End-of-Life and Constant Rate Reliability Modeling for Semiconductor Packages Using Knowledge-Based Test Approaches

End-of-life and constant rate reliability modeling for semiconductor packages are the focuses of this dissertation. Knowledge-based testing approaches are applied and the test-to-failure approach is approved to be a reliable approach. First of all, the end-of-life AF models for solder joint reliability are studied. The research results show using one universal AF model for all packages is flawed approach. An assessment matrix is generated to guide the application of AF models. The AF models chosen should be either assessed based on available data or validated through accelerated stress tests. A common model can be applied if the packages have similar structures and materials. The studies show that different AF models will be required for SnPb solder joints and SAC lead-free solder joints. Second, solder bumps under power cycling conditions are found to follow constant rate reliability models due to variations of the operating conditions. Case studies demonstrate that a constant rate reliability model is appropriate to describe non solder joint related semiconductor package failures as well. Third, the dissertation describes the rate models using Chi-square approach cannot correlate well with the expected failure mechanisms in field applications. The estimation of the upper bound using a Chi-square value from zero failure is flawed. The dissertation emphasizes that the failure data is required for the failure rate estimation. A simple but tighter approach is proposed and provides much tighter bounds in comparison of other approaches available. Last, the reliability of solder bumps in flip chip packages under power cycling conditions is studied. The bump materials and underfill materials will significantly influence the reliability of the solder bumps. A set of comparable bump materials and the underfill materials will dramatically improve the end-of-life solder bumps under power cycling loads, and bump materials are one of the most significant factors. Comparing to the field failure data obtained, the end-of-life model does not predict the failures in the field, which is more close to an approximately constant failure rate. In addition, the studies find an improper underfill material could change the failure location from solder bump cracking to ILD cracking or BGA solder joint failures

MICROSTRUCTURAL CHARACTERIZATION AND THERMAL CYCLING RELIABILITY OF SOLDERS UNDER ISOTHERMAL AGING AND ELECTRICAL CURRENT

Solder joints on printed circuit boards provide electrical and mechanical connections between electronic devices and metallized patterns on boards. These solder joints are often the cause of failure in electronic packages. Solders age under storage and operational life conditions, which can include temperature, mechanical loads, and electrical current. Aging occurring at a constant temperature is called isothermal aging. Isothermal aging leads to coarsening of the bulk microstructure and increased interfacial intermetallic compounds at the solder-pad interface. The coarsening of the solder bulk degrades the creep properties of solders, whereas the voiding and brittleness of interfacial intermetallic compounds leads to mechanical weakness of the solder joint. Industry guidelines on solder interconnect reliability test methods recommend preconditioning the solder assemblies by isothermal aging before conducting reliability tests. The guidelines assume that isothermal aging simulates a "reasonable use period," but do not relate the isothermal aging levels with specific use conditions. Studies on the effect of isothermal aging on the thermal cycling reliability of tin-lead and tin-silver-copper solders are limited in scope, and results have been contradictory. The effect of electrical current on solder joints has been has mostly focused on current densities above 104A/cm2 with high ambient temperature (≥100oC), where electromigration, thermomigration, and Joule heating are the dominant failure mechanisms. The effect of current density below 104A/cm2 on temperature cycling fatigue of solders has not been established. This research provides the relation between isothermal aging and the thermal cycling reliability of select Sn-based solders. The Sn-based solders with 3%, 1%, and 0% silver content that have replaced tin-lead are studied and compared against tin-lead solder. The activation energy and growth exponents of the Arrhenius model for the intermetallic growth in the solders are provided. An aging metric to quantify the aging of solder joints, in terms of phase size in the solder bulk and interfacial intermetallic compound thickness at the solder-pad interface, is established. Based on the findings of thermal cycling tests on aged solder assemblies, recommendations are made for isothermal aging of solders before thermal cycling tests. Additionally, the effect of active electrical current at 103 A/cm2 on thermal cycling reliability is reported

Numerical analysis of lead-free solder joints: effects of thermal cycling and electromigration

