Operational Trans-Resistance Amplifier Based Tunable Wave Active Filter

In this paper, Operational Trans-Resistance Amplifier (OTRA) based wave active filter structures are presented. They are flexible and modular, making them suitable to implement higher order filters. The circuits implement the resistors using matched transistors, operating in linear region, making them well suited for IC fabrication. They are insensitive to parasitic input capacitances and input resistances due to the internally grounded input terminals of OTRA. As an application, a doubly terminated third order Butterworth low pass filter has been implemented, by substituting OTRA based wave equivalents of passive elements. PSPICE simulations are given to verify the theoretical analysis

Log-domain electronically-tuneable fully differential high order multi-function filter

This paper presents the synthesis of fully deferential circuit that is capable of performing simultaneous high-pass, low-pass, and band-pass filtering in the log domain. The circuit utilizes modified Seevinck’s integrators in the current mode. The transfer function describing the filter is first presented in the form of a canonical signal flow graph through applying Mason’s gain formula. The resulting signal flow graph consists of summing points and pick-off points associated with current mode integrators within unity-gain negative feedback loops. The summing points and the pick-off points are then synthesized as simple nodes and current mirrors, respectively. A new fully differential current-mode integrator circuit is proposed to realize the integration operation. The proposed integrator uses grounded capacitors with no resistors and can be adjusted to work as either lossless or lossy integrator via tuneable current sources. The gain and the cutoff frequency of the integrator are adjustable via biasing currents. Detailed design and simulation results of an example of a 5th order filter circuit is presented. The proposed circuit can perform simultaneously 5th order low-pass filtering, 5th order high-pass filtering, and 4th order band-pass filtering. The simulation is performed using Pspice with practical Infineon BFP649 BJT model. Simulation results show good matching with the target

Novel Floating General Element Simulators Using CBTA

In this study, a novel floating frequency dependent negative resistor (FDNR), floating inductor, floating capacitor and floating resistor simulator circuit employing two CBTAs and three passive components is proposed. The presented circuit can realize floating FDNR, inductor, capacitor or resistor depending on the passive component selection. Since the passive elements are all grounded, this circuit is suitable for fully integrated circuit design. The circuit does not require any component matching conditions, and it has a good sensitivity performance with respect to tracking errors. Moreover, the proposed FDNR, inductance, capacitor and resistor simulator can be tuned electronically by changing the biasing current of the CBTA or can be controlled through the grounded resistor or capacitor. The high-order frequency dependent element simulator circuit is also presented. Depending on the passive component selection, it realizes high-order floating circuit defining as V(s) = snAI(s) or V(s) = s-nBI(s). The proposed floating FDNR simulator circuit and floating high-order frequency dependent element simulator circuit are demonstrated by using PSPICE simulation for 0.25 μm, level 7, TSMC CMOS technology parameters

Unconventional Circuit Elements for Ladder Filter Design

Kmitočtové filtry jsou lineární elektrické obvody, které jsou využívány v různých oblastech elektroniky. Současně tvoří základní stavební bloky pro analogové zpracování signálů. V poslední dekádě bylo zavedeno množství aktivních stavebních bloků pro analogové zpracování signálů. Stále však existuje potřeba vývoje nových aktivních součástek, které by poskytovaly nové možnosti a lepší parametry. V práci jsou diskutovány různé aspekty obvodů pracujících v napěťovém, proudovém a smíšném módu. Práce reaguje na dnešní potřebu nízkovýkonových a nízkonapěťových aplikací pro přenosné přístroje a mobilní komunikační systémy a na problémy jejich návrhu. Potřeba těchto výkonných nízkonapěťových zařízení je výzvou návrhářů k hledání nových obvodových topologií a nových nízkonapěťových technik. V práci je popsána řada aktivních prvků, jako například operační transkonduktanční zesilovač (OTA), proudový konvejor II. generace (CCII) a CDTA (Current Differencing Transconductance Amplifier). Dále jsou navrženy nové prvky, jako jsou VDTA (Voltage Differencing Transconductance Amplifier) a VDVTA (Voltage Differencing Voltage Transconductance Amplifier). Všechny tyto prvky byly rovněž implementovány pomocí "bulk-driven" techniky CMOS s cílem realizace nízkonapěťových aplikací. Tato práce je rovněž zaměřena na náhrady klasických induktorů syntetickými induktory v pasivních LC příčkových filtrech. Tyto náhrady pak mohou vést k syntéze aktivních filtrů se zajímavými vlastnostmi.Frequency filters are linear electric circuits that are used in wide area of electronics. They are also the basic building blocks in analogue signal processing. In the last decade, a huge number of active building blocks for analogue signal processing was introduced. However, there is still the need to develop new active elements that offer new possibilities and better parameters. The current-, voltage-, or mixed-mode analog circuits and their various aspects are discussed in the thesis. This work reflects the trend of low-power (LP) low-voltage (LV) circuits for portable electronic and mobile communication systems and the problems of their design. The need for high-performance LV circuits encourages the analog designers to look for new circuit architectures and new LV techniques. This thesis presents various active elements such as Operational Transconductance Amplifier (OTA), Current Conveyor of Second Generation (CCII), and Current Differencing Transconductance Amplifier (CDTA), and introduces novel ones, such as Voltage Differencing Transconductance Amplifier (VDTA) and Voltage Differencing Voltage Transconductance Amplifier (VDVTA). All the above active elements were also designed in CMOS bulk-driven technology for LP LV applications. This thesis is also focused on replacement of conventional inductors by synthetic ones in passive LC ladder filters. These replacements can lead to the synthesis of active filters with interesting parameters.

