217 research outputs found

    Low energy digital circuits in advanced nanometer technologies

    Get PDF
    The demand for portable devices and the continuing trend towards the Internet ofThings (IoT) have made of energy consumption one of the main concerns in the industry and researchers. The most efficient way of reducing the energy consump-tion of digital circuits is decreasing the supply voltage (Vdd) since the dynamicenergy quadratically depends onVdd. Several works have shown that an optimumsupply voltage exists that minimizes the energy consumption of digital circuits. This optimum supply voltage is usually around 200 mV and 400 mV dependingon the circuit and technology used. To obtain these low supply voltages, on-chipdc-dc converters with high efficiency are needed.This thesis focuses on the study of subthreshold digital systems in advancednanometer technologies. These systems usually can be divided into a Power Man-agement Unit (PMU) and a digital circuit operating at the subthreshold regime.In particular, while considering the PMU, one of the key circuits is the dc-dcconverter. This block converts the voltage from the power source (battery, supercapacitor or wireless power transfer link) to a voltage between 200 mV and 400mV in order to power the digital circuit. In this thesis, we developed two chargerecycling techniques in order to improve the efficiency of switched capacitors dc-dcconverters. The first one is based on a technique used in adiabatic circuits calledstepwise charging. This technique was used in circuits and applications wherethe switching consumption of a big capacitance is very important. We analyzedthe possibility of using this technique in switched capacitor dc-dc converters withintegrated capacitors. We showed through measurements that a 29% reductionin the gate drive losses can be obtained with this technique. The second one isa simplification of stepwise charging which can be applied in some architecturesof switched capacitors dc-dc converters. We also fabricated and tested a dc-dcconverter with this technique and obtained a 25% energy reduction in the drivingof the switches that implement the converter.Furthermore, we studied the digital circuit working in the subthreshold regime,in particular, operating at the minimum energy point. We studied different modelsfor circuits working in these conditions and improved them by considering thedifferences between the NMOS and PMOS transistors. We obtained an optimumNMOS/PMOS leakage current imbalance that minimizes the total leakage energy per operation. This optimum depends on the architecture of the digital circuitand the input data. However, we also showed that important energy reductionscan be obtained by operating at a mean optimum imbalance. We proposed two techniques to achieve the optimum imbalance. We used aFully Depleted Silicon on Insulator (FD-SOI) 28 nm technology for most of the simulations, but we also show that these techniques can be applied in traditionalbulk CMOS technologies. The first one consists in using the back plane voltage of the transistors (or bulk voltage in traditional CMOS) to adjust independently theleakage current of the NMOS and PMOS transistor to work under the optimum NMOS/PMOS leakage current imbalance. We called this approach the OptimumBack Plane Biasing (OBB). A second technique consists of using the length of the transistors to adjust this leakage current imbalance. In the subthreshold regimeand in advanced nanometer technologies a moderate increase in the length has little impact in the output capacitance of the gates and thus in the dynamic energy.We called this approach an Asymmetric Length Biasing (ALB). Finally, we use these techniques in some basic circuits such as adders. We show that around 50% energy reduction can be obtained, in a wide range of frequency while working near the minimum energy point and using these techniques. The main contributions of this thesis are: • Analysis of the stepwise charging technique in small capacitances. •Implementation of stepwise charging technique as a charge recycling tech-nique for efficiency improvement in switched capacitor dc-dc converters. • Development of a charge sharing technique for efficiency improvement inswitched capacitor dc-dc converters. • Analysis of minimum operating voltage of digital circuits due to intrinsicnoise and the impact of technology scaling in this minimum. • Improvement in the modeling of the minimum energy point while considering NMOS and PMOS transistors difference. • Demonstration of the existence of an optimum leakage current imbalance be-tween the NMOS and PMOS transistors that minimizes energy consumptionin the subthreshold regiion. • Development of a back plane (bulk) voltage strategy for working in this optimum.