To meet the requirements of miniaturization and multifunction in microelectronics, understanding of their reliability and performance has become an important research subject in order to characterise electronics served under various loadings. Along with the demands of the increasing miniaturization of electronic devices, various properties and the relevant thermo-mechanical-electrical response of the lead-free solder joints to thermal cycling and electro-migration become the critical factors, which affect the service life of microelectronics in different applications. However, due to the size and structure of solder interconnects in microelectronics, traditional methods based on experiments are not applicable in the evaluation of their reliability under complex joint loadings. This thesis presents an investigation, which is based on finite-element method, into the performance of lead-free solder interconnects under thermal fatigue and electro-migration, specifically in the areas as follows: (1) the investigation of thermal-mechanical performance and fatigue-life prediction of flip-chip package under different sizes to achieve a further understanding of IMC layer and size effects of a flip chip package under thermal cycling; (2) the establishment of a numerical method, simulating void-formation/crack-propagation based on the results of finite-element analysis, to allow the prediction of crack evolution and failure time for electro-migration reliability of solder bumps; (3) the establishment of a flow-based algorithm for combination effects of thermal-mechanical and electro-migration that was subsequent implemented in to an FE model to evaluate the reliability assessment of service lives associated with a flip chip package

Modeling the SAC microstructure evolution under thermal, thermomechanical and electrical constraints

[no abstract

On the Interfacial Phase Growth and Vacancy Evolution during Accelerated Electromigration in Cu/Sn/Cu Microjoints

In this work, we integrate different computational tools based on multi-phase-field simulations to account for the evolution of morphologies and crystallographic defects of Cu/Sn/Cu sandwich interconnect structures that are widely used in three dimensional integrated circuits (3DICs). Specifically, this work accounts for diffusion-driven formation and disappearance of multiple intermetallic phases during accelerated electromigration and takes into account the non-equilibrium formation of vacancies due to electromigration. The work compares nucleation, growth, and coalescence of intermetallic layers during transient liquid phase bonding and virtual joint structure evolution subjected to accelerated electromigration conditions at different temperatures. The changes in the rate of dissolution of Cu from intermetallics and the differences in the evolution of intermetallic layers depending on whether they act as cathodes or anodes are accounted for and are compared favorably with experiments. The model considers non-equilibrium evolution of vacancies that form due to differences in couplings between diffusing atoms and electron flows. This work is significant as the point defect evolution in 3DIC solder joints during electromigration has deep implications to the formation and coalescence of voids that ultimately compromise the structural and functional integrity of the joints.NSF Grant No.CMMI-146225

Ultra thin ultrafine-pitch chip-package interconnections for embedded chip last approach

Ever growing demands for portability and functionality have always governed the electronic technology innovations. IC downscaling with Moore s law and system miniaturization with System-On-Package (SOP) paradigm has resulted and will continue to result in ultraminiaturized systems with unprecedented functionality at reduced cost. The trend towards 3D silicon system integration is expected to downscale IC I/O pad pitches from 40µm to 1- 5 µm in future. Device- to- system board interconnections are typically accomplished today with either wire bonding or solders. Both of these are incremental and run into either electrical or mechanical barriers as they are extended to higher density of interconnections. Alternate interconnection approaches such as compliant interconnects typically require lengthy connections and are therefore limited in terms of electrical properties, although expected to meet the mechanical requirements. As supply currents will increase upto 220 A by 2012, the current density will exceed the maximum allowable current density of solders. The intrinsic delay and electromigration in solders are other daunting issues that become critical at nanometer size technology nodes. In addition, formation of intermetallics is also a bottleneck that poses significant mechanical issues. Recently, many research groups have investigated various techniques for copper-copper direct bonding. Typically, bonding is carried out at 400oC for 30 min followed by annealing for 30 min. High thermal budget in such process makes it less attractive for integrated systems because of the associated process incompatibilities. In the present study, copper-copper bonding at ultra fine-pitch using advanced nano-conductive and non-conductive adhesives is evaluated. The proposed copper-copper based interconnects using advanced conductive and non-conductive adhesives will be a new fundamental and comprehensive paradigm to solve all the four barriers: 1) I/O pitch 2) Electrical performance 3) Reliability and 4) Cost. This thesis investigates the mechanical integrity and reliability of copper-copper bonding using advanced adhesives through test vehicle fabrication and reliability testing. Test vehicles were fabricated using low cost electro-deposition techniques and assembled onto glass carrier. Experimental results show that proposed copper-copper bonding using advanced adhesives could potentially meet all the system performance requirements for the emerging micro/nano-systems.M.S.Committee Chair: Prof. Rao R Tummala; Committee Member: Dr. Jack Moon; Committee Member: Dr. P M Ra

