Temporal and spatial combining for 5G mmWave small cells

This chapter proposes the combination of temporal processing through Rake combining based on direct sequence-spread spectrum (DS-SS), and multiple antenna beamforming or antenna spatial diversity as a possible physical layer access technique for fifth generation (5G) small cell base stations (SBS) operating in the millimetre wave (mmWave) frequencies. Unlike earlier works in the literature aimed at previous generation wireless, the use of the beamforming is presented as operating in the radio frequency (RF) domain, rather than the baseband domain, to minimise power expenditure as a more suitable method for 5G small cells. Some potential limitations associated with massive multiple input-multiple output (MIMO) for small cells are discussed relating to the likely limitation on available antennas and resultant beamwidth. Rather than relying, solely, on expensive and potentially power hungry massive MIMO (which in the case of a SBS for indoor use will be limited by a physically small form factor) the use of a limited number of antennas, complimented with Rake combining, or antenna diversity is given consideration for short distance indoor communications for both the SBS) and user equipment (UE). The proposal’s aim is twofold: to solve eroded path loss due to the effective antenna aperture reduction and to satisfy sensitivity to blockages and multipath dispersion in indoor, small coverage area base stations. Two candidate architectures are proposed. With higher data rates, more rigorous analysis of circuit power and its effect on energy efficiency (EE) is provided. A detailed investigation is provided into the likely design and signal processing requirements. Finally, the proposed architectures are compared to current fourth generation long term evolution (LTE) MIMO technologies for their anticipated power consumption and EE

Analysis and optimization of pilot symbol-assisted Rake receivers for DS-CDMA systems

The effect of imperfect channel estimation (CE) on the performance of pilot-symbol-assisted modulation (PSAM) and MRC Rake reception over time- or frequency-selective fading channels with either a uniform power delay profile (UPDP) or a nonuniform power delay profile (NPDP) is investigated. For time-selective channels, a Wiener filter or linear minimum mean square error (LMMSE) filter for CE is considered, and a closed-form asymptotic expression for the mean square error (MSE) when the number of pilots used for CE approaches infinity is derived. In high signal-to-noise ratio (SNR), the MSE becomes independent of the channel Doppler spectrum. A characteristic function method is used to derive new closed-form expressions for the bit error rate (BER) of Rake receivers in UPDP and NPDP channels. The results are extended to two-dimensional (2-D) Rake receivers. The pilot-symbol spacing and pilot-to-data power ratio are optimized by minimizing the BER. For UPDP channels, elegant results are obtained in the asymptotic case. Furthermore, robust spacing design criteria are derived for the maximum Doppler frequency

An adaptive correlator receiver for combined suppression of co-channel interference and narrow-band jammers in a slowly fading channel

This work deals with the adaptive correlation of a direct sequence spread spectrum signal in the presence of narrow-band, multipath and multiple user interference. The Least Mean Square and Recursive Least Square algorithms are employed for the adaptive convergence of the correlator receiver to minimize the mean squared error. The performance of the adaptive correlator is compared with the matched filter correlator receiver and the conventional prediction filter for the suppression of narrow-band interference by calculating the bit error probability rate. The adaptive correlator is also compared with the RAKE receiver for multipath suppression and compared to the decorelating detector for the suppression of multiple user interference. It is shown that the adaptive correlator is capable of suppressing interference when the spread spectrum signal is corrupted by a combination of disturbances, such as narrow-band jammers and multipath or multiple users on the same channel

Performance Evaluation of Impulse Radio UWB Systems with Pulse-Based Polarity Randomization

In this paper, the performance of a binary phase shift keyed random time-hopping impulse radio system with pulse-based polarity randomization is analyzed. Transmission over frequency-selective channels is considered and the effects of inter-frame interference and multiple access interference on the performance of a generic Rake receiver are investigated for both synchronous and asynchronous systems. Closed form (approximate) expressions for the probability of error that are valid for various Rake combining schemes are derived. The asynchronous system is modelled as a chip-synchronous system with uniformly distributed timing jitter for the transmitted pulses of interfering users. This model allows the analytical technique developed for the synchronous case to be extended to the asynchronous case. An approximate closed-form expression for the probability of bit error, expressed in terms of the autocorrelation function of the transmitted pulse, is derived for the asynchronous case. Then, transmission over an additive white Gaussian noise channel is studied as a special case, and the effects of multiple-access interference is investigated for both synchronous and asynchronous systems. The analysis shows that the chip-synchronous assumption can result in over-estimating the error probability, and the degree of over-estimation mainly depends on the autocorrelation function of the ultra-wideband pulse and the signal-to-interference-plus-noise-ratio of the system. Simulations studies support the approximate analysis.Comment: To appear in the IEEE Transactions on Signal Processin

Impact of Finger Placement on the Correlation Properties of Rake Combined Signals

3G mobile devices and base stations employ rake receivers. An important issue in the design of such receivers is finger allocation. This paper explores the relationship between finger placement and the correlation properties of rake combined signals. The dependence of correlation coefficients on system parameters such as the multipath characteristics of the propagation channel, the number of users, the processing gain and the thermal noise power is also discussed. Several conclusions useful in the analysis and design of rake receivers are drawn. A low complexity finger placement algorithm is finally suggested. In the proposed receiver, finger allocation is based on the correlation properties of the desired signal component only. The receiver performs close to complex structures in the literature

Adaptive RAKE receiver structures for ultra wide-band systems

Ultra wide band (UWB) is an emerging technology that recently has gained regulatory approval. It is a suitable solution for high speed indoor wireless communications due to its promising ability to provide high data rate at low cost and low power consumption. Another benefit of UWB is its ability to resolve individual multi-path components. This feature motivates the use of RAKE multi-path combining techniques to provide diversity and to capture as much energy as possible from the received signal. Potential future and rule limitation of UWB, lead to two important characteristics of the technology: high bit rate and low emitting power. Based on the power emission limit of UWB, the only choice for implementation is the low level modulation technology. To obtain such a high bit rate using low level modulation techniques, significant inter-symbol interference (ISI) is unavoidable. Three N (N means the numbers of fingers) fingers RAKE receiver structures are proposed: the N-selective maximal ratio combiner (MRC), the N-selective MRC receiver with least-mean-square (LMS) adaptive equalizer and the N-selective MRC receiver with LMS adaptive combiner. These three receiver structures were all simulated for N=8, 16 and 32. Simulation results indicate that ISI is effectively suppressed. The 16-selective MRC RAKE receiver with LMS adaptive combiner demonstrates a good balance between performance, computation complexity and required length of the training sequence. Due to the simplicity of the algorithm and a reasonable sampling rate, this structure is feasible for practical VLSI implementations

An Efficient Finger Allocation Method for the Maximum Likelihood RAKE Receiver

In wideband wireless communication systems the RAKE receiver is commonly used to collect the resolvable multipath energy and counter the effects of fading through diversity. However, in channels with large delay and energy spread, its high complexity still remains a major issue. This motivates the study and application of computationally efficient finger placement algorithms that significantly reduce the receiver complexity with a reasonable performance loss. In this paper, a low–complexity maximum likelihood RAKE receiver, the Suboptimum – Maximum Power Minimum Correlation (S–MPMC) RAKE is proposed. The allocation of its first two fingers is based on the received signal correlation properties. Their positions determine also the placement of the rest of the fingers. Simulation results are provided to show the operation of the receiver and demonstrate its performance. Comparisons with relevant methods are performed to corroborate the merits of the proposal. The balance on the performance and the complexity of the technique makes it suitable for use in commercial wideband communication systems