Attitude and position control of flapping-wing micro aerial vehicles

Compared with the fixed-wing and rotor aircraft, the flapping-wing micro aerial vehicle is of great interest to many communities because of its high efficiency and flexible maneuverability. However, issues such as the small size of the vehicles, complex dynamics and complicated systems due to uncertainty, nonlinearity, and multi-coupled parameters cause several significant challenges in construction and control. In this thesis, based on Euler angle and unit quaternion representations, the backstepping technique is used to design attitude stabilization controllers and position tracking controllers for a good control performance of a flapping-wing micro aerial vehicle. The attitude control of a apping{wing micro aerial vehicle is achieved by controlling the aerodynamic forces and torques, which are highly nonlinear and time{varying. To control such a complex system, a dynamic model is derived by using the Newton{Euler method. Based on the mathematical model, the backstepping technique is applied with the Lyapunov stability theory for the controller design. Moreover, because a flapping-wing micro aerial vehicle has very exible wings and oscillatory flight characteristics, the adaptive fuzzy control law as well as H1 control strategy are also used to estimate the unknown parameters and attenuate the impact of external disturbances. What is more, due to the problem of the gimbal lock of Euler angles, the unit quaternion representation is used afterwards. As for position control, the forward movement is controlled by the thrust and lift force generated by the wings of flapping-wing micro aerial vehicles. To make the actual position and velocity follow the desired trajectory and velocity, the backstepping scheme is used based on a unit quaternion representation. In order to reduce the complexity of differentiation of the virtual control in the design process, a dynamic surface control method is then used by the idea of a low-pass filter. Matlab simulation results prove the mathematical feasibility and also illustrate that all the proposed controllers have a stable control performance

DEVELOPMENT OF COAXIAL ROTOR MICRO UNMANNED AERIAL VEHICLE

Micro Unmanned Helicopter with ability of takeoff, landing and hovering offeres excellent support tool for missions in indoor environment. In this paper, a review of preliminary studies towards the development of autonomous coaxial helicopter MAV is presented. The paper starts with the statement of coaxial helicoper MAV development. Then, it is continued by the introduction of development of dynamic model for a typical coaxial rotor platform. In the third issues, initial steps in development of sensory system and control system will be dealt with. In brief, an analytical mathematical model has successful derived. This model together with the developed sensor system will act important role towards the full development of the dynamics model as the system identification is carried out

PAC: A Novel Self-Adaptive Neuro-Fuzzy Controller for Micro Aerial Vehicles

There exists an increasing demand for a flexible and computationally efficient controller for micro aerial vehicles (MAVs) due to a high degree of environmental perturbations. In this work, an evolving neuro-fuzzy controller, namely Parsimonious Controller (PAC) is proposed. It features fewer network parameters than conventional approaches due to the absence of rule premise parameters. PAC is built upon a recently developed evolving neuro-fuzzy system known as parsimonious learning machine (PALM) and adopts new rule growing and pruning modules derived from the approximation of bias and variance. These rule adaptation methods have no reliance on user-defined thresholds, thereby increasing the PAC's autonomy for real-time deployment. PAC adapts the consequent parameters with the sliding mode control (SMC) theory in the single-pass fashion. The boundedness and convergence of the closed-loop control system's tracking error and the controller's consequent parameters are confirmed by utilizing the LaSalle-Yoshizawa theorem. Lastly, the controller's efficacy is evaluated by observing various trajectory tracking performance from a bio-inspired flapping-wing micro aerial vehicle (BI-FWMAV) and a rotary wing micro aerial vehicle called hexacopter. Furthermore, it is compared to three distinctive controllers. Our PAC outperforms the linear PID controller and feed-forward neural network (FFNN) based nonlinear adaptive controller. Compared to its predecessor, G-controller, the tracking accuracy is comparable, but the PAC incurs significantly fewer parameters to attain similar or better performance than the G-controller.Comment: This paper has been accepted for publication in Information Science Journal 201

Attitude and Position Control of a Flapping Micro Aerial Vehicle

International audienc

Dynamics of Flapping Micro-Aerial Vehicles

[[abstract]]A dynamic-link rule base (DLRB) is introduced to the fuzzy inference systems for the purpose of speeding up and simplifying the fuzzy reasoning. This paper proposes a new reasoning mechanism by adding a dynamic-link rule base between the original rule base and the inference engine. The fuzzy inference system with a dynamic-link rule base is called a dynamic-link-rule-base-fuzzy-inference-system (DLRB-FIS). In the DLRB-FIS, only the fired rules, whose firing strengths are not equal to zero, are included for inference. The mathematical foundations, theorems and architecture of the DLRB-FIS are presented. A numeric example is also given for verifying the practicability of DLRB-FIS. The DLRB-FIS proposed has a general-purpose architecture. Therefore, it can be applied to many kinds of fields, such as fuzzy control, fuzzy image processing, fuzzy decision making, and fuzzy pattern recognition, etc[[conferencetype]]國際[[conferencedate]]20090610~20090612[[iscallforpapers]]Y[[conferencelocation]]St. Louis, US