• Development of a sizing strategy for working in the aforementioned optimum. • Analysis of the impact of architecture and input data on the optimum im-balance. The thesis is based on the publications [1–8]. During the Ph.D. program, other publications were generated [9–16] that are partially related with the thesis butwere not included in it.La constante demanda de dispositivos portables y los avances hacia la Internet de las Cosas han hecho del consumo de energía uno de los mayores desafíos y preocupación en la industria y la academia. La forma más eficiente de reducir el consumo de energía de los circuitos digitales es reduciendo su voltaje de alimentación ya que la energía dinámica depende de manera cuadrática con dicho voltaje. Varios trabajos demostraron que existe un voltaje de alimentación óptimo, que minimiza la energía consumida para realizar cierta operación en un circuito digital, llamado punto de mínima energía. Este óptimo voltaje se encuentra usualmente entre 200 mV y 400 mV dependiendo del circuito y de la tecnología utilizada. Para obtener estos voltajes de alimentación de la fuente de energía, se necesitan conversores dc-dc integrados con alta eficiencia. Esta tesis se concentra en el estudio de sistemas digitales trabajando en la región sub umbral diseñados en tecnologías nanométricas avanzadas (28 nm). Estos sistemas se pueden dividir usualmente en dos bloques, uno llamado bloque de manejo de potencia, y el segundo, el circuito digital operando en la region sub umbral. En particular, en lo que corresponde al bloque de manejo de potencia, el circuito más crítico es en general el conversor dc-dc. Este circuito convierte el voltaje de una batería (o super capacitor o enlace de transferencia inalámbrica de energía o unidad de cosechado de energía) en un voltaje entre 200 mV y 400 mV para alimentar el circuito digital en su voltaje óptimo. En esta tesis desarrollamos dos técnicas que, mediante el reciclado de carga, mejoran la eficiencia de los conversores dc-dc a capacitores conmutados. La primera es basada en una técnica utilizada en circuitos adiabáticos que se llama carga gradual o a pasos. Esta técnica se ha utilizado en circuitos y aplicaciones en donde el consumo por la carga y descarga de una capacidad grande es dominante. Nosotros analizamos la posibilidad de utilizar esta técnica en conversores dc-dc a capacitores conmutados con capacitores integrados. Se demostró a través de medidas que se puede reducir en un 29% el consumo debido al encendido y apagado de las llaves que implementan el conversor dc-dc. La segunda técnica, es una simplificación de la primera, la cual puede ser aplicada en ciertas arquitecturas de conversores dc-dc a capacitores conmutados. También se fabricó y midió un conversor con esta técnica y se obtuvo una reducción del 25% en la energía consumida por el manejo de las llaves del conversor. Por otro lado, estudiamos los circuitos digitales operando en la región sub umbral y en particular cerca del punto de mínima energía. Estudiamos diferentes modelos para circuitos operando en estas condiciones y los mejoramos considerando las diferencias entre los transistores NMOS y PMOS. Mediante este modelo demostramos que existe un óptimo en la relación entre las corrientes de fuga de ambos transistores que minimiza la energía de fuga consumida por operación. Este óptimo depende de la arquitectura del circuito digital y ademas de los datos de entrada del circuito. Sin embargo, demostramos que se puede reducir el consumo de manera considerable al operar en un óptimo promedio. Propusimos dos técnicas para alcanzar la relación óptima. Utilizamos una tecnología FD-SOI de 28nm para la mayoría de las simulaciones, pero también mostramos que estas técnicas pueden ser utilizadas en tecnologías bulk convencionales. La primer técnica, consiste en utilizar el voltaje de la puerta trasera (o sustrato en CMOS convencional) para ajustar de manera independiente las corrientes del NMOS y PMOS para que el circuito trabaje en el óptimo de la relación de corrientes. Esta técnica la llamamos polarización de voltaje de puerta trasera óptimo. La segunda técnica, consiste en utilizar los largos de los transistores para ajustar las corrientes de fugas de cada transistor y obtener la relación óptima. Trabajando en la región sub umbral y en tecnologías avanzadas, incrementar moderadamente el largo del transistor tiene poco impacto en la energía dinámica y es por eso que se puede utilizar. Finalmente, utilizamos estas técnicas en circuitos básicos como sumadores y mostramos que se puede obtener una reducción de la energía consumida de aproximadamente 50%, en un amplio rango de frecuencias, mientras estos circuitos trabajan cerca del punto de energía mínima. Las principales contribuciones de la tesis son: • Análisis de la técnica de carga gradual o a pasos en capacidades pequeñas. • Implementación de la técnica de carga gradual para la mejora de eficiencia de conversores dc-dc a capacitores conmutados. • Simplificación de la técnica de carga gradual para mejora de la eficiencia en algunas arquitecturas de conversores dc-dc de capacitores conmutados. • Análisis del mínimo voltaje de operación en circuitos digitales debido al ruido intrínseco del dispositivo y el impacto del escalado de las tecnologías en el mismo. • Mejoras en el modelado del punto de energía mínima de operación de un circuito digital en el cual se consideran las diferencias entre el transistor PMOS y NMOS. • Demostración de la existencia de un óptimo en la relación entre las corrientes de fuga entre el NMOS y PMOS que minimiza la energía de fugas consumida en la región sub umbral. • Desarrollo de una estrategia de polarización del voltaje de puerta trasera para que el circuito digital trabaje en el óptimo antes mencionado. • Desarrollo de una estrategia para el dimensionado de los transistores que componen las compuertas digitales que permite al circuito digital operar en el óptimo antes mencionado. • Análisis del impacto de la arquitectura del circuito y de los datos de entrada del mismo en el óptimo antes mencionado

