Compact near field wireless energy transfer systems using defected ground structures

Near-Field Wireless Power Transfer systems have attracted attention for their potential applications, such as implanted medical devices, radio frequency identification, and portable electronic devices in general. In this context, a compact model for short-range NF-WPT systems operating in ISM frequency bands is proposed, employing the concept of ground plane aperture resonators or Defected Ground Structures (DGS). This technique allows the miniaturization of the resonator, which leads to the development of compact NF-WPT systems. The model proposed in this work aims at possible applications that require simultaneous energy and data transfer. This model operates in dual band in 433 MHz and 900 MHz frequency bands and makes use of overlapping circular DGS in order to shrink the resonator device and obtain high values of Figure of Merit (FoM) commonly used in this research area. The proposed model was designed using the electromagnetic analysis and built using Rogers RO4003 dielectric material. The designed dual-band DGS resonators have a total area of 11.7 × 10.2 mm 2 and when placed at a distance of 15 mm between transmitter and receiver, they have measured FoM values of 0.71 and 1.07 at 440 MHz and 918 MHz, respectively. The results were compared with related works found in the literature, and indicate a ηWPT of 40.9% and 49.2 %

Dual-Band Resonator Designs for Near-Field Wireless Energy Transfer Applications

Dual-band near-field wireless energy transfer (WET) designs outweigh single-band system with regard to either concurrent energy and data transfer or multiple wireless charging standard functionalities. There are two major approaches in resonator designs, namely, multi-coil and single-coil. This chapter presents a review on design constraints for each design approach and rectification techniques available in counteracting impediments of dual-band near-field WET systems. Challenges pertinent to link design are discussed primarily followed by methods implemented to mitigate detrimental impact on performance metrics. Front-end dual-band resonator design methods are accentuated in this chapter in lieu of end-to-end WET system. This is envisioned to offer insights for designers contemplating on design modes or developing ways to facilitate a boost in rectification options currently available

Recent Advancements in Defected Ground Structure Based Near-Field Wireless Power Transfer Systems

The defected ground structure (DGS) technique enables miniaturization of the resonator which leads to the development of the compact near-field wireless power transfer (WPT) systems. In general, numerous challenges are inherent in the design of the DGS-based WPT systems and, hence, appropriate trade-offs for achieving optimal performance are required. Furthermore, the design advancements have led to the development of the DGS-based multi-band WPT systems to fulfill the needs of simultaneous data and power transfer. The innovations in the DGS-based WPT systems have also resulted in the definition of more commonly used figures-of-merit for the benchmarking of various performance metrics. The literature is replete with the design schemes to address one or more associated design challenges and successful WPT system realizations with enhanced performance. With this in mind, this paper touches upon the DGS-based WPTs developments and presents a concise report on the current state-of-the-art and future directions.Comment: 12 pages, 11 figures, to be published in IEEE Acces

Miniaturised and reconfigurable planar filters for ultra-wideband applications

An increasing demand for electromagnetic spectrum has resulted from the emergence of feature-rich and faster throughputs wireless applications. This necessitates the developments of dynamic reconfigurable or multifunctional systems to better exploit the existing spectrum. Future wireless devices will be expected to communicate over several bands with various other devices in order to fine tune the services they provide to the user. Each band may require a separate RF transceiver and such modern wireless multi-band multi-mode communication systems call for high performance, highly integrated compact modules. Since the Federal Communications Commission (FCC) released the unlicensed frequency band 3.1-10.6 GHz for ultra-wideband (UWB) commercial communications, the development race for commercialising UWB technology has seen a dramatic increase around the world. The aim of this research is to develop reconfigurable planar microwave filters for ultrawideband applications. The project investigates some key design issues of reconfigurable filters, which are being observed constantly in the latest development and realisation of microwave filters. Both analytical and numerical methods are performed to construct a realistic and functional design. Two different types of frequency reconfigurability are investigated in this thesis: discrete (e.g. PIN diode, Optical switch) and continuous (e.g. varactor diode). Using the equivalent circuits and considering the direct coupled filter structure in most cases, several topologies with attractive features are developed for future communication systems. The proposed works may be broadly categorised into three sections as follows. The first section explores a square ring shape close loop resonator along with an opencircuited stub in the symmetry plane. To realise a reconfigurable frequency states within the same spectrum, an innovative approach is developed for this case. An optical or photoconductive switch, comprised of a silicon die activated using near infrared light is investigated as a substitute of PIN diode and performances are evaluated to compare the feasibilities. In addition, a in-band interference rejection technique via externally coupled Tshape resonator is shown. However, it is observed that both structures achieve significant size reductions by utilising the inner part of the resonators. To improve the filter selectivity, a convenient design approach generating a pair of transmission zeros between both passband edges and a single zero in the stop band for harmonic suppression is discussed in the second section. Moreover, the development of notched rejection bands are studied and several novel methods to create a single and multiple notched bands employing the square ring shape structure are proposed. On inspection, it is found that the notch structure can be implemented without deteriorating the filter performances. The discussions are supplemented with detailed design examples which are accompanied by theoretical, simulated and experimental results in order to illustrate the filter development process and showcase practical filter performance. The third section reveals a novel highly compact planar dual-mode resonator with sharp rejections characteristics for UWB applications. A bandwidth reconfiguring technique is demonstrated by splitting its even-mode resonance. Filter structure with the dual-mode resonator is shown to have a relatively wide tuning range, significantly low insertion loss and a constant selectivity along with frequency variations in comparison to similar published works. Finally, the earlier dual-mode structure are modified to realise a dual wideband behaviour. A detail analysis with comprehensive design procedures is outlined and a solution for controlling the frequency bandwidths independently according to the application interest is provided. In line with the previous section, experimental verification is presented to support and supplement the discussions

