Position estimation and performance prediction for permanent-magnet motor drives

PhD ThesisThis thesis presents a theoretical and experimental development of a novel position estimator, a simulation model, and an analytical solution for brushless PM motor drive. The operation of the drive, the position estimation model of the test motor, development of hardware, and basic operation of inverter are discussed. Starting with the well-known continuous-time model of brushless PM motor, a sampled-data model is developed that is suitable for th6, application of real-time position estimator. An analytical methodo f calculating the steady-stateb ehaviouro f the brushlessP M motor for 1200in verter operation is presentedT. he analysisa ssumesth at the machinea ir gap is free of saliency effects, and has sinusoidal back EMF. The analytical solution is derived for 60" electrical of the whole period. By experimental results, it is shown that the method of analysis is adequate to predict Ihe motor's performance for typical operating points including phase advance and phase delay operation. C) I A computer simulation model for prediction of the performance of brushless PM moto rs is presented. The model is formulated entirely in the natural abc frame of reference, which allows direct comparison of the simulation and corresponding experimental results. The equations and diagrams are put into a convenient form for the simulation and future developments and library modules. The simulation model and corresponding experimental data of the brushless PM motor drive is given. The thesis describes a modem solution to real-time rotor position estimation, which has been subject to intense research activity for the last 15 years. The implemented new algorithm for shaft position sensorless operation of PM motors is based on the flux linkage and line current estimation. The position estimation algorithm has also been verified by both off-line and on-line experiments (accomplished by a DSP, TMS320C30), and a wide range of steady-statea nd transient results have been 0gi0v en including starting from rest. The position estimation method effectively moves the position measurement point in the drive from the mechanical side to the motor's terminals. As well as eliminating the mechanical shaft position sensor, the investigated method can be used for high performance torque control of brushless PM motors. The thesis demonstrates that, in contrast to many other "sensorless" schemes, the new position estimation method is able to work effectively over the full operating range of the drive, and is applicable to a wide range of motor/converter types. Since the hardware is straightforward, only the new position estimation algorithm differentiates a system. Therefore, if a DSP control system is already implemented in the drive, the position estimator can be implemented at low cost.Istanbul Technical University and Higher Education Counci

Precision Control of a Sensorless Brushless Direct Current Motor System

Sensorless control strategies were first suggested well over a decade ago with the aim of reducing the size, weight and unit cost of electrically actuated servo systems. The resulting algorithms have been successfully applied to the induction and synchronous motor families in applications where control of armature speeds above approximately one hundred revolutions per minute is desired. However, sensorless position control remains problematic. This thesis provides an in depth investigation into sensorless motor control strategies for high precision motion control applications. Specifically, methods of achieving control of position and very low speed thresholds are investigated. The developed grey box identification techniques are shown to perform better than their traditional white or black box counterparts. Further, fuzzy model based sliding mode control is implemented and results demonstrate its improved robustness to certain classes of disturbance. Attempts to reject uncertainty within the developed models using the sliding mode are discussed. Novel controllers, which enhance the performance of the sliding mode are presented. Finally, algorithms that achieve control without a primary feedback sensor are successfully demonstrated. Sensorless position control is achieved with resolutions equivalent to those of existing stepper motor technology. The successful control of armature speeds below sixty revolutions per minute is achieved and problems typically associated with motor starting are circumvented.Research Instruments Ltd

Analysis and implimentation of radial basis function neural network for controlling non-linear dynamical systems

PhD ThesisModelling and control of non-linear systems are not easy, which are now being solved by the application of neural networks. Neural networks have been proved to solve these problems as they are described by adjustable parameters which are readily adaptable online. Many types of neural networks have been used and the most common one is the backpropagation algorithm. The algorithm has some disadvantages, such as slow convergence and construction complexity. An alternative neural networks to overcome the limitations associated with the backpropagation algorithm is the Radial Basis Function Network which has been widely used for solving many complex problems. The Radial Basis Function Network is considered in this theses, along with a new adaptive algorithm which has been developed to overcome the problem of the optimum parameter selection. Use of the new algorithm reduces the trial and error of selecting the minimum required number of centres and guarantees the optimum values of the centres, the widths between the centres and the network weights. Computer simulation usmg SimulinklMatlab packages, demonstrated the results of modelling and control of non-linear systems. Moreover, the algorithm is used for selecting the optimum parameters of a non-linear real system 'Brushless DC Motor'. In the laboratory implementation satisfactory results have been achieved, which show that the Radial Basis Function may be used for modelling and on-line control of such real non-linear systems.The Libyan Ministry of Higher Education

