Design of ALU and Cache Memory for an 8 bit ALU

The design of an ALU and a Cache memory for use in a high performance processor was examined in this thesis. Advanced architectures employing increased parallelism were analyzed to minimize the number of execution cycles needed for 8 bit integer arithmetic operations. In addition to the arithmetic unit, an optimized SRAM memory cell was designed to be used as cache memory and as fast Look Up Table. The ALU consists of stand alone units for bit parallel computation of basic integer arithmetic operations. Addition and subtraction were performed using Kogge Stone parallel prefix hardware operating at 330MHz. A high performance multiplier was built using Radix 4 Modified Booth Encoder (MBE) and a Wallace Tree summation array. The multiplier requires single clock cycle for 8 bit integer multiplication and operates at a maximum frequency of 100MHz. Multiplicative division hardware was built for executing both integer division and square root. The division hardware computes 8-bit division and square root in 4 clock cycles. Multiplier forms the basic building block of all these functional units, making high level of resource sharing feasible with this architecture. The optimal operating frequency for the arithmetic unit is 70MHz. A 6T CMOS SRAM cell measuring 90 µm2 was designed using minimum size transistors. The layout allows for horizontal overlap resulting in effective area of 76 µm2 for an 8x8 array. By substituting equivalent bit line capacitance of P4 L1 Cache, the memory was simulated to have a read time of 3.27ns. An optimized set of test vectors were identified to enable high fault coverage without the need for any additional test circuitry. Sixteen test cases were identified that would toggle all the nodes and provide all possible inputs to the sub units of the multiplier. A correlation based semi automatic method was investigated to facilitate test case identification for large multipliers. This method of testability eliminates performance and area overhead associated with conventional testability hardware. Bottom up design methodology was employed for the design. The performance and area metrics are presented along with estimated power consumption. A set of Monte Carlo analysis was carried out to ensure the dependability of the design under process variations as well as fluctuations in operating conditions. The arithmetic unit was found to require a total die area of 2mm2 (approx.) in 0.35 micron process

Formal Verification of an Iterative Low-Power x86 Floating-Point Multiplier with Redundant Feedback

We present the formal verification of a low-power x86 floating-point multiplier. The multiplier operates iteratively and feeds back intermediate results in redundant representation. It supports x87 and SSE instructions in various precisions and can block the issuing of new instructions. The design has been optimized for low-power operation and has not been constrained by the formal verification effort. Additional improvements for the implementation were identified through formal verification. The formal verification of the design also incorporates the implementation of clock-gating and control logic. The core of the verification effort was based on ACL2 theorem proving. Additionally, model checking has been used to verify some properties of the floating-point scheduler that are relevant for the correct operation of the unit.Comment: In Proceedings ACL2 2011, arXiv:1110.447

Composite Iterative Algorithm and Architecture for q-th Root Calculation

An algorithm for the q-th root extraction, being q any integer, is presented in this paper. The algorithm is based on an optimized implementation of X^{1/q} by a sequence of parallel and/or overlapped operations: (1) reciprocal, (2) digit-recurrence logarithm, (3) left-to-right carry-free multiplication and (4) on-line exponential. A detailed error analysis and two architectures are proposed, for low precision q and for higher precision q. The execution time and hardware requirements are estimated for single and double precision floating-point computations for several radices; this helps to determine which radices result in the most efficient implementations. The architectures proposed improve the features of other architectures for q-th root extraction.Dans cet article, nous présentons un algorithme matériel pour l'extraction de la racine q-ième d'un nombre X, où q est un entier naturel non nul. Cet algorithme est basé sur une implantation optimisée de la fonction X^{1/q} par une séquence d'opérations parallèles et/ou superposées: (1) réciproque, (2) logarithme chiffre par chiffre, (3) multiplication de gauche-à-droite sans propagation de retenue et (4) exponentielle en ligne. Une analyse détaillée des erreurs et deux architectures sont proposées, pour q de basse précision et pour q de précision plus haute. Le temps d'exécution et les composants matériels à utiliser sont estimés pour des calculs en virgule flottante simple et double précision et pour plusieurs bases. Cette étude aide à déterminer quelles bases mènent aux implantations les plus efficaces. Les architectures proposées améliorent les caractéristiques d'architectures précédentes destinées à l'extraction des racines