    A Study on Energy-Efficient Inductor Current Controls for Maximum Energy Delivery in Battery-free Buck Converter

    Get PDF
    학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2017. 2. 김재하.A discontinuous conduction mode (DCM) buck converter, which acts as a voltage regulator in battery-free applications, is proposed to maximize the ener-gy delivery to the load system. In this work, we focus the energy loss problem during start-up and steady-state operation of the buck converter, which severely limits the energy delivery. Especially, the energy loss problem arises from the fact that there is no constant power source such as a battery and the only a small amount of energy harvested from the ambient energy sources is available. To address such energy loss problem, this dissertation proposes optimal induc-tor current control techniques at each operation to greatly reduce the energy losses. First, a switching-based stepwise capacitor charging scheme is presented that can charge the output capacitor with constant inductor current during start-up operation. By switching the inductor with gradually incrementing duty-cycle ratios in a stepwise fashion, the buck converter can make the inductor current a constant current source, which can greatly reduce the start-up energy loss com-pared to that in the conventional capacitor charging scheme with a voltage source. Second, a variable on-time (VOT) pulse-frequency-modulation (PFM) scheme is presented that can keep the peak inductor current constant during steady-state operation. By adaptively varying the on-time according to the op-erating voltage conditions of the buck converter, it can suppress the voltage ripple and improve the power efficiency even with a small output capacitor. Third, an adaptive off-time positioning zero-crossing detector (AOP-ZCD) is presented that can adaptively position the turn-off timing of the low-side switch close to the zero-inductor-current timing by predicting the inductor current waveform without using a power-hungry continuous-time ZCD. To demonstrate the proposed design concepts, the prototype battery-free wireless remote switch including the piezoelectric energy harvester and the proposed buck converter was fabricated in a 250 nm high-voltage CMOS technology. It can harvest a total energy of 246 μJ from a single button press action of a 300-mm2 lead magnesium niobate-lead titanate (PMN-PT) piezoelectric disc, and deliver more than 200 μJ to the load, which is sufficient to transmit a 4-byte-long message via 2.4-GHz wireless USB channel over a 10-m distance. If such battery-free application does not use the proposed buck converter, the energy losses in-curred at the buck converter would be larger than the energy harvested, and therefore it cannot operate with a single button-pressing action. Furthermore, thanks to the proposed energy efficient buck converter, the battery-free wire-less remote switch can be realized by using a cheaper PZT piezoelectric source, which can achieve a 10× cost reduction.