Equalization of Third-Order Intermodulation Products in Wideband Direct Conversion Receivers

This paper reports a SAW-less direct-conversion receiver which utilizes a mixed-signal feedforward path to regenerate and adaptively cancel IM3 products, thus accomplishing system-level linearization. The receiver system performance is dominated by a custom integrated RF front end implemented in 130-nm CMOS and achieves an uncorrected out-of-band IIP3 of -7.1 dBm under the worst-case UMTS FDD Region 1 blocking specifications. Under IM3 equalization, the receiver achieves an effective IIP3 of +5.3 dBm and meets the UMTS BER sensitivity requirement with 3.7 dB of margin

Reducing dynamic power consumption in next generation DS-CDMA mobile communication receivers

Reduction of the power consumption in portable wireless receivers is important for cellular systems, including UMTS and IMT2000. This paper explores the architectural design-space and methodologies for reducing the dynamic power dissipation in the Direct Sequence Code Division Multiple Access (DS-CDMA) downlink RAKE receiver. At the algorithm level, we investigate the tradeoffs of reduced precision and arithmetic complexity on the receiver performance. We then present and analyse two architectures for implementing the reference and reduced complexity receivers, with respect to dynamic power dissipation. The combined effect of reduced precision and complexity reduction leads to a 37.44% power savings.Nokia CorporationTexas Instruments Inc.National Science Foundatio

Analog/RF Circuit Design Techniques for Nanometerscale IC Technologies

CMOS evolution introduces several problems in analog design. Gate-leakage mismatch exceeds conventional matching tolerances requiring active cancellation techniques or alternative architectures. One strategy to deal with the use of lower supply voltages is to operate critical parts at higher supply voltages, by exploiting combinations of thin- and thick-oxide transistors. Alternatively, low voltage circuit techniques are successfully developed. In order to benefit from nanometer scale CMOS technology, more functionality is shifted to the digital domain, including parts of the RF circuits. At the same time, analog control for digital and digital control for analog emerges to deal with current and upcoming imperfections

Channel-Aware Energy Optimization of OFDM Receivers Using Dynamic Precision Scaling in FPGAs

International audienceTo reduce the energy consumption of Orthogonal Frequency-Division Multiplexing (OFDM) systems, a new variable word-length method is presented in this paper. A simulation based approach is used: the optimized fixed-point implementation of an OFDM receiver is found for different simulated channel conditions, depending on the Signal-to-Noise Ratio (SNR) and the channel type. During the execution, the receiver estimates the channel conditions and chooses the optimum word-length to decode the received information. A realistic energy consumption of the receiver is estimated with a library that contains the energy consumption of Field-Programmable Gate Array (FPGA) basic operators depending on the bit-width, obtained from experimental data. Up to 57% of the dynamic energy can be saved using this method

Continuous-time low-pass filters for integrated wideband radio receivers

This thesis concentrates on the design and implementation of analog baseband continuous-time low-pass filters for integrated wideband radio receivers. A total of five experimental analog baseband low-pass filter circuits were designed and implemented as a part of five single-chip radio receivers in this work. After the motivation for the research work presented in this thesis has been introduced, an overview of analog baseband filters in radio receivers is given first. In addition, a review of the three receiver architectures and the three wireless applications that are adopted in the experimental work of this thesis is presented. The relationship between the integrator non-idealities and integrator Q-factor, as well as the effect of the integrator Q-factor on the filter frequency response, are thoroughly studied on the basis of a literature review. The theoretical study that is provided is essential for the gm-C filter synthesis with non-ideal lossy integrators that is presented after the introduction of different techniques to realize integrator-based continuous-time low-pass filters. The filter design approach proposed for gm-C filters is original work and one of the main points in this thesis, in addition to the experimental IC implementations. Two evolution versions of fourth-order 10-MHz opamp-RC low-pass filters designed and implemented for two multicarrier WCDMA base-station receivers in a 0.25-µm SiGe BiCMOS technology are presented, along with the experimental results of both the low-pass filters and the corresponding radio receivers. The circuit techniques that were used in the three gm-C filter implementations of this work are described and a common-mode induced even-order distortion in a pseudo-differential filter is analyzed. Two evolution versions of fifth-order 240-MHz gm-C low-pass filters that were designed and implemented for two single-chip WiMedia UWB direct-conversion receivers in a standard 0.13-µm and 65-nm CMOS technology, respectively, are presented, along with the experimental results of both the low-pass filters and the second receiver version. The second UWB filter design was also embedded with an ADC into the baseband of a 60-GHz 65-nm CMOS radio receiver. In addition, a third-order 1-GHz gm-C low-pass filter was designed, rather as a test structure, for the same receiver. The experimental results of the receiver and the third gm-C filter implementation are presented