Co-design of Reconfigurable and Multifunction Passive RF/Microwave Components

In order to meet the market demands, multi-band communication systems that are able to accommodate different wireless technologies to be compatible with different wireless standards should be investigated and realized. Multifunction and multi-band RF front-end components are promising solutions for reducing the size and enhancing the performance of multi-band communication systems. This dissertation focuses on the design and implementation of different multifunction and tunable microwave components for use in multi-standard, flexible transceiver. For frequency-domain duplexing (FDD) communication systems, in which the uplink and downlink channels are carried on different RF frequencies, a diplexer is an essential component to separate the transmitting and receiving signals from the antenna. Electrically tunable diplexers simplify the architecture of reconfigurable RF-front end. Moreover, in modern communication systems, the crowding of the spectrum and the scaling of electronics can result in higher common-mode interference and even-order non-linearity issues. In this dissertation, three tunable compact SIW-based dual-mode diplexers, with various SE (single-ended) and BAL (balanced) capabilities, are introduced for the first time. The dual-mode operation results in a dependent tuning between the two ports. The presented designs are for SE-SE, SE-BAL, and BAL-BAL. However, based on the presented design concepts, any combination of the diplexer ports can be achieved in terms of supporting the balanced and single-ended system interface. The fabricated diplexers show low insertion loss, high isolation, good tuning range and high common mode rejection. Tunable bandstop filter (BSF) is one of the essential components in the design of RF front-ends that require wide-band operations. A wide-open front-end leaves the receiver vulnerable to jamming by high-power signals. As a result, this type of front-ends requires dynamic isolation of any interfering signal. Realization of such filters in a balanced configuration, as a second function, is an important step in the realization of full-balanced RF front-ends. Balanced (differential) circuits have many important advantages over unbalanced (single-ended) circuits such as immunity to system noise, reduction of transient noise generation and inherent suppression of even-order nonlinearities. All reported balanced filters are bandpass filters that target wide pass-bands and high common-mode rejection. These filters are necessary for wide-band RF front-ends but, as mentioned above, leave the system open to interferers and jammers. In this dissertation, a new differential coupling structure for evanescent-mode cavity resonators is developed, enabling the design of fully-balanced tunable BSF. The proposed filter is tunable from 1.57-3.18 GHz with 102% tuning range. In addition, over the full range, the measured 10-dB fractional bandwidth ranges from 1-2.4%, and the attenuation level is better than 47 dB. Lastly, Substrate Integrated Waveguide (SIW) evanescent-mode cavity resonators (EVA) are employed in the design of RF couplers, quadrature hybrid and rat-race couplers. These couplers are used in the design of numerous RF front-end components such as power amplifiers, balanced mixers, and antenna array feeding networks. Utilizing such resonators (EVA) in the design allows the couplers to have wide spurious-free range, low power consumption, high power handling capability and both tunability and filtering capabilities. The proposed quadrature hybrid coupler can be tuned starting from 1.32–2.22 GHz with a measured insertion loss range from 1.29 to 0.7 dB. The measured reflection and isolation are better than 12 dB and 17 dB, respectively. Moreover, the coupler has a measured spurious free range of 5.1–3fo (lowest–highest frequency). Regarding rat-race coupler, two designs are introduced. The first design is based on a full-mode cavity while the second one is more compact and based on a half-mode cavity. Both designs show more than 70% tuning range, and the isolation is better than 30 dB