Active torque ripple reduction in permanent-magnet AC motors

Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1995.Includes bibliographical references (leaves 101-104).by Christopher Anthony Greamo.M.S

Windings fault detection and prognosis in electro-mechanical flight control actuators operating in active-active configuration

One of the most significant research trends in the last decades of the aeronautic industry is the effort to move towards the design and the production of “more electric aircraft”. Within this framework, the application of the electrical technology to flight control systems has seen a progressive, although slow, increase: starting with the introduction of fly-by-wire and proceeding with the partial replacement of the traditional hydraulic/electro-hydraulic actuators with purely electro-mechanical ones. This evolution allowed to obtain more flexible solutions, reduced installation issues and enhanced aircraft control capability.Electro-Mechanical Actuators (EMAs) are however far from being a mature technology and still suffer from several safety issues, which can be partially limited by increasing the complexity of their design and hence their production costs. The development of a robust Prognostics and Health Management (PHM) system could provide a way to prevent the occurrence of a critical failure without resorting to complex device design. This paper deals with the first part of the study of a comprehensive PHM system for EMAs employed as primary flight control actuators; the peculiarities of the application are presented and discussed, while a novel approach, based on short pre-flight/post-flight health monitoring tests, is proposed. Turn-to-turn short in the electric motor windings is identified as the most common electrical degradation and a particle filtering framework for anomaly detection and prognosis featuring a self-tuning non-linear model is proposed. Features, anomaly detection and a prognostic algorithm are hence evaluated through state-of-the art performance metrics and their results discussed

A HEL testbed for high accuracy beam pointing and control

High energy laser (HEL) weapons are some of most challenging military applications in the future battle fields since the speed of light delivery enables the war fighter to engage very distant targets immediately. The issues of the technology on the HEL system include various types of high energy laser devices, beam control systems, atmospheric propagation, and target lethality. Among them, precision pointing of laser beam and high-bandwidth rejection of jitters produced by platform vibrations are one of the key technologies for the emerging fields of laser communications and HEL systems. HEL testbed has been developed to support the research environments on the precision beam control technology including acquisition, tracking, and pointing. The testbed incorporates optical table, two axis gimbal, high speed computers, and a variety of servo components, sensors, optical components, and software. In this report, system configuration and operation modes of the testbed are briefly introduced. The results of the experiments and integrated modeling from component to system level are described and discussed. Based on these results, new control algorithms are designed and it is shown that the algorithm can improve the pointing performance of the system.Approved for public release; distribution is unlimited

Passive Stability And Actuation Of Micro Aerial Vehicles

Micro Aerial Vehicles (MAVs) have increased in popularity in recent years. The most common platform, the quadrotor, has surpassed other MAVs like traditional helicopters and ornithopters in popularity mainly due to their simplicity. Yet the quadrotor design is a century old and was intended to carry people. We set out to design a MAV that is designed specifically to be a MAV, i.e. a vehicle not intended to carry humans as a payload. With this constraint lifted the vehicle can continuously rotate, which would dizzy a human, can sustain larger forces, which would damage a human, or can take advantage of scaling properties, where it may not work at human scale. Furthermore, we aim for simplicity by removing vehicle controllers and reducing the number of actuators, such that the vehicle can be made cost effective, if not disposable. We begin by studying general equations of motion for hovering MAVs. We search for vehicle configurations that exhibit passive stability, allowing the MAV to operate without a controller or actuators to apply control, ideally a single actuator. The analysis suggests two distinct types of passively stabilized MAVs and we create test vehicles for both. With simple hovering achieved, we concentrate on controlled motion with an emphasis on doing so without adding actuators. We find we can attain three degree of freedom control using separation of time scales with our actuator via low frequency for control in the vertical direction and high frequency for control in the horizontal plane. We explore techniques for achieving high frequency actuator control, which also allow the compensation of motor defects, specifically cogging torque. We combine passive stability with the motion control into two vehicles, UNO and Piccolissimo. UNO, the Underactuated-propeller Naturally-stabilized One-motor vehicle, demonstrates the capabilities of simple vehicles by performing maneuvers like conventional quadrotors. Piccolissimo, Italian for “very little”, demonstrates the merits of passive stability and single actuator control by being the smallest, self-powered, controllable MAV