards is possible without pausing the decoding activity. Moreover, post-layout results show that tailoring the proposed architecture to the WiMAX standard leads to an area occupation of 2.75 mm2 and a power consumption of 101.5 mW in the worst case

Architectures multi-Asip pour turbo récepteur flexible

Rapidly evolving wireless standards use modern techniques such as turbo codes, Bit Interleaved coded Modulation (BICM), high order QAM constellation, Signal Space Diversity (SSD), Multi-Input Multi-Output (MIMO) Spatial Multiplexing (SM) and Space Time Codes (STC) with different parameters for reliable high rate data transmissions. Adoption of such techniques in the transmitter can impact the receiver architecture in three ways: (1) the complex processing related to advanced techniques such as turbo codes, encourage to perform iterative processing in the receiver to improve error rate performance (2) to satisfy high throughput requirement for an iterative receiver, parallel processing is mandatory and finally (3) to allow the support of different techniques and parameters imposed, programmable yet high throughput hardware processing elements are required. In this thesis, to address the high throughput requirement with turbo processing, first of all a study of parallelism on turbo decoding is extended for turbo demodulation and turbo equalization. Based on the results acquired from the parallelism study a flexible high throughput heterogeneous multi-ASIP NoC based unified turbo receiver is proposed. The proposed architecture fulfils the target requirements in a way that: (a) Application Specific Instruction-set Processor (ASIP) exploits metric generation level parallelism and implements the required flexibility, (b) throughputs beyond the capacity of single ASIP in a turbo process are achieved through multiple ASIP elements implementing sub-block parallelism and shuffled processing and finally (c) Network on Chip is used to handle communication conflicts during parallel processing of multiple ASIPs. In pursuit to achieve a hardware model of the proposed architecture two ASIPs are conceived where the first one, namely EquASIP, is dedicated for MMSE-IC equalization and provides a flexible solution for multiple MIMO techniques adopted in multiple wireless standards with a capability to work in turbo equalization context. The second ASIP, named as DemASIP, is a flexible demapper which can be used in MIMO or single antenna environment for any modulation till 256-QAM with or without iterative demodulation. Using available TurbASIP and NoC components, the thesis concludes on an FPGA prototype of heterogeneous multi-ASIP NoC based unified turbo receiver which integrates 9 instances of 3 different ASIPs with 2 NoCs.Les normes de communication sans fil, sans cesse en évolution, imposent l'utilisation de techniques modernes telles que les turbocodes, modulation codée à entrelacement bit (BICM), constellation MAQ d'ordre élevé, diversité de constellation (SSD), multiplexage spatial et codage espace-temps multi-antennes (MIMO) avec des paramètres différents pour des transmissions fiables et de haut débit. L'adoption de ces techniques dans l'émetteur peut influencer l'architecture du récepteur de trois façons: (1) les traitement complexes relatifs aux techniques avancées comme les turbocodes, encourage à effectuer un traitement itératif dans le récepteur pour améliorer la performance en termes de taux d'erreur (2) pour satisfaire l'exigence de haut débit avec un récepteur itératif, le recours au parallélisme est obligatoire et enfin (3) pour assurer le support des différentes techniques et paramètres imposées, des processeurs de traitement matériel flexibles, mais aussi de haute performance, sont nécessaires. Dans cette thèse, pour répondre aux besoins de haut débit dans un contexte de traitement itératif, tout d'abord une étude de parallélisme sur le turbo décodage a été étendue aux applications de turbo démodulation et turbo égalisation. Partant des résultats obtenus à partir de l'étude du parallélisme, un récepteur itératif unifié basé sur un modèle d'architecture multi-ASIP hétérogène intégrant un réseau sur puce (NoC) a été proposé. L'architecture proposée répond aux exigences visées d'une manière où: (a) le concept de processeur à jeu d'instruction dédié à l'application (ASIP) exploite le parallélisme du niveau de génération de métriques et met en oeuvre la flexibilité nécessaire, (b) les débits au-delà de la capacité d'un seul ASIP dans un processus itératif sont obtenus au moyen de multiples ASIP implémentant le parallélisme de sous-blocs et le traitement combiné et enfin (c) le concept de réseau sur puce (NoC) est utilisé pour gérer les conflits de communication au cours du traitement parallèle itératif multi-ASIP. Dans le but de parvenir à un modèle matériel de l'architecture proposée, deux ASIP ont été conçus où le premier, nommé EquASIP, est dédié à l'égalisation MMSE-IC et fournit une solution flexible pour de multiples techniques multi-antennes adoptés dans plusieurs normes sans fil avec la capacité de travailler dans un contexte de turbo égalisation. Le deuxième ASIP, nommé DemASIP, est un démappeur flexible qui peut être utilisé dans un environnement multi-antennes et pour tout type de modulation jusqu'à MAQ-256 avec ou sans démodulation itérative. En intégrant ces ASIP, en plus des NoC et TurbASIP disponibles à Télécom Bretagne, la thèse conclut sur un prototype FPGA d'un récepteur itératif unifié multi-ASIP qui intègre 9 coeurs de 3 différents types d'ASIP avec 2 NoC

