FORCED STACK SLEEP TRANSISTOR (FORTRAN): A NEW LEAKAGE CURRENT REDUCTION APPROACH IN CMOS BASED CIRCUIT DESIGNING

Reduction in leakage current has become a significant concern in nanotechnology-based low-power, low-voltage, and high-performance VLSI applications. This research article discusses a new low-power circuit design the approach of FORTRAN (FORced stack sleep TRANsistor), which decreases the leakage power efficiency in the CMOS-based circuit outline in VLSI domain. FORTRAN approach reduces leakage current in both active as well as standby modes of operation. Furthermore, it is not time intensive when the circuit goes from active mode to standby mode and vice-versa. To validate the proposed design approach, experiments are conducted in the Tanner EDA tool of mentor graphics bundle on projected circuit designs for the full adder, a chain of 4-inverters, and 4-bit multiplier designs utilizing 180nm, 130nm, and 90nm TSMC technology node. The outcomes obtained show the result of a 95-98% vital reduction in leakage power as well as a 15-20% reduction in dynamic power with a minor increase in delay. The result outcomes are compared for accuracy with the notable design approaches that are accessible for both active and standby modes of operation

Energy Efficient Design for Deep Sub-micron CMOS VLSIs

Over the past decade, low power, energy efficient VLSI design has been the focal point of active research and development. The rapid technology scaling, the growing integration capacity, and the mounting active and leakage power dissipation are contributing to the growing complexity of modern VLSI design. Careful power planning on all design levels is required. This dissertation tackles the low-power, low-energy challenges in deep sub-micron technologies on the architecture and circuit levels. Voltage scaling is one of the most efficient ways for reducing power and energy. For ultra-low voltage operation, a new circuit technique which allows bulk CMOS circuits to work in the sub-0. 5V supply territory is presented. The threshold voltage of the slow PMOS transistor is controlled dynamically to get a lower threshold voltage during the active mode. Due to the reduced threshold voltage, switching speed becomes faster while active leakage current is increased. A technique to dynamically manage active leakage current is presented. Energy reduction resulting from using the proposed structure is demonstrated through simulations of different circuits with different levels of complexity. As technology scales, the mounting leakage current and degraded noise immunity impact performance especially that of high performance dynamic circuits. Dual threshold technology shows a good potential for leakage reduction while meeting performance goals. A model for optimally selecting threshold voltages and transistor sizes in wide fan-in dynamic circuits is presented. On the circuit level, a novel circuit level technique which handles the trade-off between noise immunity and energy dissipation for wide fan-in dynamic circuits is presented. Energy efficiency of the proposed wide fan-in dynamic circuit is further enhanced through efficient low voltage operation. Another direct consequence of technology scaling is the growing impact of interconnect parasitics and process variations on performance. Traditionally, worst case process, parasitics, and environmental conditions are considered. Designing for worst case guarantees a fail-safe operation but requires a large delay and voltage margins. This large margin can be recovered if the design can adapt to the actual silicon conditions. Dynamic voltage scaling is considered a key enabler in reducing such margin. An on-chip process identifier to recover the margin required due to process variations is described. The proposed architecture adjusts supply voltage using a hybrid between the one-time voltage setting and the continuous monitoring modes of operation. The interconnect impact on delay is minimized through a novel adaptive voltage scaling architecture. The proposed system recovers the large delay and voltage margins required by conventional systems by closely tracking the actual critical path at anytime. By tracking the actual critical path, the proposed system is robust and more energy efficient compared to both the conventional open-loop and closed-loop systems