Energy-Aware Computing via Adaptive Precision under Performance Constraints in OFDM Wireless Receivers

International audienceTo cope with rapid variations of channel parameters , wireless receivers are designed with a significant performance margin to reach a given Bit Error Rate (BER), even for the worst-case channel conditions. Indeed, one of the steps during the design phase is the choice of the architecture bit-width, and the smallest wordlength that ensures the correct behaviour of the receiver is usually chosen. In this paper, an adaptive precision OFDM receiver is proposed. Significant energy savings come from varying at run time processing bit-width, based on estimation of channel conditions, without compromising the BER constraints. To validate the energy savings, the energy consumption of basic operators has been obtained from real measurements for different bit-widths on a FPGA and a processor using soft SIMD. Results show that up to 63% of the dynamic energy consumption can be saved using this adaptive technique

Comparison of Wideband Earpiece Integrations in Mobile Phone

Perinteisesti puhelinverkoissa välitettävä puhe on ollut kapeakaistaista, kaistan ollessa 300 - 3400 Hz. Voidaan kuitenkin olettaa, että laajakaistaiset puhepalvelut tulevat saamaan markkinoilla enemmän jalansijaa tulevina vuosina. Tässä lopputyössä esitellään puheenkoodauksen perusteet laajakaistaisen adaptiivisen moninopeuspuhekoodekin (AMR-WB) kanssa. Laajakaistainen puhekoodekki laajentaa puhekaistan 50-7000 Hz käyttäen 16 kHz näytetaajuutta. Käytännössä laajempi kaista tarkoittaa parannuksia puheen ymmärrettävyyteen ja tekee siitä luonnollisemman ja mukavamman kuuloista. Tämän lopputyön päätavoite on vertailla kahden eri laajakaistaisen matkapuhelinkuulokkeen integrointia. Kysymys kuuluu, kuinka paljon käyttäjä hyötyy isommasta kuulokkeesta matkapuhelimessa? Kuulokkeiden suorituskyvyn selvittämiseksi niille tehtiin objektiivisia mittauksia vapaakentässä. Mittauksia tehtiin myös puhelimelle pää- ja torsosimulaattorissa (HATS) johdottamalla kuuloke suoraan vahvistimelle, sekä lisäksi puhelun ollessa aktiivisena GSM ja WCDMA verkoissa. Objektiiviset mittaukset osoittivat kahden eri integroinnin väliset erot kuulokkeiden taajuusvasteessa ja särössä erityisesti matalilla taajuuksilla. Lopuksi tehtiin kuuntelukoe tarkoituksena selvittää erottaako loppukäyttäjä pienemmän ja isomman kuulokkeen välistä eroa käyttäen kapeakaistaisia ja laajakaistaisia puhelinääninäytteitä. Kuuntelukokeen tuloksien pohjalta voidaan sanoa, että käyttäjä erottaa kahden eri integroinnin erot ja miespuhuja hyötyy naispuhujaa enemmän isommasta kuulokkeesta laajakaistaisella puhekoodekilla.The speech in telecommunication networks has been traditionally narrowband ranging from 300 Hz to 3400 Hz. It can be expected that wideband speech call services will increase their foothold in the markets during the coming years. In this thesis speech coding basics with adaptive multirate wideband (AMR-WB) are introduced. The wideband codec widens the speech band to new range from 50 Hz to 7000 Hz using 16 kHz sampling frequency. In practice the wider band means improvements to speech intelligibility and makes it more natural and comfortable to listen to. The main focus of this thesis work is to compare two different wideband earpiece integrations. The question is how much the end-user will benefit from using a larger earpiece in a mobile phone? To find out speaker performance, objective measurements in free field were done for the earpiece modules. Measurements were performed also for the phone on head and torso simulator (HATS) by wiring the earpieces directly to a power amplifier and with over the air on GSM and WCDMA networks. The results of objective measurements showed differences between the earpiece integrations especially on low frequencies in frequency response and distortion. Finally the subjective listening test is done for comparison to see if the end-user notices the difference between smaller and larger earpiece integrations using narrowband and wideband speech samples. Based on these subjective test results it can be said that the user can differentiate between two different integrations and that a male speaker benefits more from a larger earpiece than a female speaker

Introduction to the special issue on the 36th European Solid-State Circuits Conference (ESSCIRC)

The 22 papers in this special issue were originally presented at the 2010 European Solid-State Circuits Conference (ESSCIRC). The conference was jointly organized with the European Solid-State Device Research Conference and held September 14-16 in Seville, Spain. Papers cover the traditional ESSCIRC topics of analog circuits, digital circuits, data converters, sensors and imagers, and communications and RF circuits. Energy harvesting and biomedical circuits were also within ESSCIRC 2010 topics and are represented in this issue