꼬리날개 없는 날갯짓 초소형 비행체의 자세조절

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 기계항공공학부, 2020. 8. 김현진.최근 생체모방에 대한 관심이 커지면서 생명체의 구조, 외형, 움직임, 행동을 분석하여 그들의 장점을 로봇에 적용시켜 기존의 로봇이 해결할 수 없거나 특별한 임무를 좀 더 효과, 효율적으로 해결하려는 시도가 늘어나고 있다. 이러한 시도는 무인비행체 개발에도 적용되고 있으며 날갯짓 비행체가 이에 해당된다. 날개짓 비행체는 날개의 반복운동을 통해 발생하는 힘을 통해 비행하는 비행체로 일반적으로 꼬리날개의 유무에 따라 새를 모방한 비행체(미익형 비행체)와 곤충을 모방한 비행체(무미익형 비행체)로 구분할 수 있다. 무미익형 비행체의 경우 제자리 비행을 할 수 있고, 크기가 작고 무게가 가벼워 공기저항도 줄일 수 있으며, 날렵한 비행이 가능하다는 장점이 있지만, 수동 안정성을 확보하기 위한 제어면이 충분하지 않고 추력 생성과 동시에 3축으로의 제어 모멘트를 만들 수 있는 복잡한 매커니즘을 가지고 있다는 특징을 가지고 있다. 본 논문에서는 저자의 미익형 비행체의 연구개발 사례를 토대로 자율 비행을 할 수 있는 무미익형 비행체를 개발하기 위한 요소기술들과 초기 비행체 개발을 목표로 한다. 해당 목표를 달성하기 위해 저자는 시중에서 판매되고 있는 RC장난감을 활용해 30 gram 이하의 무게를 가지고 30cm3 이내의 크기를 가지는 무미익형 날갯짓 비행체를 개발을 진행하였다. 비행체 내부에는 구동기로 DC 모터와 서보모터가 존재하며, DC 모터는 날갯짓을 일으키는 기어 박스를 작동시켜 비행체의 무게를 지탱하기 위한 thrust를 생성하며 roll축 방향으로의 moment 생성에 관여하며, 서보모터는 날갯짓에서 발생하는 좌우 thrust의 방향을 조절하여 pitch 와 yaw 축으로의 모멘트를 생성하는데 사용된다. 비행체 내부에는 아두이노 보드 기반의 마이크로프로세서가 탑재되어 있어 비행체를 제어하기 위한 신호를 생성할 수 있으며 블루투스 통신 모듈을 가지고 있기 때문에 외부와 통신 역시 가능하다. 비행체의 자세를 제어하기 위해서는 구동기의 상호작용으로 인해 발생하는 힘의 물리량을 파악하는 것이 중요하다. 이를 위해 날갯짓 메커니즘에서 발생하는 힘을 측정하는 실험을 수행하였다. 측정실험을 통해 DC모터 입력 대비 thrust 크기, 서보모터 command 입력 대비 moment 크기 등의 관계를 파악하였다. 또한 날갯짓 비행체를 공중에 띄울 수 있는 충분한 크기의 thrust를 발생하는 것을 확인하였으며 자세 제어를 위한 모멘트 생성 역시 가능하다는 것을 확인하였다. 비행체의 자세를 제어하기 위해서는 3축 방향으로의 운동방정식을 유도하는 것이 필요하다. 이를 위해 roll, pitch, yaw 축 방향으로 비행체에서 발생하는 힘과 회전 운동과 관련한 운동방정식을 유도했으며 이를 통해 비행체의 자세를 안정화시킬 수 있도록 하는 PID 제어기 형태의 제어기를 설계하였다. 뿐만 아니라, 비행체의 궤적추종 제어를 위해 내부의 자세 제어기에 비행체의 위치를 토대로 계산되는 추가적인 외부 제어기를 설계하여 이중루프 제어기 형태를 적용시켜 시뮬레이션을 통해 비행체의 자세 제어와 궤적 추종 제어가 이루어짐을 확인하였다. 개발한 비행체와 앞서 설계한 제어기가 사용자의 의도에 맞는 성능을 내는지 확인하기 위해 자이로 실험장치를 제작하여 자세 제어 실험을 수행하였다. 해당 실험장치는 roll, pitch, yaw 축으로 회전이 가능하도록 제작하였으며 실험장치 자체의 무게를 줄이기 위해 MDF 소재를 사용하여 구조물를 만들었다. roll, pitch, yaw 3축이 각각 독립적으로 제어하는 것과 3축을 동시에 제어하는 2가지 상황을 고려하였으며 앞서 설계한 제어기가 해당 실험 장치 내부에서 사용자의 의도에 맞게 제어 성능을 보이는지 확인할 수 있었다. 궤적 추종제어를 위해서는 2가지 비행 상황을 설정하였다. 첫 번째 경우, 천장과 비행체 상단부에 실을 연결하여 2D 평면상에서 비행체가 주워진 궤적에 따라 움직이는지, 두 번째 경우, 비행체 상단부에 헬륨이 주입된 풍선을 연결시켜 3D 공간상에서 주워진 궤적을 따라 추종 비행하는지를 확인할 수 있는 상황이다. 두 가지 상황에서 모두 다양한 형태의 궤적을 비행체가 잘 추종하는지를 확인할 수 있었다. 끝으로, 외부 장치(실, 풍선)를 제거하여 공중에서 비행체가 제자리 비행을 할 수 있는지를 검증하는 실험을 진행하였으며, 15초가량 1m3 공간 내에서 제자리 비행이 이루어지는 것을 확인하였다.Flapping wing micro air vehicles (FWMAVs) that generate thrust and lift by flapping their wings are regarded as promising flight vehicles because of their advantages in terms of similar appearance and maneuverability to natural creatures. Reducing weight and air resistance, insect-inspired tailless FWMAVs are an attractive aerial vehicle rather than bird-inspired FWMAVs. However, they are challenging platforms to achieve autonomous flight because they have insufficient control surfaces to secure passive stability and a complicated wing mechanism for generating three-axis control moments simultaneously. In this thesis, as preliminary autonomous flight research, I present the study of an attitude regulation and trajectory tracking control of a tailless FWMAV developed. For these tasks, I develop my platform, which includes two DC motors for generating thrust to support its weight and servo motors for generating three-axis control moments to regulate its flight attitude. First, I conduct the force and moment measurement experiment to confirm the