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS CONTRIBUTION AND ORGANIZATION 6 CHAPTER 2 OPERATION MODE AND OVERALL ARCHITECTURE 8 2.1 TOPOLOGY SELECTION 8 2.2 PRINCIPLE OF OPERATION 11 2.2.1 BASIC OPERATION IN CCM 12 2.2.2 BASIC OPERATION IN DCM 15 2.3 OPERATION MODE 17 2.4 OVERALL ARCHITECTURE 19 CHAPTER 3 OPTIMAL INDUCTOR CURRENT CONTROLS FOR MAXIMUM ENERGY DELIVERY 23 3.1 CONSTANT INDUCTOR CURRENT CONTROL WITH SWITCHING-BASED STEPWISE CAPACITOR CHARGING SCHEME 24 3.1.1 CONVENTIONAL CHARGING SCHEME WITH A SWITCH 24 3.1.2 ADIABATIC STEPWISE CHARGING 27 3.1.3 PROPOSED START-UP SCHEME 29 3.2 CONSTANT INDUCTOR PEAK CURRENT CONTROL WITH VARIABLE ON-TIME PFM SCHEME 35 3.2.1 BASIC OPERATION OF PFM BUCK CONVERTER 35 3.2.2 CONSTANT ON-TIME PFM SCHEME 39 3.2.3 VARIABLE ON-TIME PFM SCHEME 41 3.3 INDUCTOR CURRENT PREDICTION WITH ADAP-TIVE OFF-TIME POSITIONING ZCD (AOP-ZCD) 44 3.3.1 PREVIOUS SAMPLING-BASED ZCD 44 3.3.2 PROPOSED ADAPTIVE OFF-TIME POSITIONING ZCD 47 CHAPTER 4 CIRCUIT IMPLEMENTATION 49 4.1 CIRCUIT IMPLEMENTATION OF SWITCHING-BASED STEPWISE CAPACITOR CHARGER 49 4.1.1 VOLTAGE DETECTOR (VD) 50 4.1.2 DIGITAL PULSE WIDTH MODULATOR (DPWM) 52 4.1.3 PROGRAMMABLE DUTY-CYCLE CONTROLLER (DCC) 55 4.1.4 SWITCHED CAPACITOR (SC) STEP-DOWN CONVERTER 57 4.2 CIRCUIT IMPLEMENTATION OF VARIABLE ON-TIME PULSE GENERATOR 59 4.3 CIRCUIT IMPLEMENTATION OF ADAPTIVE OFF-TIME POSITIONING ZCD 64 4.3.1 ADAPTIVE OFF-TIME (AOT) PULSE GENERATOR 64 4.3.2 TIMING ERROR DETECTOR AND SHIFT-REGISTER 68 CHAPTER 5 MEASUREMENT RESULTS OF PROPOSED BUCK CONVERTER 70 5.1 SWITCHING-BASED STEPWISE CAPACITOR CHARGER 71 5.2 STEADY-STATE PERFORMANCE WITH VOT PULSE GENERATOR AND AOP-ZCD 74 CHAPTER 6 REALIZATION OF BATTERY-FREE WIRELESS REMOTE SWITCH 84 6.1 KEY BUILDING BLOCKS OF BATTERY-FREE WIRELESS REMOTE SWITCH 85 6.2 PIEZOELECTRIC ENERGY HARVESTER WITH P-SSHI RECTIFIER 86 6.2.1 ANALYSIS ON SINGLE-PULSED ENERGY HARVESTING 88 6.2.2 PROPOSED PIEZOELECTRIC ENERGY HARVESTER 91 6.2.3 CIRCUIT IMPLEMENTATION 93 6.3 MEASUREMENT RESULTS OF BATTERY-FREE WIRELESS SWITCH 96 CHAPTER 7 CONCLUSION 101 BIBLIOGRAPHY 103 초 록 110Docto

    Development of Robust and Dynamic Control Solutions for Energy Storage Enabled Hybrid AC/DC Microgrids

    Get PDF
    Development of Robust and Dynamic Control Solutions for Energy Storage Enabled Hybrid AC/DC Microgrid

