Controller Synthesis of Multi-Axial Robotic System Used for Wearable Devices

Wearable devices are commonly used in different fields to help improving performance of movements for different groups of users. The long-term goal of this study is to develop a low-cost assistive robotic device that allows patients to perform rehabilitation activities independently and reproduces natural movement to help stroke patients and elderly adults in their daily activities while moving their arms. In the past few decades, various types of wearable robotic devices have been developed to assist different physical movements. Among different types of actuators, the twisted-string actuation system is one of those that has advantages of light-weight, low cost, and great portability. In this study, a dual twisted-string actuator is used to drive the joints of the prototype assistive robotic device. To compensate the asynchronous movement caused by nonlinear factors, a hybrid controller that combines fuzzy logic rules and linear PID control algorithm was adopted to compensate for both tracking and synchronization of the two actuators.;In order to validate the performance of proposed controllers, the robotic device was driven by an xPC Target machine with additional embedded controllers for different data acquisition tasks. The controllers were fine tuned to eliminate the inaccuracy of tracking and synchronization caused by disturbance and asynchronous movements of both actuators. As a result, the synthesized controller can provide a high precision when tracking simple actual human movements

Design and Development of a Twisted String Exoskeleton Robot for the Upper Limb

High-intensity and task-specific upper-limb treatment of active, highly repetitive movements are the effective approaches for patients with motor disorders. However, with the severe shortage of medical service in the United States and the fact that post-stroke survivors can continue to incur significant financial costs, patients often choose not to return to the hospital or clinic for complete recovery. Therefore, robot-assisted therapy can be considered as an alternative rehabilitation approach because the similar or better results as the patients who receive intensive conventional therapy offered by professional physicians.;The primary objective of this study was to design and fabricate an effective mobile assistive robotic system that can provide stroke patients shoulder and elbow assistance. To reduce the size of actuators and to minimize the weight that needs to be carried by users, two sets of dual twisted-string actuators, each with 7 strands (1 neutral and 6 effective) were used to extend/contract the adopted strings to drive the rotational movements of shoulder and elbow joints through a Bowden cable mechanism. Furthermore, movements of non-disabled people were captured as templates of training trajectories to provide effective rehabilitation.;The specific aims of this study included the development of a two-degree-of-freedom prototype for the elbow and shoulder joints, an adaptive robust control algorithm with cross-coupling dynamics that can compensate for both nonlinear factors of the system and asynchronization between individual actuators as well as an approach for extracting the reference trajectories for the assistive robotic from non-disabled people based on Microsoft Kinect sensor and Dynamic time warping algorithm. Finally, the data acquisition and control system of the robot was implemented by Intel Galileo and XILINX FPGA embedded system

Elbow exoskeleton mechanism for multistage poststroke rehabilitation.

More than three million people are suffering from stroke in England. The process of post-stroke rehabilitation consists of a series of biomechanical exercises- controlled joint movement in acute phase; external assistance in the mid phase; and variable levels of resistance in the last phase. Post-stroke rehabilitation performed by physiotherapist has many limitations including cost, time, repeatability and intensity of exercises. Although a large variety of arm exoskeletons have been developed in the last two decades to substitute the conventional exercises provided by physiotherapist, most of these systems have limitations with structural configuration, sensory data acquisition and control architecture. It is still difficult to facilitate multistage post-stroke rehabilitation to patients sited around hospital bed without expert intervention. To support this, a framework for elbow exoskeleton has been developed that is portable and has the potential to offer all three types of exercises (external force, assistive and resistive) in a single structure. The design enhances torque to weight ratio compared to joint based actuation systems. The structural lengths of the exoskeleton are determined based on the mean anthropometric parameters of healthy users and the lengths of upperarm and forearm are determined to fit a wide range of users. The operation of the exoskeleton is divided into three regions where each type of exercise can be served in a specific way depending on the requirements of users. Electric motor provides power in the first region of operation whereas spring based assistive force is used in the second region and spring based resistive force is applied in the third region. This design concept provides an engineering solution of integrating three phases of post-stroke exercises in a single device. With this strategy, the energy source is only used in the first region to power the motor whereas the other two modes of exercise can work on the stored energy of springs. All these operations are controlled by a single motor and the maximum torque of the motor required is only 5 Nm. However, due to mechanical advantage, the exoskeleton can provide the joint torque up to 10 Nm. To remove the dependency on biosensor, the exoskeleton has been designed with a hardware-based mechanism that can provide assistive and resistive force. All exoskeleton components are integrated into a microcontroller-based circuit for measuring three joint parameters (angle, velocity and torque) and for controlling exercises. A user-friendly, multi-purpose graphical interface has been developed for participants to control the mode of exercise and it can be managed manually or in automatic mode. To validate the conceptual design, a prototype of the exoskeleton has been developed and it has been tested with healthy subjects. The generated assistive torque can be varied up to 0.037 Nm whereas resistive torque can be varied up to 0.057 Nm. The mass of the exoskeleton is approximately 1.8 kg. Two comparative studies have been performed to assess the measurement accuracy of the exoskeleton. In the first study, data collected from two healthy participants after using the exoskeleton and Kinect sensor by keeping Kinect sensor as reference. The mean measurement errors in joint angle are within 5.18 % for participant 1 and 1.66% for participant 2; the errors in torque measurement are within 8.48% and 7.93% respectively. In the next study, the repeatability of joint measurement by exoskeleton is analysed. The exoskeleton has been used by three healthy users in two rotation cycles. It shows a strong correction (correlation coefficient: 0.99) between two consecutive joint angle measurements and standard deviation is calculated to determine the error margin which comes under acceptable range (maximum: 8.897). The research embodied in this thesis presents a design framework of a portable exoskeleton model for providing three modes of exercises, which could provide a potential solution for all stages of post- stroke rehabilitation

