Time-slot based architecture for power beam-assisted relay techniques in CR-WSNs with transceiver hardware inadequacies

Over the past two decades, numerous research projects have concentrated on cognitive radio wireless sensor networks (CR-WSNs) and their benefits. To tackle the problem of energy and spectrum shortfall in CR-WSNs, this research proposes an underpinning decode-&-forward (DF) relaying technique. Using the suggested time-slot architecture (TSA), this technique harvests energy from a multi-antenna power beam (PB) and delivers source information to the target utilizing energy-constrained secondary source and relay nodes. The study considers three proposed relay selection schemes: enhanced hybrid partial relay selection (E-HPRS), conventional opportunistic relay selection (C-ORS), and leading opportunistic relay selection (L-ORS). We present evidence for the sustainability of the suggested methods by examining the outage probability (OP) and throughput (TPT) under multiple primary users (PUs). These systems leverage time switching (TS) receiver design to increase end-to-end performance while taking into account the maximum interference constraint and transceiver hardware inadequacies. In order to assess the efficacy of the proposed methods, we derive the exact and asymptotic closed-form equations for OP and TPT & develop an understanding to learn how they affect the overall performance all across the Rayleigh fading channel. The results show that OP of the L-ORS protocol is 16% better than C-ORS and 75% better than E-HPRS in terms of transmitting SNR. The OP of L-ORS is 30% better than C-ORS and 55% better than E-HPRS in terms of hardware inadequacies at the destination. The L-ORS technique outperforms C-ORS and E-HPRS in terms of TPT by 4% and 11%, respectively

Performance enhancement of wireless communication systems through QoS optimisation

Providing quality of service (QoS) in a communication network is essential but challenging, especially when the complexities of wireless and mobile networks are added. The issues of how to achieve the intended performances, such as reliability and efficiency, at the minimal resource cost for wireless communications and networking have not been fully addressed. In this dissertation, we have investigated different data transmission schemes in different wireless communication systems such as wireless sensor network, device-to-device communications and vehicular networks. We have focused on cooperative communications through relaying and proposed a method to maximise the QoS performance by finding optimum transmission schemes. Furthermore, the performance trade-offs that we have identified show that both cooperative and non-cooperative transmission schemes could have advantages as well as disadvantages in offering QoS. In the analytical approach, we have derived the closed-form expressions of the outage probability, throughput and energy efficiency for different transmission schemes in wireless and mobile networks, in addition to applying other QoS metrics such as packet delivery ratio, packet loss rate and average end-to-end delay. We have shown that multi-hop relaying through cooperative communications can outperform non-cooperative transmission schemes in many cases. Furthermore, we have also analysed the optimum required transmission power for different transmission ranges to obtain the maximum energy efficiency or maximum achievable data rate with the minimum outage probability and bit error rate in cellular network. The proposed analytical and modelling approaches are used in wireless sensor networks, device-to-device communications and vehicular networks. The results generated have suggested an adaptive transmission strategy where the system can decide when and how each of transmission schemes should be adopted to achieve the best performance in varied conditions. In addition, the system can also choose proper transmitting power levels under the changing transmission distance to increase and maintain the network reliability and system efficiency accordingly. Consequently, these functions will lead to the optimized QoS in a given network

Timing and Carrier Synchronization in Wireless Communication Systems: A Survey and Classification of Research in the Last 5 Years

Timing and carrier synchronization is a fundamental requirement for any wireless communication system to work properly. Timing synchronization is the process by which a receiver node determines the correct instants of time at which to sample the incoming signal. Carrier synchronization is the process by which a receiver adapts the frequency and phase of its local carrier oscillator with those of the received signal. In this paper, we survey the literature over the last 5 years (2010–2014) and present a comprehensive literature review and classification of the recent research progress in achieving timing and carrier synchronization in single-input single-output (SISO), multiple-input multiple-output (MIMO), cooperative relaying, and multiuser/multicell interference networks. Considering both single-carrier and multi-carrier communication systems, we survey and categorize the timing and carrier synchronization techniques proposed for the different communication systems focusing on the system model assumptions for synchronization, the synchronization challenges, and the state-of-the-art synchronization solutions and their limitations. Finally, we envision some future research directions

System design issues in dense urban millimeter wave cellular networks

Upcoming deployments of cellular networks will see an increasing use of millimeter wave (mmWave) frequencies, roughly between 20-100 GHz. The goal of this dissertation is to investigate some key design issues in dense urban mmWave cellular networks by developing mathematical models that are representative of these networks. In the first contribution, stochastic geometry (SG) is used to study the per user rate performance of multi-user MIMO (MU-MIMO) in downlink mmWave cellular network incorporating the impact of a spatially sparse blockage dependent multipath channel and hybrid precoding. Performance of MU-MIMO is then compared with single-user beamforming and spatial multiplexing in different network scenarios considering coverage, rate and power consumption tradeoffs to suggest when to use which MIMO scheme. The second contribution reconsiders a popular received signal power model used in system capacity analysis of MIMO wireless networks employing single user beamforming. A modification is suggested to the model by introducing a correction factor. An approximate analysis is done to justify incorporating such a factor and simulations are performed to validate it's importance. Although this contribution does not study a new system design issue for mmWave cellular, it highlights a shortcoming with using the popular received signal power model to study design issues in mmWave cellular networks. The third and fourth contributions investigate resource allocation in self-backhauled mmWave cellular networks. In order to enable affordable initial deployments of mmWave cellular, self-backhauling is envisioned as a cost-saving solution. The third contribution investigates how to divide resources between uplink and downlink for access and backhaul in self-backhauled networks with single hop wireless backhauling. The performance of dynamic time division duplexing (TDD) and integrated access-backhaul (IAB) is compared with static TDD and orthogonal access backhaul (OAB) strategies using a SG based model. The last contribution of this dissertation addresses the following key question for self-backhauled networks. What is the maximum extended coverage area that a single fiber site can support using multi-hop relaying, while still achieving a minimum target per user data rate? The problem of maximizing minimum per user rates is studied considering a series of deployments with a single fiber site and varying number of relays. Several design guidelines for multi-hop mmWave cellular networks are provided based on the analytical and empirical results.Electrical and Computer Engineerin