    Developing Energy Harvest Efficient Strategies with Microbial Fuel Cells

    Get PDF
    Nowadays, thinking of energetic efficiency is to determine how to decrease consumption and to reuse resources. This is a major concern when addressing hydric resources. The consumption of drinking water is seeing an unaffordable growth and, although most of it is replenished to the environment, the water quality is affected by pollutants and impurities. As such, using wastewater, a by-product of our routine and way of life, as resource is an asset. Even more when thinking about the heightened energy costs of a wastewater treatment station. The hypotheses of this work show how to achieve this goal by using microbial fuel cells. The organic composition of this water increases its energy production potential, where the bacterial metabolism can be used to, simultaneously, produce energy and help to clean the water. This document is divided in 5 chapters. The strategic positioning of the theme happens in chapter 1. Chapter 2 explains how the main elements of microbial fuel cell technology can work and determine its operation. In chapter 3, the power management systems used with microbial fuel cells are presented and discussed, with the identification of optimization strategies. The second-to-last chapter corresponds to the experimental results discussion and validation, while focusing improved energy production efficiencies. The outputs of this chapter pilot the future work analysis on chapter 5, together with the main conclusions and research trends. The validity and usefulness of this work is cleared with an application example.Pensar em economia energética é, hoje, considerar soluções para a redução de consumo e reutilização de recursos. Esta preocupação é importante ao examinar a utilização dos recursos hídricos. O consumo de água potável está a crescer insustentavelmente e, apesar de grande parte desse consumo ser restituído ao meio ambiente, a qualidade da água é afetada por poluentes ou impurezas. A utilização de água residual, um produto da nossa rotina e qualidade de vida, como um recurso é, por isso, uma mais valia. É ainda mais evidente ao considerar os elevados consumos energéticos de uma estação de tratamento de água residual. As hipóteses abordadas neste trabalho mostram como é possível atingir este objetivo usando células microbianas de combustível. A composição orgânica desta água faz com que o seu potencial energético possa ser explorado, usando o metabolismo bacteriano para produzir energia e, simultaneamente, auxiliar na limpeza da água. Este documento está dividido em 5 capítulos. O posicionamento do tema ocorre no capítulo 1. O capítulo 2 observa os principais elementos da tecnologia das células microbianas de combustível, permitindo compreender o seu funcionamento e conhecer que variáveis afetam o seu funcionamento. No capítulo 3 são apresentadas as tipologias de abordagem à gestão energética para esta pilha bacteriológica, discutindo-se as vantagens e otimizações de cada sistema. O penúltimo capítulo corresponde à exploração de resultados experimentais e à validação de hipóteses, orientadas para a maior eficiência energética. Surgem assim recomendações que servirão para guiar os trabalhos futuros, discutidos no capítulo final. Este, o capítulo 5, conta ainda com a apresentação das principais conclusões e das tendências de pesquisa. O trabalho termina com um exemplo de aplicação que solidifica a validade e utilidade da aplicação desta tecnologia

    Robustness and durability aspects in the design of power management circuits for IoT applications

    Get PDF
    With the increasing interest in the heterogeneous world of the “Internet of Things” (IoT), new compelling challenges arise in the field of electronic design, especially concerning the development of innovative power management solutions. Being this diffusion a consolidated reality nowadays, emerging needs like lifetime, durability and robustness are becoming the new watchwords for power management, being a common ground which can dramatically improve service life and confidence in these devices. The possibility to design nodes which do not need external power supply is a crucial point in this scenario. Moreover, the development of autonomous nodes which are substantially maintenance free, and which therefore can be placed in unreachable or harsh environments is another enabling aspect for the exploitation of this technology. In this respect, the study of energy harvesting techniques is increasingly earning interest again. Along with efficiency aspects, degradation aspects are the other main research field with respect to lifetime, durability and robustness of IoT devices, especially related to aging mechanisms which are peculiar in power management and power conversion circuits, like for example battery wear during usage or hot-carrier degradation (HCD) in power MOSFETs. In this thesis different aspects related to lifetime, durability and robustness in the field of power management circuits are studied, leading to interesting contributions. Innovative designs of DC/DC power converters are studied and developed, especially related to reliability aspects of the use of electrochemical cells as power sources. Moreover, an advanced IoT node is proposed, based on energy harvesting techniques, which features an intelligent dynamically adaptive power management circuit. As a further contribution, a novel algorithm is proposed, which is able to effectively estimate the efficiency of a DC/DC converter for photovoltaic applications at runtime. Finally, an innovative DC/DC power converter with embedded monitoring of hot-carrier degradation in power MOSFETs is designed