Thermo-migration behavior of SAC305 lead-free solder reinforced with fullerene nanoparticles

In this work, SAC305 lead-free solder reinforced with 0.1 wt. % fullerene nanoparticles was prepared using a powder metallurgy method. A lab-made setup and a corresponding Cu/solder/Cu sample for thermo-migration (TM) test were designed and implemented. The feasibility of this setup for TM stressing was further verified with experimental and simulation methods; a temperature gradient in a solder seam was calculated as 1070 K/cm. Microstructural evolution and mechanical properties of both plain and composite solder alloys were then studied under the condition of TM stressing. It was shown that compared to unreinforced SAC305 solder, the process of diffusion of Cu atoms in the composite solder seam was remarkably suppressed. After the TM test for 600 h, Cu/solder interfaces in the composite solder seam were more stable and the inner structure remained more intact. Moreover, the addition of fullerene reinforcement can considerably affect a distribution of Cu6Sn5 formed as a result of dissolution of Cu atoms during the TM test. Hardness data across the solder seam were also found notably different because of the elemental redistribution caused by TM

Développement d’un procédé d’électrodéposition séquentielle pour fabrication des microbilles à haute densité

Aujourd’hui l’industrie des semiconducteurs aborde une époque requérant le couplage de l’innovation au niveau de l'assemblage avec la mise à l’échelle des dispositifs. Cette dernière n’est plus l’élément clé qui propulse l’évolution technologique à cause de l’énorme investissement requis vis-à-vis sa rentabilité qui devient de plus en plus limitée. Avec la réorientation de l’intérêt de la majorité des acteurs vers l’innovation au niveau des assemblages, cette thèse s’inscrit dans un contexte d’amélioration de la fiabilité des assemblages de larges puces renversées pour le calul haute performance à travers le développement des microbilles de brasures à faible coût et de métallurgie optimisée. Des microbilles de brasure à faible coût et hétérogènes sont proposées comme une approche simple qui présente des bénéfices métallurgiques et économiques. D’une part, l’électrodéposition séquentielle des couches de Sn et Ag pures au lieu d’alliage est réalisée à un faible coût d’acquisition et avec une simplicité de maintenance. D’une autre part, la même installation d’électrodéposition de Sn et Ag purs peut servir à la fabrication d’une multitude de brasures avec différentes teneurs en Ag. Malgré le besoin d’une standardisation des procédés de fabrication des microbilles, les motivations citées précédemment peuvent constituer un facteur d’attraction pour l’industrie afin de l’adopter comme alternative à l’électrodéposition conventionnelle des alliages. En plus de son faible coût, l’approche de fabrication des microbilles par électrodéposition séquentielle amène une flexibilité métallurgique avec l’utilisation d’une barrière qui limite la diffusion d’Ag. Cette dernière résulte en une microbille de brasure unique, qui peut à la fois i) avoir une structure hétérogène avec une faible teneur en Ag dont la ductilité élevée est maintenue à proximité des couches fragiles de la métallisation de la puce lors des étapes de l’assemblage; ii) avoir une forme en pilier dont des bénéfices sont similaires à ceux du pilier en Cu en évitant les effets néfastes de sa rigidité sur les couches du BEOL. Les différentes étapes de fabrication des microbilles de brasure ont été développées en se limitant à des procédés qui peuvent être intégrés facilement dans un environnement de production industrielle. La manipulation de la métallurgie des joints de brasure a été réalisée avec succès en démontrant une structure hétérogène unique de brasure dans un assemblage de puces renversées