Development of an integrated robotic polishing system

This thesis presents research carried out as part of a project undertaken in fulfilment of the requirements of Loughborough University for the award of Philosophical Doctorate. The main focus of this research is to investigate and develop an appropriate level of automation to the existing manual finishing operations of small metallic components to achieve required surface quality and to remove superficial defects. In the manufacturing industries, polishing processes play a vital role in the development of high precision products, to give a desired surface finish, remove defects, break sharp edges, extend the working life cycle, and meet mechanical specification. The polishing operation is generally done at the final stage of the manufacturing process and can represent up to a third of the production time. Despite the growth automated technology in industry, polishing processes are still mainly carried out manually, due to the complexity and constraints of the process. Manual polishing involves a highly qualified worker polishing the workpiece by hand. These processes are very labour intensive, highly skill dependent, costly, error-prone, environmentally hazardous due to abrasive dust, and - in some cases - inefficient with long process times. In addition, the quality of the finishing is dependent on the training, experience, fatigue, physical ability, and expertise of the operator. Therefore, industries are seeking alternative solutions to be implemented within their current processes. These solutions are mainly aimed at replacing the human operator to improve the health and safety of their workforce and improve their competitiveness. Some automated solutions have already been proposed to assist or replace manual polishing processes. These solutions provide limited capabilities for specific processes or components, and a lack of flexibility and dexterity. One of the reasons for their lack of success is identified as neglecting the study and implementing the manual operations. This research initially hypothesised that for an effective development, an automated polishing system should be designed based on the manual polishing operations. Therefore, a successful implementation of an automated polishing system requires a thorough understanding of the polishing process and their operational parameters. This study began by collaborating with an industrial polishing company. The research was focused on polishing complex small components, similar to the parts typically used in the aerospace industry. The high level business processes of the polishing company were capture through several visits to the site. The low level operational parameters and the understanding of the manual operations were also captured through development of a devices that was used by the expert operators. A number of sensors were embedded to the device to facilitate recording the manual operations. For instance, the device captured the force applied by the operator (avg. 10 N) and the cycle time (e.g. 1 pass every 5 sec.). The capture data was then interpreted to manual techniques and polishing approaches that were used in developing a proof-of-concept Integrated Robotic Polishing System (IRPS). The IRPS was tested successfully through several laboratory based experiments by expert operators. The experiment results proved the capability of the proposed system in polishing a variety of part profiles, without pre-existing geometrical information about the parts. One of the main contributions made by this research is to propose a novel approach for automated polishing operations. The development of an integrated robotic polishing system, based on the research findings, uses a set of smart sensors and a force-position-by-increment control algorithm, and transpose the way that skilled workers carry out polishing processes

A steady state tip control strategy for long reach robots

The work presented in this thesis describes the development of a novel strategy for the steady state tip position control of a single link flexible robot arm. Control is based upon a master/slave relationship. Arm trajectory is defined by through 'master' positioning head which moves a laser through a programmed path. Tip position is detected by an optical system which produces an error signal proportional to the displacement of the tip from the demand laser spot position. The error signal and its derivative form inputs to the arm 'slave' controller so enabling direct tip control with simultaneous correction for arm bending. Trajectory definition is not model-based as it is defined optically through movement of the positioning head alone. A critical investigation of vacuum tube and solid state sensing methods is undertaken leading to the development of a photodiode quadrant detector beam tracking system. The effect of varying the incident light parameters on the beam tracker performance are examined from which the optimum illumination characteristics are determined. Operational testing of the system on a dual-axis prototype robot using the purpose-built beam tracker has shown that successful steady state tip control can be achieved through a PD based slave controller. Errors of less than 0.05 mm and settling times of 0.2 s are obtained. These results compare favourably with those for the model-based tip position correction strategies where tracking errors of ± 0.6 mm are recorded

Bio-inspired soft robotic systems: Exploiting environmental interactions using embodied mechanics and sensory coordination