Low-Power High-Speed Double Gate 1-bit Full Adder Cell

In this paper, we proposed an efficient full adder circuit using 16 transistors. The proposed high-speed adder circuit able to operate at very low voltage and maintain the proper output voltage swing and also balanced the power consumption and speed. Proposed design is based on CMOS mixed threshold voltage logic (MTVL) and implemented in 180nm CMOS technology). In the proposed technique the most time-consuming and power consuming XOR gates and multiplexor are designed using MTVL scheme. The maximum average power consumed by the proposed circuit is 6.94µW at 1.8V supply voltage and frequency of 500 MHz, which is less than other conventional methods. Power, delay, and area are optimized by using pass transistor logic and verified using SPICE simulation tool at desired broad frequency range. It is also observed that the proposed designs successfully utilized in many cases, especially whenever the lowest power consumption and delay are aimed

Low power predictable memory and processing architectures

Great demand in power optimized devices shows promising economic potential and draws lots of attention in industry and research area. Due to the continuously shrinking CMOS process, not only dynamic power but also static power has emerged as a big concern in power reduction. Other than power optimization, average-case power estimation is quite significant for power budget allocation but also challenging in terms of time and effort. In this thesis, we will introduce a methodology to support modular quantitative analysis in order to estimate average power of circuits, on the basis of two concepts named Random Bag Preserving and Linear Compositionality. It can shorten simulation time and sustain high accuracy, resulting in increasing the feasibility of power estimation of big systems. For power saving, firstly, we take advantages of the low power characteristic of adiabatic logic and asynchronous logic to achieve ultra-low dynamic and static power. We will propose two memory cells, which could run in adiabatic and non-adiabatic mode. About 90% dynamic power can be saved in adiabatic mode when compared to other up-to-date designs. About 90% leakage power is saved. Secondly, a novel logic, named Asynchronous Charge Sharing Logic (ACSL), will be introduced. The realization of completion detection is simplified considerably. Not just the power reduction improvement, ACSL brings another promising feature in average power estimation called data-independency where this characteristic would make power estimation effortless and be meaningful for modular quantitative average case analysis. Finally, a new asynchronous Arithmetic Logic Unit (ALU) with a ripple carry adder implemented using the logically reversible/bidirectional characteristic exhibiting ultra-low power dissipation with sub-threshold region operating point will be presented. The proposed adder is able to operate multi-functionally

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

Analysis of Various DCVSL Structures and Implementation of Full Adder with Them

The Differential Cascode Voltage Switch Logic (DCVSL) is a CMOS circuit technique which has potential advantages over conventional NAND/NOR logic in terms of power dissipation, circuit delay, layout density and logic flexibility. In this paper, a detailed comparison of all the DCVSL structures are provided including the implementation of Full Adder circuit with the help of those DCVSL structures, which includes Static DCVSL, Dynamic DCVSL and Modified DCVSL. The performance analysis is done in Cadence Virtuoso 90nm CMOS Technology. The working of these DCVSL structures is based on the concept of ‘Multiplexer’. A multiplexer also known as ‘mux’, which is a device where from a number of input signals, selection is done. It is basically a combinational logic circuit. The multiplexer is a unidirectional device, which is used in applications where a data must be switched from multiple sources to a destination. The analysis of all these DCVSL structures is followed by the implementation of Full Adder. Adders are the building blocks in computer systems. Digital Computer Systems widely uses Arithmetic operations. Addition is a necessary arithmetic operation, which is also the root for arithmetic operation such as multiplication. Similarly, adding another XOR gate, the basic adder cell can be modified to function as subtractor, which can be used for division. Therefore, 1-bit Full Adder cell is the ultimate and simple block of an arithmetic unit of a system. So, the basic 1-bit Full Adder cell must be improved, so that the performance of the digital circuits. In VLSI, there is always a trade-off between speed and power dissipation. One parameter is improved, the other gets degraded. Hence, the parameter power delay product is introduced. So, to achieve speeds, high drivability hybrid-DCVSL design methodologies are used to build adder cell in this work. The DCVSL gates produces both complementary and true outputs using single gate architecture. And, the multipliers in the design are based on the pass transistor logic (PTL), because these occupies less chip area per component and also are simple to construct. The parameters compared are power dissipation, propagation delay time, power delay product, transistor number and power dissipation (average). The Static DCVSL structure produces best result in terms of power dissipation, delay and power delay product. Whereas, in case of the Adder circuit, the power consumption is best for the Dynamic DCVSL Adder, along with the delay and the power delay product for the output Sum; but for the output Cout, the best option is Static DCVSL Adder, as the delay and the power delay product is least in this case

Asynchronous design of a multi-dimensional logarithmic number system processor for digital hearing instruments.

