Three-Phase Induction Motor Speed Estimation Using Recurrent Neural Network

In induction motor speed control method, the development of the field-oriented control (FOC) algorithm which can control torque and flux separately enables the motor to replace many roles of DC motors. Induction motor speed control can be done by using a close loop system which requires a speed sensor. Referring to the speed sensor weaknesses such as less accurate of the measurement, this is due to the placement of the sensor system that is too far from the control system. Therefore, a speed sensorless method was developed which has various advantages. In this study, the speed sensorless method using an artificial neural network with recurrent neural network (RNN) as speed observer on three-phase induction motor has been discussed. The RNN can maintain steady-state conditions against a well-defined set point speed, so that the observer is able and will be suitable if applied as input control for the motor drives. In this work, the RNN has successfully estimated the rotor flux of the induction motor in MATLAB R2019a simulation as about 0.0004Wb. As based on speed estimation error, the estimator used has produced at about 26.77%, 8.7% and 6.1% for 150rad/s, 200rad/s and 250rad/s respectively. The future work can be developed and improved by creating a prototype system of the induction motor to get more accurate results in real-time of the proposed RNN observer

DTC based on SVM for induction motor sensorless drive with fuzzy sliding mode speed controller

By using the direct torque control (DTC), robust response in ac drives can be produced. Ripples of currents, torque and flux are oberved in steady state. space vector modulation (SVM) applied in DTC and used for a sensorless induction motor (IM) with fuzzy sliding mode speed controller (FSMSC) is studied in this paper. This control can minimize the torque, flux, current and speed pulsations in steady state. To estimate the rotor speed and stator flux the model reference adaptive system (MRAS) is used that is designed from identified voltages and currents. The FSMSC is used to enhance the efficiency and the robustness of the presented system. The DTC transient advantage are maintained, while better quality steady-state performance is produced in sensorless implementation for a wide speed range. The drive system performances have been checked by using Matlab Simultaion, and successful results have been obtained. It is deduced that the proposed control system produces better results than the classical DTC

Vector Control of Asynchronous Motor of Drive Train Using Speed Controller H∞

This study proposes the speed control of an asynchronous motor (AM) using the Antiwindup design. First, the conventional vector control based on proportional-integral (PI) controllers is developed for a constant speed set point. Then, a driving cycle is based on measurements on the Safi/Rabat motorway in Morocco using a microcontroller equipped with a GPS device. The collected practical speed is used as a speed reference for conventional vector control. The /Antiwindup controller of the direct rotor flow-oriented control is used to improve the performance of conventional vector control and optimize the energy consumption of the drive train. The effectiveness of the proposed control scheme is verified by numerical simulation. The results of the numerical validation of the proposed scheme showed good performance compared to conventional vector control. The speed control systems are analyzed for different operating conditions. These control strategies are simulated in the MATLAB/SIMULINK environment. The simulation results of the improved vector control of the Asynchronous Machine (AM) are used to validate this optimization approach in the dynamic regime, followed by a comparative analysis to evaluate the performance and effectiveness of the proposed approach. A practical model based on a TMS320F28379D embedded board and its reduced voltage inverter (24V) is used to implement the proposed method and verify the simulation results. Doi: 10.28991/ESJ-2022-06-04-012 Full Text: PD

Torque Control

This book is the result of inspirations and contributions from many researchers, a collection of 9 works, which are, in majority, focalised around the Direct Torque Control and may be comprised of three sections: different techniques for the control of asynchronous motors and double feed or double star induction machines, oriented approach of recent developments relating to the control of the Permanent Magnet Synchronous Motors, and special controller design and torque control of switched reluctance machine

Observer-based Fault Detection and Diagnosis for Mechanical Transmission Systems with Sensorless Variable Speed Drives

Observer based approaches are commonly embedded in sensorless variable speed drives for the purpose of speed control. It estimates system variables to produce errors or residual signals in conjunction with corresponding measurements. The residual signals then are relied to tune control parameters to maintain operational performance even if there are considerable disturbances such as noises and component faults. Obviously, this control strategy outcomes robust control performances. However, it may produce adverse consequences to the system when faults progress to high severity. To prevent the occurrences of such consequences, this research proposes the utilisation of residual signals as detection features to raise alerts for incipient faults. Based on a gear transmission system with a sensorless variable speed drive (VSD), observers for speed, flux and torque are developed for examining their residuals under two mechanical faults: tooth breakage with different degrees of severities and shortage of lubricant at different levels are investigated. It shows that power residual signals can be based on to indicate different faults, showing that the observer based approaches are effective for monitoring VSD based mechanical systems. Moreover, it also shows that these two types fault can be separated based on the dynamic components in the voltage signals

A general magnetic-energy-based torque estimator: validation via a permanent-magnet motor drive

This paper describes the use of the current–flux-linkage ($i{-}psi$ ) diagram to validate the performance of a general magnetic-energy-based torque estimator. An early step in the torque estimation is the use of controller duty cycles to reconstruct the average phase-voltage waveform during each pulsewidth-modulation (PWM) switching period. Samples over the fundamental period are recorded for the estimation of the average torque. The fundamental period may not be an exact multiple of the sample time. For low speed, the reconstructed voltage requires additional compensation for inverter-device losses. Experimental validation of this reconstructed waveform with the actual PWM phase-voltage waveform is impossible due to the fact that one is PWM in nature and the other is the average value during the PWM period. A solution to this is to determine the phase flux-linkage using each waveform and then plot the resultant $i{-}psi$ loops. The torque estimation is based on instantaneous measurements and can therefore be applied to any electrical machine. This paper includes test results for a three-phase interior permanent-magnet brushless ac motor operating with both sinusoidal and nonsinusoidal current waveforms

Zero Speed Rotor Position Estimator based on Sliding Mode Control for Permanent Magnet Synchronous Motor

The permImplementation of an algorithm based on SMC that uses a unique technique for the rotor position estimation of a PMSM for low and zero speeds, by using inherit motor effect called "Saliency". The work proves that the rotor position estimation is possible with the information that is present in the system under SMC due to the saliency effect. Therefore, there is no need to inject any signal into the machine, which causes the increment in the losses of the machine, or to design dynamic observers. The algorithm is implemented in a DSP controller and the tests with the complete hardware platform validate the proposal in open loop and in sensorless operation

A review of saliency-based sensorless control methods for alternating current machines

Operation of model-based sensorless control of Alternating Current machines at low and zero speeds is unreliable and can fail. To overcome the limitations of sensorless control at low speeds, several alternative techniques have been developed to estimate speed and position. These are mainly based on detecting machine saliencies by measuring the response of the current to some form of voltage injection. This paper discusses injection methods, machine saliencies, and techniques used to extract speed and position that are applicable to both induction machines and permanent magnet synchronous motors.peer-reviewe