High-Speed Function Approximation using a Minimax Quadratic Interpolator

A table-based method for high-speed function approximation in single-precision floating-point format is presented in this paper. Our focus is the approximation of reciprocal, square root, square root reciprocal, exponentials, logarithms, trigonometric functions, powering (with a fixed exponent p), or special functions. The algorithm presented here combines table look-up, an enhanced minimax quadratic approximation, and an efficient evaluation of the second-degree polynomial (using a specialized squaring unit, redundant arithmetic, and multioperand addition). The execution times and area costs of an architecture implementing our method are estimated, showing the achievement of the fast execution times of linear approximation methods and the reduced area requirements of other second-degree interpolation algorithms. Moreover, the use of an enhanced minimax approximation which, through an iterative process, takes into account the effect of rounding the polynomial coefficients to a finite size allows for a further reduction in the size of the look-up tables to be used, making our method very suitable for the implementation of an elementary function generator in state-of-the-art DSPs or graphics processing units (GPUs)

Parametrizable Architecture for Function Recursive Evaluation

Paper submitted to the XVIII Conference on Design of Circuits and Integrated Systems (DCIS), Ciudad Real, España, 2003.This paper presents a function evaluation method developed under the scope of recursive expression of function convolution. This approach is based on a unique parametrizable formula capable of providing function points by successive iteration. When tackling design level, it also shows suitable for developing architectural schemes capable of dealing with different speed and precision issues. An architecture for reconfigurable FPGA based in serial distributed arithmetic implements the design for fast prototyping. The case of combined trigonometric functions involved in rotation is analyzed under this scope. Compared with others methods, our proposal offers a good balance between speed and precision

Study of Recursive Divide Architectures and Implementation for Division and Multiplication

Multipliers have been key and critical components for most application-specific and general-purpose computer architectures. However, these architectures have been transitioning towards multiple cores that can process large amounts of data through parallel approaches to computation. Unfortunately, traditional arithmetic functional units that worked well for single-core architectures have the side effect of incurring large amounts of area and power. Consequently, multi-core architecture need new ways of thinking about increased throughput to handle large amounts of data. This work discusses implementation of different divider algorithms and presents a recursive high radix divide unit that is modified to handle both multiplication and division targeted at multi-core architectures. Results are obtained with a 65nm technology and show a significant decrease in area and power while still maintaining a low total latency by utilizing high radix encoding within the functional unit.School of Electrical & Computer Engineerin

HIGH-SPEED CO-PROCESSORS BASED ON REDUNDANT NUMBER SYSTEMS

There is a growing demand for high-speed arithmetic co-processors for use in applications with computationally intensive tasks. For instance, Fast Fourier Transform (FFT) co-processors are used in real-time multimedia services and financial applications use decimal co-processors to perform large amounts of decimal computations. Using redundant number systems to eliminate word-wide carry propagation within interim operations is a well-known technique to increase the speed of arithmetic hardware units. Redundant number systems are mostly useful in applications where many consecutive arithmetic operations are performed prior to the final result, making it advantageous for arithmetic co-processors. This thesis discusses the implementation of two popular arithmetic co-processors based on redundant number systems: namely, the binary FFT co-processor and the decimal arithmetic co-processor. FFT co-processors consist of several consecutive multipliers and adders over complex numbers. FFT architectures are implemented based on fixed-point and floating-point arithmetic. The main advantage of floating-point over fixed-point arithmetic is the wide dynamic range it introduces. Moreover, it avoids numerical issues such as scaling and overflow/underflow concerns at the expense of higher cost. Furthermore, floating-point implementation allows for an FFT co-processor to collaborate with general purpose processors. This offloads computationally intensive tasks from the primary processor. The first part of this thesis, which is devoted to FFT co-processors, proposes a new FFT architecture that uses a new Binary-Signed Digit (BSD) carry-limited adder, a new floating-point BSD multiplier and a new floating-point BSD three-operand adder. Finally, a new unit labeled as Fused-Dot-Product-Add (FDPA) is designed to compute AB+CD+E over floating-point BSD operands. The second part of the thesis discusses decimal arithmetic operations implemented in hardware using redundant number systems. These operations are popularly used in decimal floating-point co-processors. A new signed-digit decimal adder is proposed along with a sequential decimal multiplier that uses redundant number systems to increase the operational frequency of the multiplier. New redundant decimal division and square-root units are also proposed. The architectures proposed in this thesis were all implemented using Hardware-Description-Language (Verilog) and synthesized using Synopsys Design Compiler. The evaluation results prove the speed improvement of the new arithmetic units over previous pertinent works. Consequently, the FFT and decimal co-processors designed in this thesis work with at least 10% higher speed than that of previous works. These architectures are meant to fulfill the demand for the high-speed co-processors required in various applications such as multimedia services and financial computations

