Continuous time controller based on SMC and disturbance observer for piezoelectric actuators

Abstract – In this work, analog application for the Sliding Mode Control (SMC) to piezoelectric actuators (PEA) is presented. DSP application of the algorithm suffers from ADC and DAC conversions and mainly faces limitations in sampling time interval. Moreover piezoelectric actuators are known to have very large bandwidth close to the DSP operation frequency. Therefore, with the direct analog application, improvement of the performance and high frequency operation are expected. Design of an appropriate SMC together with a disturbance observer is suggested to have continuous control output and related experimental results for position tracking are presented with comparison of DSP and analog control application

Discrete-time sliding mode control of high precision linear drive using frictional model

The paper deals with high precision motion control of linear drive system. The accuracy and behavior of the linear drive system are highly affected by the non-linear frictional component compromising of stiction, viscous and stribeck effect present in the system especially in the vicinity of zero velocity. In order to achieve the high accuracy and motion it is mandatory to drive our system with low velocity resulting in many non linear phenomena like tracking error, limit cycles and undesired stick-slip motion etc. This paper discuss the design and implementation of discrete time sliding mode control along with the implementation of dynamic frictional model in order to estimate and compensate the disturbance arising due to frictional component. Experimental results are presented to illustrate the effectiveness and achievable control performance of the proposed scheme

Scaled bilateral teleoperation using discrete-time sliding mode controller

In this paper, the design of a discrete-time slidingmode controller based on Lyapunov theory is presented along with a robust disturbance observer and is applied to a piezostage for high-precision motion. A linear model of a piezostage was used with nominal parameters to compensate the disturbance acting on the system in order to achieve nanometer accuracy. The effectiveness of the controller and disturbance observer is validated in terms of closed-loop position performance for nanometer references. The control structure has been applied to a scaled bilateral structure for the custom-built telemicromanipulation setup. A piezoresistive atomic force microscope cantilever with a built-in Wheatstone bridge is utilized to achieve the nanonewtonlevel interaction forces between the piezoresistive probe tip and the environment. Experimental results are provided for the nanonewton-range force sensing, and good agreement between the experimental data and the theoretical estimates has been demonstrated. Force/position tracking and transparency between the master and the slave has been clearly demonstrated after necessary scalin

Development of a micromanipulation system with force sensing

This article provides in-depth knowledge about our undergoing effort to develop an open architecture micromanipulation system with force sensing capabilities. The major requirement to perform any micromanipulation task effectively is to ensure the controlled motion of actuators within nanometer accuracy with low overshoot even under the influence of disturbances. Moreover, to achieve high dexterity in manipulation, control of the interaction forces is required. In micromanipulation, control of interaction forces necessitates force sensing in milli-Newton range with nano-Newton resolution. In this paper, we present a position controller based on a discrete time sliding mode control architecture along with a disturbance observer. Experimental verifications for this controller are demonstrated for 100, 50 and 10 nanometer step inputs applied to PZT stages. Our results indicate that position tracking accuracies up to 10 nanometers, without any overshoot and low steady state error are achievable. Furthermore, the paper includes experimental verification of force sensing within nano-Newton resolution using a piezoresistive cantilever endeffector. Experimental results are compared to the theoretical estimates of the change in attractive forces as a function of decreasing distance and of the pull off force between a silicon tip and a glass surface, respectively. Good agreement among the experimental data and the theoretical estimates has been demonstrated

AC voltage regulation of a bidirectional high-frequency link converter using a deadbeat controller

This paper presents a digital controller for AC voltage regulation of a bidirectional high-frequency link (BHFL) inverter using Deadbeat control. The proposed controller consists of inner current loop, outer voltage loop and a feed-forward controller, which imposes a gain scheduling effect according to the reference signal to compensate the steady-state error of the system. The main property of the proposed controller is that the current- and the voltage-loop controllers have the same structure, and use the same sampling period. This simplifies the design and implementation processes. To improve the overall performance of the system, additional disturbance decoupling networks are employed. This takes into account the model discretization effect. Therefore, accurate disturbance decoupling can be achieved, and the system robustness towards load variations is increased. To avoid transformer saturation due to low frequency voltage envelopes, an equalized pulse width modulation (PWM) technique has been introduced. The proposed controller has been realized using the DS1104 digital signal processor (DSP) from dSPACE. Its performances have been tested on a one kVA prototype inverter. Experimental results showed that the proposed controller has very fast dynamic and good steady-state responses even under highly nonlinear loads

Second-order SM approach to SISO time-delay system output tracking

A fully linearizable single-input-single-output relative-degree n system with an output time delay is considered in this paper. Using the approach of Pade approximation, system center approach, and second-order sliding-mode (SM) control, we have obtained good output tracking results. The Smith predictor is used to compensate the difference between the actual delayed output and its approximation. A second-order supertwisting SM observer observes the disturbance in the plant. A nonlinear example is studied to show the effect of this methodology

Optimal control design for robust fuzzy friction compensation in a robot joint

This paper presents a methodology for the compensation of nonlinear friction in a robot joint structure based on a fuzzy local modeling technique. To enhance the tracking performance of the robot joint, a dynamic model is derived from the local physical properties of friction. The model is the basis of a precompensator taking into account the dynamics of the overall corrected system by means of a minor loop. The proposed structure does not claim to faithfully reproduce complex phenomena driven by friction. However, the linearity of the local models simplifies the design and implementation of the observer, and its estimation capabilities are improved by the nonlinear integral gain. The controller can then be robustly synthesized using linear matrix inequalities to cancel the effects of inexact friction compensation. Experimental tests conducted on a robot joint with a high level of friction demonstrate the effectiveness of the proposed fuzzy observer-based control strategy for tracking system trajectories when operating in zero-velocity regions and during motion reversals

Sliding modes in constrained systems control

Abstract—In this paper, a sliding-mode-based design framework for fully actuated mechanical multibody system is discussed. The framework is based on the possibility to represent complex motion as a collection of tasks and to find effective mapping of the system coordinates that allows decoupling task and constraint control so one is able to enforce concurrently, or in certain time succession, the task and the constraints. The approach seems naturally encompassing the control of motion systems in interaction, and it allows application to bilateral control, multilateral control, etc. Such an approach leads to a more natural interpretation of the system tasks, simpler controller design, and easier establishment of the systems hierarchy. It allows a unified mathematical treatment of task control in the presence of constraints required to be satisfied by the system coordinates. In order to show the applicability of the proposed techniques, simulation and experimental results for high-precision systems in microsystem assembly tasks and bilateral control systems are presented