    Industrial and Technological Applications of Power Electronics Systems

    Get PDF
    The Special Issue "Industrial and Technological Applications of Power Electronics Systems" focuses on: - new strategies of control for electric machines, including sensorless control and fault diagnosis; - existing and emerging industrial applications of GaN and SiC-based converters; - modern methods for electromagnetic compatibility. The book covers topics such as control systems, fault diagnosis, converters, inverters, and electromagnetic interference in power electronics systems. The Special Issue includes 19 scientific papers by industry experts and worldwide professors in the area of electrical engineering

    Applications of Power Electronics:Volume 2

    Get PDF

    Towards self-powered wireless sensor networks

    Get PDF
    Ubiquitous computing aims at creating smart environments in which computational and communication capabilities permeate the word at all scales, improving the human experience and quality of life in a totally unobtrusive yet completely reliable manner. According to this vision, an huge variety of smart devices and products (e.g., wireless sensor nodes, mobile phones, cameras, sensors, home appliances and industrial machines) are interconnected to realize a network of distributed agents that continuously collect, process, share and transport information. The impact of such technologies in our everyday life is expected to be massive, as it will enable innovative applications that will profoundly change the world around us. Remotely monitoring the conditions of patients and elderly people inside hospitals and at home, preventing catastrophic failures of buildings and critical structures, realizing smart cities with sustainable management of traffic and automatic monitoring of pollution levels, early detecting earthquake and forest fires, monitoring water quality and detecting water leakages, preventing landslides and avalanches are just some examples of life-enhancing applications made possible by smart ubiquitous computing systems. To turn this vision into a reality, however, new raising challenges have to be addressed, overcoming the limits that currently prevent the pervasive deployment of smart devices that are long lasting, trusted, and fully autonomous. In particular, the most critical factor currently limiting the realization of ubiquitous computing is energy provisioning. In fact, embedded devices are typically powered by short-lived batteries that severely affect their lifespan and reliability, often requiring expensive and invasive maintenance. In this PhD thesis, we investigate the use of energy-harvesting techniques to overcome the energy bottleneck problem suffered by embedded devices, particularly focusing on Wireless Sensor Networks (WSNs), which are one of the key enablers of pervasive computing systems. Energy harvesting allows to use energy readily available from the environment (e.g., from solar light, wind, body movements, etc.) to significantly extend the typical lifetime of low-power devices, enabling ubiquitous computing systems that can last virtually forever. However, the design challenges posed both at the hardware and at the software levels by the design of energy-autonomous devices are many. This thesis addresses some of the most challenging problems of this emerging research area, such as devising mechanisms for energy prediction and management, improving the efficiency of the energy scavenging process, developing protocols for harvesting-aware resource allocation, and providing solutions that enable robust and reliable security support. %, including the design of mechanisms for energy prediction and management, improving the efficiency of the energy harvesting process, the develop of protocols for harvesting-aware resource allocation, and providing solutions that enable robust and reliable security support

    Wind Power

    Get PDF
    This book is the result of inspirations and contributions from many researchers of different fields. A wide verity of research results are merged together to make this book useful for students and researchers who will take contribution for further development of the existing technology. I hope you will enjoy the book, so that my effort to bringing it together for you will be successful. In my capacity, as the Editor of this book, I would like to thanks and appreciate the chapter authors, who ensured the quality of the material as well as submitting their best works. Most of the results presented in to the book have already been published on international journals and appreciated in many international conferences
    corecore