Microprocessor fault-tolerance via on-the-fly partial reconfiguration

This paper presents a novel approach to exploit FPGA dynamic partial reconfiguration to improve the fault tolerance of complex microprocessor-based systems, with no need to statically reserve area to host redundant components. The proposed method not only improves the survivability of the system by allowing the online replacement of defective key parts of the processor, but also provides performance graceful degradation by executing in software the tasks that were executed in hardware before a fault and the subsequent reconfiguration happened. The advantage of the proposed approach is that thanks to a hardware hypervisor, the CPU is totally unaware of the reconfiguration happening in real-time, and there's no dependency on the CPU to perform it. As proof of concept a design using this idea has been developed, using the LEON3 open-source processor, synthesized on a Virtex 4 FPG

Self-Partial and Dynamic Reconfiguration Implementation for AES using FPGA

This paper addresses efficient hardware/software implementation approaches for the AES (Advanced Encryption Standard) algorithm and describes the design and performance testing algorithm for embedded system. Also, with the spread of reconfigurable hardware such as FPGAs (Field Programmable Gate Array) embedded cryptographic hardware became cost-effective. Nevertheless, it is worthy to note that nowadays, even hardwired cryptographic algorithms are not so safe. From another side, the self-reconfiguring platform is reported that enables an FPGA to dynamically reconfigure itself under the control of an embedded microprocessor. Hardware acceleration significantly increases the performance of embedded systems built on programmable logic. Allowing a FPGA-based MicroBlaze processor to self-select the coprocessors uses can help reduce area requirements and increase a system's versatility. The architecture proposed in this paper is an optimal hardware implementation algorithm and takes dynamic partially reconfigurable of FPGA. This implementation is good solution to preserve confidentiality and accessibility to the information in the numeric communication

Using SRAM Based FPGAs for Power-Aware High Performance Wireless Sensor Networks

While for years traditional wireless sensor nodes have been based on ultra-low power microcontrollers with sufficient but limited computing power, the complexity and number of tasks of today’s applications are constantly increasing. Increasing the node duty cycle is not feasible in all cases, so in many cases more computing power is required. This extra computing power may be achieved by either more powerful microcontrollers, though more power consumption or, in general, any solution capable of accelerating task execution. At this point, the use of hardware based, and in particular FPGA solutions, might appear as a candidate technology, since though power use is higher compared with lower power devices, execution time is reduced, so energy could be reduced overall. In order to demonstrate this, an innovative WSN node architecture is proposed. This architecture is based on a high performance high capacity state-of-the-art FPGA, which combines the advantages of the intrinsic acceleration provided by the parallelism of hardware devices, the use of partial reconfiguration capabilities, as well as a careful power-aware management system, to show that energy savings for certain higher-end applications can be achieved. Finally, comprehensive tests have been done to validate the platform in terms of performance and power consumption, to proof that better energy efficiency compared to processor based solutions can be achieved, for instance, when encryption is imposed by the application requirements

Reducing Rad-Hard Memories for FPGA Configuration Storage on Space-bound Payloads

FPGA use in space-based applications is becoming more common. Radiation-hardened (rad-hard) memories are typically used to store configuration data for programming the FPGA and performing bitstream scrubbing to remove errors in the system that occur from single event upsets (SEUs). Since device densities for the latest FPGAs are growing at a faster rate than rad-hard memories, it is becoming more difficult to reliably store the FPGA configuration data without using a large number of memories. We present a method for cutting the use of rad-hard memories necessary to support the use of the latest FPGA technologies in space-based applications. This paper describes a solution to this memory problem which utilizes FPGA partial reconfiguration, with device self-scrubbing, and bitstream compression to create a minimally sized bootstrap design that has a memory footprint that is a fraction of the size of the original design. This bootstrap design is stored locally, and the remaining design elements can be reconfigured as necessary from a remote location. The resulting prototype design yields a compressed bitstream that at less than 2% the size of the bitstream for largest FPGA currently on the market

Hardware Fault Injection

Hardware fault injection is the widely accepted approach to evaluate the behavior of a circuit in the presence of faults. Thus, it plays a key role in the design of robust circuits. This chapter presents a comprehensive review of hardware fault injection techniques, including physical and logical approaches. The implementation of effective fault injection systems is also analyzed. Particular emphasis is made on the recently developed emulation-based techniques, which can provide large flexibility along with unprecedented levels of performance. These capabilities provide a way to tackle reliability evaluation of complex circuits.Publicad

Using Relocatable Bitstreams for Fault Tolerance

This research develops a method for relocating reconfigurable modules on the Virtex-II (Pro) family of Field Programmable Gate Arrays (FPGAs). A bitstream translation program is developed which correctly changes the location of a partial bitstream that implements a module on the FPGA. To take advantage of relocatable modules, three fault-tolerance circuit designs are developed and tested. This circuit can operate through a fault by efficiently removing the faulty module and replacing it with a relocated module without faults. The FPGA can recover from faults at a known location, without the need for external intervention using an embedded fault recovery system. The recovery system uses an internal PowerPC to relocate the modules and reprogram the FPGA. Due to the limited architecture of the target FPGA and Xilinx tool errors, an FPGA with automatic fault recovery could not be demonstrated. However, the various components needed to do this type of recovery have been implemented and demonstrated individually

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria

Development of a Reconfigurable Multi-Faceted Communications Device Using Partial Dynamic Reconfiguration

Supporting a variety of communication protocols has typically required extensive hard- ware and Input/Output (I/O) interfaces targeting each protocol specifically. Recent designs in the past ten years have created more dynamic approaches by using Field Programmable Gate Arrays (FPGAs) and embedded hardware to implement or simulate previous hardware I/O designs. With the constant increase in FPGA and embedded technologies the capabilities of dynamic implementations have expanded. This report addresses the design of an up-to-date reconfigurable multi-faceted embedded device targeting recent technological advances in FPGAs

Microprocessor and FPGA interfaces for in-system co-debugging in field programmable hybrid systems

Modern trends in technology require efficient control and processing platforms based on connected software-hardware subsystems. Due to their complexity and size, algorithms implemented on these platforms are difficult to test and verify. When these types of solution are being designed, it is necessary to provide information of the internal values of registers and memories of both the software and hardware during the execution of the complete system. The final architecture of the targeted design and its debugging capabilities strongly depends on how the hybrid system is connected and clocked. This article discusses different architectural strategies that have been adopted for a hybrid hardware-software platform, built ready for debugging, and that uses components that can be easily found with a few special features. All the solutions have been implemented and evaluated using the UNSHADES-2 framework