Compensation technique for nonlinear distortion in RF circuits for multi-standard wireless systems

Recent technological advances in the RF and wireless industry has led to the design requirement of more sophisticated devices which can meet stringent specifications of bandwidth, data rate and throughput. These devices are required to be extremely sensitive and hence any external interference from other systems can severely affect the device and the output. This thesis introduces the existing problem in nonlinear components in a multi-standard wireless system due to interfering signals and suggests potential solution to the problem. Advances in RF and wireless systems with emerging new communication standards have made reconfigurablility and tunability a very viable option. RF transceivers are optimised for multi-standard operation, where one band of frequency can act as an interfering signal to the other band. Due to the presence of nonlinear circuits in the transceiver chains such as power amplifiers, reconfigurable and tunable filters and modulators, these interfering signals produce nonlinear distortion products which can deform the output signal considerably. Hence it becomes necessary to block these interfering signals using special components. The main objective of this thesis is to analyse and experimentally verify the nonlinear distortions in various RF circuits such as reconfigurable and tunable filters and devise ways to minimize the overall nonlinear distortion in the presence of other interfering signals. Reconfigurbality and tunablity in filters can be achieved using components such as varactor diodes, PIN diodes and optical switches. Nonlinear distortions in such components are measured using different signals and results noted. The compensation method developed to minimize nonlinear distortions in RF circuits caused due to interfering signals is explored thoroughly in this thesis. Compensation method used involves the design of novel microstrip bandstop filters which can block the interfering signals and hence give a clean output spectrum at the final stage. Recent years have seen the emergence of electronic band gap technology which has “band gap” properties meaning that a bandstop response is seen within particular range of frequency. This concept was utilised in the design of several novel bandstop filters using defected microstrip structure. Novel tunable bandstop filters has been introduced in order to block the unwanted signal. Fixed single-band and dual-band filters using DMS were fabricated with excellent achieved results. These filters were further extended to tunable structures. A dual-band tunable filter with miniaturized size was developed and designed. The designed filters were further used in the compensation technique where different scenarios showing the effect of interfering signals in wireless transceiver were described. Mathematical analysis proved the validation of the use of a bandstop filter as an inter-stage component. Distortion improvements of around 10dB have been experimentally verified using a power amplifier as device under test. Further experimental verification was carried out with a transmitter which included reconfigurable RF filters and power amplifier where an improvement of 15dB was achieved

UWB Technology

Ultra Wide Band (UWB) technology has attracted increasing interest and there is a growing demand for UWB for several applications and scenarios. The unlicensed use of the UWB spectrum has been regulated by the Federal Communications Commission (FCC) since the early 2000s. The main concern in designing UWB circuits is to consider the assigned bandwidth and the low power permitted for transmission. This makes UWB circuit design a challenging mission in today's community. Various circuit designs and system implementations are published in this book to give the reader a glimpse of the state-of-the-art examples in this field. The book starts at the circuit level design of major UWB elements such as filters, antennas, and amplifiers; and ends with the complete system implementation using such modules

WPT, Recent Techniques for Improving System Efficiency

Wireless power transfer (WPT) technologies have received much more attention during the last decade due to their effectiveness in wireless charging for a wide range of electronic devices. To transmit power between two points without a physical link, conventional WPT systems use two coils, one coil is a transmitter (Tx) and the other is a receiver (Rx) which generates an induced current from the received power. Two main factors control the performance of the WPT schemes, power transfer efficiency (PTE) and transmission range. Power transfer efficiency refers to how much power received by the rechargeable device compared to the power transmitted from the transmitter; while transmission range indicates the longest distance between transmitter and receiver at which the receiver can receive power within the acceptable range of power transfer efficiency. Several studies were carried out to improve these two parameters. Many techniques are used for WPT such as inductive coupling, magnetic resonance coupling, and strongly coupled systems. Recently, metamaterial structures are also proposed for further transfer efficiency enhancement. Metamaterials work as an electromagnetic lensing structure that focuses the evanescent transmitted power into receiver direction. Transmitting & Receiving antenna systems may be used for sending power in certain radiation direction. Optimizing the transmitter antenna and receiver antenna characteristics increase the efficiency for WPT systems. This chapter will present a survey on different wireless power transmission schemes