System capacity enhancement for 5G network and beyond

A thesis submitted to the University of Bedfordshire, in fulfilment of the requirements for the degree of Doctor of PhilosophyThe demand for wireless digital data is dramatically increasing year over year. Wireless communication systems like Laptops, Smart phones, Tablets, Smart watch, Virtual Reality devices and so on are becoming an important part of people’s daily life. The number of mobile devices is increasing at a very fast speed as well as the requirements for mobile devices such as super high-resolution image/video, fast download speed, very short latency and high reliability, which raise challenges to the existing wireless communication networks. Unlike the previous four generation communication networks, the fifth-generation (5G) wireless communication network includes many technologies such as millimetre-wave communication, massive multiple-input multiple-output (MIMO), visual light communication (VLC), heterogeneous network (HetNet) and so forth. Although 5G has not been standardised yet, these above technologies have been studied in both academia and industry and the goal of the research is to enhance and improve the system capacity for 5G networks and beyond by studying some key problems and providing some effective solutions existing in the above technologies from system implementation and hardware impairments’ perspective. The key problems studied in this thesis include interference cancellation in HetNet, impairments calibration for massive MIMO, channel state estimation for VLC, and low latency parallel Turbo decoding technique. Firstly, inter-cell interference in HetNet is studied and a cell specific reference signal (CRS) interference cancellation method is proposed to mitigate the performance degrade in enhanced inter-cell interference coordination (eICIC). This method takes carrier frequency offset (CFO) and timing offset (TO) of the user’s received signal into account. By reconstructing the interfering signal and cancelling it afterwards, the capacity of HetNet is enhanced. Secondly, for massive MIMO systems, the radio frequency (RF) impairments of the hardware will degrade the beamforming performance. When operated in time duplex division (TDD) mode, a massive MIMO system relies on the reciprocity of the channel which can be broken by the transmitter and receiver RF impairments. Impairments calibration has been studied and a closed-loop reciprocity calibration method is proposed in this thesis. A test device (TD) is introduced in this calibration method that can estimate the transmitters’ impairments over-the-air and feed the results back to the base station via the Internet. The uplink pilots sent by the TD can assist the BS receivers’ impairment estimation. With both the uplink and downlink impairments estimates, the reciprocity calibration coefficients can be obtained. By computer simulation and lab experiment, the performance of the proposed method is evaluated. Channel coding is an essential part of a wireless communication system which helps fight with noise and get correct information delivery. Turbo codes is one of the most reliable codes that has been used in many standards such as WiMAX and LTE. However, the decoding process of turbo codes is time-consuming and the decoding latency should be improved to meet the requirement of the future network. A reverse interleave address generator is proposed that can reduce the decoding time and a low latency parallel turbo decoder has been implemented on a FPGA platform. The simulation and experiment results prove the effectiveness of the address generator and show that there is a trade-off between latency and throughput with a limited hardware resource. Apart from the above contributions, this thesis also investigated multi-user precoding for MIMO VLC systems. As a green and secure technology, VLC is achieving more and more attention and could become a part of 5G network especially for indoor communication. For indoor scenario, the MIMO VLC channel could be easily ill-conditioned. Hence, it is important to study the impact of the channel state to the precoding performance. A channel state estimation method is proposed based on the signal to interference noise ratio (SINR) of the users’ received signal. Simulation results show that it can enhance the capacity of the indoor MIMO VLC system