Tamper-Resistant Arithmetic for Public-Key Cryptography

Cryptographic hardware has found many uses in many ubiquitous and pervasive security devices with a small form factor, e.g. SIM cards, smart cards, electronic security tokens, and soon even RFIDs. With applications in banking, telecommunication, healthcare, e-commerce and entertainment, these devices use cryptography to provide security services like authentication, identification and confidentiality to the user. However, the widespread adoption of these devices into the mass market, and the lack of a physical security perimeter have increased the risk of theft, reverse engineering, and cloning. Despite the use of strong cryptographic algorithms, these devices often succumb to powerful side-channel attacks. These attacks provide a motivated third party with access to the inner workings of the device and therefore the opportunity to circumvent the protection of the cryptographic envelope. Apart from passive side-channel analysis, which has been the subject of intense research for over a decade, active tampering attacks like fault analysis have recently gained increased attention from the academic and industrial research community. In this dissertation we address the question of how to protect cryptographic devices against this kind of attacks. More specifically, we focus our attention on public key algorithms like elliptic curve cryptography and their underlying arithmetic structure. In our research we address challenges such as the cost of implementation, the level of protection, and the error model in an adversarial situation. The approaches that we investigated all apply concepts from coding theory, in particular the theory of cyclic codes. This seems intuitive, since both public key cryptography and cyclic codes share finite field arithmetic as a common foundation. The major contributions of our research are (a) a generalization of cyclic codes that allow embedding of finite fields into redundant rings under a ring homomorphism, (b) a new family of non-linear arithmetic residue codes with very high error detection probability, (c) a set of new low-cost arithmetic primitives for optimal extension field arithmetic based on robust codes, and (d) design techniques for tamper resilient finite state machines

IEEE Compliant Double-Precision FPU and 64-bit ALU with Variable Latency Integer Divider

Together the arithmetic logic unit (ALU) and floating-point unit (FPU) perform all of the mathematical and logic operations of computer processors. Because they are used so prominently, they fall in the critical path of the central processing unit - often becoming the bottleneck, or limiting factor for performance. As such, the design of a high-speed ALU and FPU is vital to creating a processor capable of performing up to the demanding standards of today\u27s computer users. In this paper, both a 64-bit ALU and a 64-bit FPU are designed based on the reduced instruction set computer architecture. The ALU performs the four basic mathematical operations - addition, subtraction, multiplication and division - in both unsigned and two\u27s complement format, basic logic operations and shifting. The division algorithm is a novel approach, using a comparison multiples based SRT divider to create a variable latency integer divider. The floating-point unit performs the double-precision floating-point operations add, subtract, multiply and divide, in accordance with the IEEE 754 standard for number representation and rounding. The ALU and FPU were implemented in VHDL, simulated in ModelSim, and constrained and synthesized using Synopsys Design Compiler (2006.06). They were synthesized using TSMC 0.1 3nm CMOS technology. The timing, power and area synthesis results were recorded, and, where applicable, compared to those of the corresponding DesignWare components.The ALU synthesis reported an area of 122,215 gates, a power of 384 mW, and a delay of 2.89 ns - a frequency of 346 MHz. The FPU synthesis reported an area 84,440 gates, a delay of 2.82 ns and an operating frequency of 355 MHz. It has a maximum dynamic power of 153.9 mW