Design, Modelling and Implementation of Several Multi-Standard High Performance Single-Wideband and Multi-Wideband Microwave Planar Filters

The objectives of this work are to review, investigate and model the microwave planar filters of the modern wireless communication system. The recent main stream of microwave filters are classified and discussed separately. Various microwave filters with detailed applications are investigated in terms of their geometrical structures and operational performances. A comprehensive theoretical study of microwave filters is presented. The main types of microwave filters including the basic low-pass filters such as Butterworth and Chebyshev filters are fully analysed and described in detail. The transformation from low-pass prototype filters to high-pass filters, band-pass filters and band-stop filters are illustrated and introduced. Research work on stepped impedance resonator (SIR) and asymmetric stepped impedance resonator (ASIR) structure is presented. The characteristics of λg/4, λg/2 and λg (λg is the guided wavelength of the fundamental frequency in the free space) type SIR resonators, and the characteristic of asymmetric SIR resonator are categorized and investigated. Based on the content mentioned above, novel multi-standard high performance asymmetric stepped impedance resonator single-wideband and dual-wideband filters with wide stopbands are proposed. The methodologies to realize wide passband and wide stop-band filters are detailed. In addition, multi-standard high performance triplewideband, quadruple-wideband and quint-wideband filters are suggested and studied. The measurement results for all prototype filters agree well with the theoretical predictions and simulated results from Ansoft HFSS software. The featured broad bandwidths over single/multiple applicable frequency bands and the high performances of the proposed filters make them very promising for applications in future multistandard wireless communication

Design and analysis of miniaturized substrate integrated waveguide reconfigurable filters for mm-wave applications.

Doctoral Degree. University of KwaZulu-Natal, Durban.Microwave filters are an integral part of communication systems. With the advent of new technologies, microwave devices, such as filters, need to have superior performance in terms of power handling, selectivity, size, insertion loss etc. During the past decade, many applications have been added to the communication networks, resulting in communication systems having to operate at high frequencies in the region of THz to achieve the stringent bandwidth requirements. To achieve the requirements of the modern communication system, tunability and reconfigurability have become fundamental requirements to reduce the footprint of communication devices. However, the communication systems that are more prevalent such as planar circuits have either a large footprint or are not able to handle large amounts of power due to radiation leakage. In this thesis, Substrate Integrated Waveguide (SIW) technology has been employed. The SIW has the same properties as the conventional rectangular waveguide; hence it benefits from the high quality (Q) factor and can handle large powers with small radiation loss. The Half-mode (HMSIW), Quarter-mode (QMSIW), and Eighth-mode (EMSIW) cavity resonators have been designed and used for the miniaturization of the microwave filters. The coupling matrix method was used to implement a filter that uses cross-coupled EMSIW and HMSIW cavity resonators to improve the selectivity of the filter. Balanced circuit techniques have been used to design the circuits that preserve communication systems integrity whereby the Common Mode (CM) signal was suppressed using Deformed Ground Structure (DGS) and a center conductor patch with meandered line. For the designed dual-band filter, the common mode signal was suppressed to -90 dB and - 40 dB for the first and second passband, respectively. The insertion loss observed is 2.8 dB and 1.6 dB for the first and second passband, respectively. For tunability of the filter, a dual-band filter utilizing triangular HMSIW resonators has been designed and reconfigurability is achieved by perturbing the substrate permittivity by dielectric rods. The dielectric rods’ permittivity was changed to achieve tunability in the first instance, and then the rods’ diameter changed in the second instance. For the lowerband, frequency is tunable from 8.1 GHz to 9.15 GHz, while the upper band is tuned from 14.61 GHz to 16.10 GHz. A second order SIW filter with a two layer substrate was then designed to operate in the THz region. For reconfigurability, Graphene was sandwiched between the Silicon Di-Oxide substrate and the top gold plate of the filter, and the chemical potential of Graphene was then varied by applying a dc bias voltage. With a change in dc voltage the chemical potential of Graphene changes accordingly. From the results, a chemical potential change of 0.1 eV to 0.6 eV brings about a frequency change from 1.289 THz to 1.297 THz