Realization of Integrable Low- Voltage Companding Filters for Portable System Applications

Undoubtedly, today’s integrated electronic systems owe their remarkable performance primarily to the rapid advancements of digital technology since 1970s. The various important advantages of digital circuits are: its abstraction from the physical details of the actual circuit implementation, its comparative insensitiveness to variations in the manufacturing process, and the operating conditions besides allowing functional complexity that would not be possible using analog technology. As a result, digital circuits usually offer a more robust behaviour than their analog counterparts, though often with area, power and speed drawbacks. Due to these and other benefits, analog functionality has increasingly been replaced by digital implementations. In spite of the advantages discussed above, analog components are far from obsolete and continue to be key components of modern electronic systems. There is a definite trend toward persistent and ubiquitous use of analog electronic circuits in day-to-day life. Portable electronic gadgets, wireless communications and the widespread application of RF tags are just a few examples of contemporary developments. While all of these electronic systems are based on digital circuitry, they heavily rely on analog components as interfaces to the real world. In fact, many modern designs combine powerful digital systems and complementary analog components on a single chip for cost and reliability reasons. Unfortunately, the design of such systems-on-chip (SOC) suffers from the vastly different design styles of analog and digital components. While mature synthesis tools are readily available for digital designs, there is hardly any such support for analog designers apart from wellestablished PSPICE-like circuit simulators. Consequently, though the analog part usually occupies only a small fraction of the entire die area of an SOC, but its design often constitutes a major bottleneck within the entire development process. Integrated continuous-time active filters are the class of continuous-time or analog circuits which are used in various applications like channel selection in radios, anti-aliasing before sampling, and hearing aids etc. One of the figures of merit of a filter is the dynamic range; this is the ratio of the largest to the smallest signal that can be applied at the input of the filter while maintaining certain specified performance. The dynamic range required in the filter varies with the application and is decided by the variation in strength of the desired signal as well as that of unwanted signals that are to be rejected by the filter. It is well known that the power dissipation and the capacitor area of an integrated active filter increases in proportion to its dynamic range. This situation is incompatible with the needs of integrated systems, especially battery operated ones. In addition to this fundamental dependence of power dissipation on dynamic range, the design of integrated active filters is further complicated by the reduction of supply voltage of integrated circuits imposed by the scaling down of technologies to attain twin objective of higher speed and lower power consumption in digital circuits. The reduction in power consumption with decreasing supply voltage does not apply to analog circuits. In fact, considerable innovation is required with a reduced supply voltage even to avoid increasing power consumption for a given signal to noise ratio (S/N). These aspects pose a great hurdle to the active filter designer. A technique which has attracted the attention of circuit designers as a possible route to filters with higher dynamic range per unit power consumption is “companding”. Companding (compression-expansion) filters are a very promising subclass of continuous-time analog filters, where the input (linear) signal is initially compressed before it will be handled by the core (non-linear) system. In order to preserve the linear operation of the whole system, the non-linear signal produced by the core system is converted back to a linear output signal by employing an appropriate output stage. The required compression and expansion operations are performed by employing bipolar transistors in active region or MOS transistors in weak inversion; the systems thus derived are known as logarithmic-domain (logdomain) systems. In case MOS transistors operated in saturation region are employed, the derived structures are known as Square-root domain systems. Finally, the third class of companding filters can also be obtained by employing bipolar transistors in active region or MOS transistors in weak inversion; the derived systems are known as Sinh-domain systems. During the last several years, a significant research effort has been already carried out in the area of companding circuits. This is due to the fact that their main advantages are the capability for operation in low-voltage environment and large dynamic range originated from their companding nature, electronic tunability of the frequency characteristics, absence of resistors and the potential for operations in varied frequency regions.Thus, it is obvious that companding filters can be employed for implementing high-performance analog signal processing in diverse frequency ranges. For example, companding filters could be used for realizing subsystems in: xDSL modems, disk drive read channels, biomedical electronics, Bluetooth/ZigBee applications, phaselocked loops, FM stereo demodulator, touch-tone telephone tone decoder and crossover network used in a three-way high-fidelity loudspeaker etc. A number of design methods for companding filters and their building blocks have been introduced in the literature. Most of the proposed filter structures operate either above 1.5V or under symmetrical (1.5V) power supplies. According to data that provides information about the near future of semiconductor technology, International Technology Roadmap for Semiconductors (ITRS), in 2013, the supply voltage of digital circuits in 32 nm technology will be 0.5 V. Therefore, the trend for the implementation of analog integrated circuits is the usage of low-voltage building blocks that use a single 0.5-1.5V power supply. Therefore, the present investigation was primarily concerned with the study and design of low voltage and low power Companding filters. The work includes the study about: the building blocks required in implementing low voltage and low power Companding filters; the techniques used to realize low voltage and low power Companding filters and their various areas of application. Various novel low voltage and low power Companding filter designs have been developed and studied for their characteristics to be applied in a particular portable area of application. The developed designs include the N-th order universal Companding filter designs, which have been reported first time in the open literature. Further, an endeavor has been made to design Companding filters with orthogonal tuning of performance parameters so that the designs can be simultaneously used for various features. The salient features of each of the developed circuit are described. Electronic tunability is one of the major features of all of the designs. Use of grounded capacitors and resistorless designs in all the cases makes the designs suitable for IC technology. All the designs operate in a low-voltage and low-power environment essential for portable system applications. Unless specified otherwise, all the investigations on these designs are based on the PSPICE simulations using model parameters of the NR100N bipolar transistors and BSIM 0.35μm/TSMC 0.25μm /TSMC 0.18μm CMOS process MOS transistors. The performance of each circuit has been validated by comparing the characteristics obtained using simulation with the results present in the open literature. The proposed designs could not be realized in silicon due to non-availability of foundry facility at the place of study. An effort has already been started to realize some of the designs in silicon and check their applicability in practical circuits. At the basic level, one of the proposed Companding filter designs was implemented using the commercially available transistor array ICs (LM3046N) and was found to verify the theoretical predictions obtained from the simulation results