magnitude and direction of the lift and moment generated from the wing mechanism. From the measurement test, it is confirmed that the wing mechanism generates enough thrust to float the vehicle and control moments for attitude regulation. Through the dynamic equations in the three-axis direction of the vehicle, a controller for maintaining a stable attitude of the vehicle can be designed. To this end, a dynamic equation related to the rotational motion in the roll, pitch, and yaw axes is derived. Based on the derived dynamic equations, we design a proportional-integral-differential controller (PID) type controller to compensate for the attitude of the vehicle. Besides, we use a multi-loop control structure (inner-loop: attitude control, outer-loop: position control) to track various trajectories. Simulation results show that the designed controller is effective in regulating the platforms attitude and tracking a trajectory. To check whether the developed vehicle and the designed controller are operating effectively to regulate its attitude, I design a lightweight gyroscope apparatus using medium-density-fiberboard (MDF) material. The rig is capable of freely rotating in the roll, pitch, and yaw axes. I consider two situations in which each axis is controlled independently, and all axes are controlled simultaneously. In both cases, attitude regulation is properly performed. Two flight situations are considered for the trajectory tracking experiment. In the first case, a string connects between the ceiling and the top of the platform. In the second case, the helium-filled balloon is connected to the top of the vehicle. In both cases, the platform tracks various types of trajectories well in error by less than 10 cm. Finally, an experiment is conducted to check whether the tailless FWMAV could fly autonomously in place by removing external devices (string, balloon), and the tailless FWMAV flies within 1 m^3 space for about 15 seconds1.Introduction 1 1.1 Background & Motivation 1 1.2 Literature review 3 1.3 Thesis contribution 7 1.4 Thesis outline 8 2.Design of tailless FWMAV 13 2.1 Platform appearance 13 2.2 Flight control system 17 2.3 Principle of actuator mechanism 18 3.Force measurement experiment 28 3.1 Measurement setup 28 3.2 Measurement results 30 4.Dynamics & Controller design 37 4.1 Preliminary 37 4.2 Dynamics & Attitude control 39 4.2.1 Roll direction 41 4.2.2 Pitch direction 43 4.2.3 Yaw direction 45 4.2.4 PID control 47 4.3 Trajectory tracking control 48 5.Attitude regulation experiments 50 5.1 Design of gyroscope testbed 50 5.2 Experimental environment 52 5.3 Roll axis free 53 5.3.1 Simulation 54 5.3.2 Experiment 55 5.4 Pitch axis free 56 5.4.1 Simulation 57 5.4.2 Experiment 58 5.5 Yaw axis free 59 5.5.1 Simulation 59 5.5.2 Experiment 60 5.6 All axes free 60 5.6.1 Simulation 60 5.6.2 Experiment 61 5.7 Design of universal joint testbed & Experiment 64 6.Trajectory tracking 68 6.1 Simulation 68 6.2 Preliminary 69 6.3 Experiment: Tied-to-the-ceiling 70 6.4 Experiment: Hung-to-a-balloon 71 6.5 Summary 72 6.6 Hovering flight 73 7.Conclusion 83 A Appendix: Wing gearbox 85 A.1 4-bar linkage structure 85 B Appendix: Disturbance observer (DOB) 87 B.1 DOB controller 87 B.2 Simulation 89 B.2.1 Step input 89 B.2.2 Sinusoid input 91 B.3 Experiment 92 References 95Docto