Arquiteturas paralelas avançadas para transmissores 5G totalmente digitais

The fifth generation of mobile communications (5G) is being prepared and should be rolled out in the early coming years. Massive number of Radio-Frequency (RF) front-ends, peak data rates of 10 Gbps (everywhere and everytime), latencies lower than 10 msec and huge device densities are some of the expected disruptive capabilities. At the same time, previous generations can not be jeopardized, fostering the design of novel flexible and highly integrated radio transceivers able to support the simultaneous transmission of multi-band and multi-standard signals. The concept of all-digital transmission is being pointed out as a promising architecture to cope with such challenging requirements, due to its fully digital radio datapath. This thesis is focused on the proposal and validation of fully integrated and advanced digital transmitter architectures that excel the state-of-the-art in different figures of merit, such as transmission bandwidth, spectral purity, carrier agility, flexibility, and multi-band capability. The first part of this thesis introduces the concept of all-digital RF transmission. In particular, the foundations inherent to this thematic line are given, together with the recent advances reported in the state-of-the-art architectures.The core of this thesis, containing the main developments achieved during the Ph.D. work, is then presented and discussed. The first key contribution to the state-of-the-art is the use of cascaded Delta-Sigma (∆Σ) architectures to relax the analog filtering requirements of the conventional All-Digital Transmitters while maintaining the constant envelope waveform. Then, it is presented the first reported architecture where Antenna Arrays are directly driven by single-chip and single-bit All-Digital Transmitters, with promising results in terms of simplification of the RF front-ends and overall flexibility. Subsequently, the thesis proposes the first reported RF-stage All-Digital Transmitter that can be embedded within a single Field-Programmable Gate Array (FPGA) device. Thereupon, novel techniques to enable the design of wideband All-Digital Transmitters are reported. Finally, the design of concurrent multi-band transmitters is introduced. In particular, the design of agile and flexible dual and triple bands All-DigitalTransmitter (ADT) is demonstrated, which is a very important topic for scenarios that demand carrier aggregation. This Ph.D. contributes withseveral advances to the state-of-the-art of RF all-digital transmitters.A quinta geração de comunicações móveis (5G) está a ser preparada e deve ser comercializada nos próximos anos. Algumas das caracterı́sticas inovadoras esperadas passam pelo uso de um número massivo de font-ends de Rádio-Frequência (RF), taxas de pico de transmissão de dados de 10 Gbps (em todos os lugares e em todas as ocasiões), latências inferiores a 10 mseg e elevadas densidades de dispositivos. Ao mesmo tempo, as gerações anteriores não podem ser ignoradas, fomentando o design de novos transceptores de rádio flexı́veis e altamente integrados, capazes de suportar a transmissão simultânea de sinais multi-banda e multi-standard. O conceito de transmissão totalmente digital é considerado como um tipo de arquitetura promissora para lidar com esses requisitos desafiantes, devido ao seu datapath de rádio totalmente digital. Esta tese é focada na proposta e validação de arquiteturas de transmissores digitais totalmente integradas e avançadas que ultrapassam o estado da arte em diferentes figuras de mérito, como largura de banda de transmissão, pureza espectral, agilidade de portadora, flexibilidade e capacidade multibanda. A primeira parte desta tese introduz o conceito de transmissores de RF totalmente digitais. Em particular, os fundamentos inerentes a esta linha temática são apresentados, juntamente com os avanços mais recentes do estado-da-arte. O núcleo desta tese, contendo os principais desenvolvimentos alcançados durante o trabalho de doutoramento, é então apresentado e discutido. A primeira contribuição fundamental para o estado da arte é o uso de arquiteturas em cascata com moduladores ∆Σ para relaxar os requisitos de filtragem analógica dos transmissores RF totalmente digitais convencionais, mantendo a forma de onda envolvente constante. Em seguida, é apresentada a primeira arquitetura em que agregados de antenas são excitados diretamente por transmissores digitais de um único bit inseridos num único chip, com resultados promissores em termos de simplificação dos front-ends de RF e flexibilidade em geral. Posteriormente, é proposto o primeiro transmissor totalmente digital RF-stage relatado que pode ser incorporado dentro de um único Agregado de Células Lógicas Programáveis. Novas técnicas para permitir o desenho de transmissores RF totalmente digitais de banda larga são também apresentadas. Finalmente, o desenho de transmissores simultâneos de múltiplas bandas é exposto. Em particular, é demonstrado o desenho de transmissores de duas e três bandas ágeis e flexı́veis, que é um tópico essencial para cenários que exigem agregação de múltiplas bandas.Apoio financeiro da Fundação para a Ciência e Tecnologia (FCT) no âmbito de uma bolsa de doutoramento, ref. PD/BD/105857/2014.Programa Doutoral em Telecomunicaçõe

Design and Implementation of a Low Complexity VLSI Turbo-Code Decoder Architecture for Low Energy Mobile Wireless Communications

Channel coding is commonly incorporated to obtain sufficient reception quality in wireless mobile communications transceiver to counter channel degradation due to intersymbol interference, multipath dispersion, and thermal noise induced by electronic circuit devices. For low energy mobile wireless communications, it is highly desirable to incorporate a decoder which has a very low power consumption while achieving a high coding gain. In this paper, a sub-optimal low-complexity multi-stage pipeline decoder architecture for a powerful channel coding technique known as “turbo-code” is presented. The presented architecture avoids complex operations such as exponent and logarithmic computations. The turbo-code decoding algorithm is reformulated for an efficient VLSI implementation. Furthermore, the communication channel statistic estimation process has been completely eliminated. The architecture has been designed and implemented with the 0.6 μm CMOS standard cell technology using Epoch computer aided design tool. The performance and the circuit complexity of the turbo-code decoder are evaluated and compared with the other types of well-known decoders. The power consumption of the low-complexity turbo-code decoder is comparable to that of the conventional convolutional-code decoder. However, the low-complexity turbo-code decoder has a significant coding gain over the conventional convolutional-code decoders and it is well suited for very low power applications.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/41335/1/11265_2004_Article_253264.pd

VLSI Architectures for WIMAX Channel Decoders

This chapter describes the main architectures proposed in the literature to implement the channel decoders required by the WiMax standard, namely convolutional codes, turbo codes (both block and convolutional) and LDPC. Then it shows a complete design of a convolutional turbo code encoder/decoder system for WiMax.Comment: To appear in the book "WIMAX, New Developments", M. Upena, D. Dalal, Y. Kosta (Ed.), ISBN978-953-7619-53-