Nonlinearity and noise modeling of operational transconductance amplifiers for continuous time analog filters

A general framework for performance optimization of continuous-time OTA-C (Operational Transconductance Amplifier-Capacitor) filters is proposed. Efficient procedures for evaluating nonlinear distortion and noise valid for any filter of arbitrary order are developed based on the matrix description of a general OTA-C filter model . Since these procedures use OTA macromodels, they can be used to obtain the results significantly faster than transistor-level simulation. In the case of transient analysis, the speed-up may be as much as three orders of magnitude without almost no loss of accuracy. This makes it possible to carry out direct numerical optimization of OTA-C filters with respect to important characteristics such as noise performance, THD, IM3, DR or SNR. On the other hand, the general OTA-C filter model allows us to apply matrix transforms that manipulate (rescale) filter element values and/or change topology without changing its transfer function. The above features are a basis to build automated optimization procedures for OTA-C filters. In particular, a systematic optimization procedure using equivalence transformations is proposed. The research also proposes suitable software implementations of the optimization process. The first part of the research proposes a general performance optimization procedure and to verify the process two application type examples are mentioned. An application example of the proposed approach to optimal block sequencing and gain distribution of 8th order cascade Butterworth filter (for two variants of OTA topologies) is given. Secondly the modeling tool is used to select the best suitable topology for a 5th order Bessel Low Pass Filter. Theoretical results are verified by comparing to transistor-level simulation withCADENCE. For the purpose of verification, the filters have also been fabricated in standard 0.5mm CMOS process. The second part of the research proposes a new linearization technique to improve the linearity of an OTA using an Active Error Feedforward technique. Most present day applications require very high linear circuits combined with low noise and low power consumption. An OTA based biquad filter has also been fabricated in 0.35mm CMOS process. The measurement results for the filter and the stand alone OTA have been discussed. The research focuses on these issues