This thesis presents an asynchronous Multi-Dimensional Logarithmic Number System (MDLNS) processor that exhibits very low power dissipation. The target application is for a hearing instrument DSP. The MDLNS is a newly developed number system that has the advantage of reducing hardware complexity compared to the classical Logarithmic Number System (LNS). A synchronous implementation of a 2-digit 2DLNS filterbank, using the MDLNS to construct a FIR filterbank, has successfully proved that this novel number representation can benefit this digital hearing instrument application in the requirement of small size and low power. In this thesis we demonstrate that the combination of using the MDLNS, along with an asynchronous design methodology, produces impressive power savings compared to the previous synchronous design. A 4-phase bundled-data full-handshaking protocol is applied to the asynchronous control design. We adopt the Differential Cascade Voltage Switch Logic (DCVSL) circuit family for the design of the computation cells in this asynchronous MDLNS processor. Besides the asynchronous design methodology, we also use finite ring calculations to reduce adder bit-width to provide improvements compared to the previous MDLNS filterbank architecture. Spectre power simulation results from simulations of this asynchronous MDLNS processor demonstrate that over 70 percent power savings have been achieved compared to the synchronous design. This full-custom asynchronous MDLNS processor has been submitted for fabrication in the TSMC 0.18mum CMOS technology. A further contribution in this thesis is the development of a novel synchronizing method of design for testability (DfT), which is offered as a possible solution for asynchronous DfT methods.Dept. of Electrical and Computer Engineering. Paper copy at Leddy Library: Theses & Major Papers - Basement, West Bldg. / Call Number: Thesis2004 .W85. Source: Masters Abstracts International, Volume: 43-01, page: 0288. Advisers: G. A. Jullien; W. C. Miller. Thesis (M.A.Sc.)--University of Windsor (Canada), 2004

Design and Implementation of Novel High Performance Domino Logic

This dissertation presents design and implementation of novel high performance domino logic techniques with increased noise robustness and reduced leakages. The speed and overhead area became the primary parameters of choice for fabrication industry that led to invention of clocked logic styles named as Dynamic logic and Domino logic families. Most importantly, power consumption, noise immunity, speed of operation, area and cost are the predominant parameters for designing any kind of digital logic circuit technique with effective trade-off amongst these parameters depending on the situation and application of design. Because of its high speed and low overhead area domino logic became process of choice for designing of high speed application circuits. The concerning issues are large power consumption and high sensitivity towards noise. Hence, there is a need for designing new domino methodology to meet the requirements by overcoming above mentioned drawbacks which led to ample opportunities for diversified research in this field. Therefore, the outcome of research must be able to handle the primary design parameters efficiently. Besides this, the designed circuit must exhibit high degree of robustness towards noise.In this thesis, few domino logic circuit techniques are proposed to deal with noise and sub-threshold leakages. Effect of signal integrity issues on domino logic techniques is studied. Furthermore, having been subjected to process corner analysis and noise analysis, the overall performance of proposed domino techniques is found to be enhanced despite a few limitations that are mentioned in this work. Besides this, lector based domino and dynamic node stabilized techniques are also proposed and are investigated thoroughly. Simulations show that proposed circuits are showing superior performance. In addition to this, domino based Schmitt triggers with various hysteresis phenomena are designed and simulated. Pre-layout and post-layout simulation results are compared for proposed Schmitt trigger. Simulations reveal that proposed Schmitt trigger techniques are more noise tolerant than CMOS counterparts. Moreover, a test chip for domino based Schmitt trigger is done in UMC 180 nm technology for fabrication