Automatic Synthesis of VLSI Layout for CMOS Continuous-Time Filters

Automatic synthesis of digital VLSI layout has been available for many years. It has become a necessary part of the design industry as the window of time from conception to production shrinks with ever increasing competition. However, automatic synthesis of analog VLSI layout remains rare. With digital circuits, there is often room for signal drift. In a digital circuit, a signal can drift within a range before hitting the threshold which triggers a change in logic state. The effect of parasitic capacitances for the most part, hinders the timing margins of the signal, but not its functionality. The logic functionality is protected by the inherent noise immunity of digital circuits. With analog circuits, however, there is little room for signal drift. Parasitic directly influence signal integrity and the functionality of the circuit. The underlying problem, that the automatic VLSI layout programs face, is how to minimize this influence. This thesis describes a software tool that was written to show that the minimization of parasitic influence is possible in the case of automatic layout of continuous-time filters using transconductance-capacitor methods

Realization of analog signal processing modules using carbon nanotube field effect transistors

This thesis presents the realization and performance analysis of several carbon nanotube field effect transistor (CNTFET) based analog signal processing (ASP) modules. CNTFET is predicted as a possible successor to conventional silicon complementary metal oxide semiconductor (CMOS), which has reached its scaling limits. The CMOS based ASP modules face significant challenges at deep nanoscale, resulting in severe performance degradations due to short channel effects. The main goal of this work is to realize CNTFET active building blocks (ABBs), and then to utilize these ABBs for realization of low-voltage, low-power, and high-frequency ASP modules. The proposed ABBs have low power dissipation, reduced parasitic components, and minimum number of CNTFETs. The proposed modules are active inductor (AI), first-order phase shifter, and second-order phase shifter. This research proposes a new CNTFET based grounded AI (GAI) circuit with high self-resonance frequency (SRF), wide tunable inductance range, and high quality factor. Simulation results demonstrate that the GAI offers tunable inductance from 4.4 nH to 287.4 nH with a maximum SRF of 101 GHz. It consumes very low power dissipation of 0.337 mW. In comparison to high performance available GAI circuits, the proposed GAI shows 34% reduction in power dissipation and nine times higher SRF. A highfrequency low-noise amplifier (LNA) circuit is also designed by utilizing the proposed GAI to showcase its application. The simulation result shows high frequency bandwidth of 17.5 GHz to 57 GHz, 15.9 dB maximum voltage gain, better than -10 dB input matching, and less than 3 dB noise figure. This research also proposes a compact wideband first-order phase shifter (FOPS) and active-only FOPS (AOFOPS). Simulation results demonstrate the FOPS has a tunable pole frequency range between 1.913 GHz and 40.2 GHz, input and output voltage noises of 4.402 nV/VHz and 4.414 nV/VH z respectively, and power dissipation of 0.4862 mW. The AOFOPS circuit also offers a wide tunable range of pole frequency between 34.2 GHz to 56.4 GHz with input noise and output noise of 6.822 nV/VHz and 6.761 nV/VHz respectively, and power dissipation of only 0.0338 mW. The AOFOPS dissipates 12.40 times less power in comparison to state-of-art FOPS circuits. This work also proposes active-only second-order phase shifter. The proposed circuit provides a tunable pole frequency between 16.2 GHz to 42.5 GHz, with input and output noises of 21.698 nV/VHz and 21.593 nV/VHz respectively, while consuming 0.2256 mW power. All circuit performances are verified through HSPICE simulation by utilizing the Stanford CNTFET model at 16 nm technology node with supply voltage of 0.7 V

Biomimetic cochlea filters : from modelling, design to analogue VLSI implementation

This thesis presents a novel biomimetic cochlea filter which closely resembles the biological cochlea behaviour. The filter is highly feasible for analogue very-large-scale integration (VLSI) circuits, which leads to a micro-watt-power and millimetre-sized hardware implementation. By virtue of such features, the presented filter contributes to a solid foundation for future biologically-inspired audio signal processors. Unlike existing works, the presented filter is developed by taking direct inspirations from the physiologically measured results of the biological cochlea. Since the biological cochlea has prominently different characteristics of frequency response from low to high frequencies, the biomimetic cochlea filter is built by cascading three sub-filters accordingly: a 2nd-order bandpass filter for the constant gentle low-frequency response, a 2nd-order tunable low-pass filter for the variable and selective centre frequency response and a 5th-order elliptic filter for the ultra-steep roll-off at stop-band. As a proof of concept, a biomimetic cochlea filter bank is built to process audio signals, which demonstrates the highly discriminative spectral decomposition and high-resolution time-frequency analysis capabilities similar to the biological cochlea. The filter has simple representation in the Laplace domain which leads to a convenient analogue circuit realisation. A floating-active-inductor circuit cell is developed to build the corresponding RLC ladder for each of the three sub-filters. The circuits are designed based on complementary metal-oxide-semiconductor (CMOS) transistors for VLSI implementation. Non-ideal factors of CMOS transistors including parasitics, noise and mismatches are extensively analysed and consciously considered in the circuit design. An analogue VLSI chip is successfully fabricated using 0.35μ m CMOS process. The chip measurements demonstrate that the centre frequency response of the filter has about 20 dB wide gain tuning range and a high quality factor reaching maximally over 19. The filter has a 20 dB/decade constant gentle low-frequency tail and an over 300 dB/decade sharp stop-band roll-off slope. The measured results agree with the filter model expectations and are comparable with the biological cochlea characteristics. Each filter channel consumes as low as 59.5 ~90μ Wpower and occupies only 0.9 mm2 area. Besides, the biomimetic cochlea filter chip is characterised from a wide range of angles and the experimental results cover not only the auditory filter specifications but also the integrated circuit design considerations. Furthermore, following the progressive development of the acoustic resonator based on microelectro- mechanical systems (MEMS) technology, a MEMS-CMOS implementation of the proposed filter becomes possible in the future. A key challenge for such implementation is the low sensing capacitance of the MEMS resonator which suffers significantly from sensitivity degradation due to the parasitic capacitance. A novel MEMS capacitive interface circuit chip is additionally developed to solve this issue. As shown in the chip results, the interface circuit is able to cancel the parasitic capacitance and increase the sensitivity of capacitive sensors by 35 dB without consuming any extra power. Besides, the chopper-stabilisation technique is employed which effectively reduces the circuit flicker noise and offsets. Due to these features, the interface circuit chip is capable of converting a 7.5 fF capacitance change of a 1-Volt-biased 0.5 pF capacitive sensor pair into a 0.745 V signal-conditioned output while consuming only 165.2μ W power

Modern VLSI Analogue Filter Design: Methodology and Software Development

This thesis describes various approaches for the design of modern analogue filters and provides a practical filter and equaliser design aids system XFILT. The thesis begins by placing the analogue filter design technique and software into a historical and technology perspective. The evolution of the analogue filter is traced from early work, through the passive-RLC to transconductor-C and switched-current realisations. The software development in VLSI analogue filter automation is reviewed. For SC filter design, a cascade SC design approach which includes a novel pole-zero pairing method and a comprehensive comparison of SC filter realisation using different biquads are presented. Very useful guidelines for the choice of a suitable biquad structure according to the nature of the filter problem are presented. The canonical realisations of SC filter are studied. The multirate SC system design is described. Several strategies and the algorithms for multirate SC system design are proposed. In transconductor-C filter design research, the definition of a canonical ladder based transconductor-C filter is introduced, and two canonical ladder based transconductor-C filter design approaches are proposed. The ladder based transconductor-C equaliser design is also discussed. A practical video frequency transconductor-C filter and equaliser design is given to demonstrate the utility of the matrix design method and the design software. A new approach to realise exact ladder based SI filter with first and second generation memory cell has been proposed. The bilinear transformation is used in the design procedure. Eight different SI ladder based structures can be obtained for one prototype ladder. Therefore it provides SI filter designers with various circuit choices based on different requirement such as area, maximum ratio of transistor aspect ratio limit, sensitivity or noise performance. Techniques to improve dynamic range and reduce circuit parameter spread are also presented. The proposed approach is well suited for a computer compiler implementation. A suitability study of each decomposition method for different filtering applications is also carried out and a general guideline for the choice of different decomposition methods is obtained. A comparison study on SI filter sensitivity performance based on first generation and second generation memory cells is carried out. Using four filter examples, it is demonstrated that SI filters based on a second generation SI memory cell have good sensitivity performance. For SI filters based on first generation memory cells, it is shown that a high ratio of clock frequency to cutoff frequency in the lowpass case, or a high ratio of clock frequency to midband frequency in the bandpass case would introduce high sensitivity. A novel approach for SI ladder filter based on the S2I integrator is also proposed and a canonical realisation for SI filter based on S2I integrator is developed. Examination of SI equaliser design reveals that cascade structure is a better candidate than ladder based structure. Multirate SI filter system design is also studied. Finally, a very brief introduction to the assembly of the design methods in this thesis into a software package XHLT for VLSI analogue filter and equaliser design is given. The user aspects of XFILT have been discussed and various capabilities of XFILT are demonstrated. Several advanced facilities which remove traditional design limitations are illustrated. The philosophy of the system is explained. It is shown that the distinguished features of XFILT are Ease of Use. General Applicability, and Ease of Extension. The system structure is described and the graphics interface which acts both as user friendly interface and a system manager of all the software is outlined. Fabricated SC, transconductor-C, and SI filter and equaliser have been designed by using XFILT. The system is under further enhancement toward a commercial product