Optimal digital system design in deep submicron technology

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2006.Includes bibliographical references (p. 165-174).The optimization of a digital system in deep submicron technology should be done with two basic principles: energy waste reduction and energy-delay tradeoff. Increased energy resources obtained through energy waste reduction are utilized through energy-delay tradeoffs. The previous practice of obliviously pursuing performance has led to the rapid increase in energy consumption. While energy waste due to unnecessary switching could be reduced with small increases in logic complexity, leakage energy waste still remains as a major design challenge. We find that fine-grain dynamic leakage reduction (FG-DLR), turning off small subblocks for short idle intervals, is the key for successful leakage energy saving. We introduce an FG-DLR circuit technique, Leakage Biasing, which uses leakage currents themselves to bias the circuit into the minimum leakage state, and apply it to primary SRAM arrays for bitline leakage reduction (Leakage-Biased Bitlines) and to domino logic (Leakage-Biased Domino). We also introduce another FG-DLR circuit technique, Dynamic Resizing, which dynamically downsizes transistors on idle paths while maintaining the performance along active critical paths, and apply it to static CMOS circuits.(cont.) We show that significant energy reduction can be achieved at the same computation throughput and communication bandwidth by pipelining logic gates and wires. We find that energy saved by pipelining datapaths is eventually limited by latch energy overhead, leading to a power-optimal pipelining. Structuring global wires into on-chip networks provides a better environment for pipelining and leakage energy saving. We show that the energy-efficiency increase through replacement with dynamically packet-routed networks is bounded by router energy overhead. Finally, we provide a way of relaxing the peak power constraint. We evaluate the use of Activity Migration (AM) for hot spot removal. AM spreads heat by transporting computation to a different location on the die. We show that AM can be used either to increase the power that can be dissipated by a given package, or to lower the operating temperature and hence the operating energy.by Seongmoo Heo.Ph.D

An ultra-low voltage FFT processor using energy-aware techniques

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, February 2004.Page 170 blank.Includes bibliographical references (p. 165-169).In a number of emerging applications such as wireless sensor networks, system lifetime depends on the energy efficiency of computation and communication. The key metric in such applications is the energy dissipated per function rather than traditional ones such as clock speed or silicon area. Hardware designs are shifting focus toward enabling energy-awareness, allowing the processor to be energy-efficient for a variety of operating scenarios. This is in contrast to conventional low-power design, which optimizes for the worst-case scenario. Here, three energy-quality scalable hooks are designed into a real-valued FFT processor: variable FFT length (N=128 to 1024 points), variable bit precision (8,16 bit), and variable voltage supply with variable clock frequency (VDD=1 80mV to 0.9V, and f=164Hz to 6MHz). A variable-bit-precision and variable-FFT-length scalable FFT ASIC using an off-the-shelf standard-cell logic library and memory only scales down to 1V operation. Further energy savings is achieved through ultra-low voltage-supply operation. As performance requirements are relaxed, the operating voltage supply is scaled down, possibly even below the threshold voltage into the subthreshold region. When lower frequencies cause leakage energy dissipation to exceed the active energy dissipation, there is an optimal operating point for minimizing energy consumption.(cont.) Logic and memory design techniques allowing ultra-low voltage operation are employed to study the optimal frequency/voltage operating point for the FFT. A full-custom implementation with circuit techniques optimized for deep voltage scaling into the subthreshold regime, is fabricated using a standard CMOS 0.18[mu]m logic process and functions down to 180mV. At the optimal operating point where the voltage supply is 350mV, the FFT processor dissipates 155nJ/FFT. The custom FFT is 8x more energy-efficient than the ASIC implementation and 350x more energy-efficient than a low-power microprocessor implementation.by Alice Wang.Ph.D