Despite the widespread development of highly intelligent robotic systems exhibiting great precision, reliability, and dexterity, robots remain incapable of performing basic manipulation tasks that humans take for granted. Manipulation in unstructured environments continues to be acknowledged as a significant challenge. Soft robotics, the use of less rigid materials in robots, has been proposed as one means of addressing these limitations. The technique enables more compliant interactions with the environment, allowing for increasingly adaptive behaviours better suited to more human-centric applications. Embodied intelligence is a biologically inspired concept in which intelligence is a function of the entire system, not only the controller or `brain'. This thesis focuses on the use of embodied intelligence for the development of soft robots, with a particular focus on how it can aid both perception and adaptability. Two main hypotheses are raised: first, that the mechanical design and fabrication of soft-rigid hybrid robots can enable increasingly environmentally adaptive behaviours, and second, that sensing materials and morphology can provide intelligence that assists perception through embodiment. A number of approaches and frameworks for the design and development of embodied systems are presented that address these hypotheses. It is shown how embodiment in soft sensor morphology can be used to perform localised processing and thereby distribute the intelligence over the body of a system. Specifically in soft robots, sensor morphology utilises the directional deformations created by interactions with the environment to aid in perception. Building on and formalising these ideas, a number of morphology-based frameworks are proposed for detecting different stimuli. The multifaceted role of materials in soft robots is demonstrated through the development of materials capable of both sensing and changes in material property. Such materials provide additional functionality beyond their integral scaffolding and static mechanical characteristics. In particular, an integrated material has been created exhibiting both sensing capabilities and also variable stiffness and `tack’ force, thereby enabling complex single-point grasping. To maximise the intelligence that can be gained through embodiment, a design approach to soft robots, `soft-rigid hybrid' design is introduced. This approach exploits passive behaviours and body dynamics to provide environmentally adaptive behaviours and sensing. It is leveraged by multi-material 3D printing techniques and novel approaches and frameworks for designing mechanical structures. The findings in this thesis demonstrate that an embodied approach to soft robotics provides capabilities and behaviours that are not currently otherwise achievable. Utilising the concept of `embodiment' results in softer robots with an embodied intelligence that aids perception and adaptive behaviours, and has the potential to bring the physical abilities of robots one step closer to those of animals and humans.EPSR

Macrobend optical sensing for pose measurement in soft robot arms

This paper introduces a pose-sensing system for soft robot arms integrating a set of macrobend stretch sensors. The macrobend sensory design in this study consists of optical fibres and is based on the notion that bending an optical fibre modulates the intensity of the light transmitted through the fibre. This sensing method is capable of measuring bending, elongation and compression in soft continuum robots and is also applicable to wearable sensing technologies, e.g. pose sensing in the wrist joint of a human hand. In our arrangement, applied to a cylindrical soft robot arm, the optical fibres for macrobend sensing originate from the base, extend to the tip of the arm, and then loop back to the base. The connectors that link the fibres to the necessary opto-electronics are all placed at the base of the arm, resulting in a simplified overall design. The ability of this custom macrobend stretch sensor to flexibly adapt its configuration allows preserving the inherent softness and compliance of the robot which it is installed on. The macrobend sensing system is immune to electrical noise and magnetic fields, is safe (because no electricity is needed at the sensing site), and is suitable for modular implementation in multi-link soft continuum robotic arms. The measurable light outputs of the proposed stretch sensor vary due to bend-induced light attenuation (macrobend loss), which is a function of the fibre bend radius as well as the number of repeated turns. The experimental study conducted as part of this research revealed that the chosen bend radius has a far greater impact on the measured light intensity values than the number of turns (if greater than five). Taking into account that the bend radius is the only significantly influencing design parameter, the macrobend stretch sensors were developed to create a practical solution to the pose sensing in soft continuum robot arms. Henceforward, the proposed sensing design was benchmarked against an electromagnetic tracking system (NDI Aurora) for validation

Design and develop virtual reality games utilising the 'anti‐gravity' arm support for stroke rehabilitation therapy

Approximately 16,000 Australians each year are left with a disability as a direct consequence of stroke. The number of strokes that occur in Australia each year is increasing, putting a strong reliance on home and community based rehabilitation having an increasing role in the rehabilitation process. Strokes are caused by a sudden disruption to the flow of blood to parts of the brain. If an artery is blocked, the brain cells (neurons) cannot make enough energy and will eventually stop working. Stroke affects patients in a number of different ways depending on the severity of the stroke and the type of stroke in which the patient suffers from. There two main types of disabilities that are a result of stroke: hemiplegia and hemiparesis. The project aims to develop a virtual reality application to assist in the rehabilitation of the upper extremities of stoke patients who suffer from hemiparesis. The project will endeavour to design a low cost, home based system that will motivate patients by creating intermediate goals that can be adopted into the rehabilitation process. The project will utilise the 'anti‐gravity' arm support system to lessen the affect of reduced muscle strength and control. The project objectives are to: - Research relevant background information on the effects of stroke. - Research traditional methods of stroke rehabilitation and assessment of rehabilitation progression. - Implement hardware and program for position data acquisition. - Develop virtual reality application for exercise and rehabilitation assessment. The project is based around detecting the movement or the patients arm and creating a computer representation. This has been performed by monitoring the potentiometers on the 'anti‐gravity' arm support utilizing the PIC AXE microcontroller. The microcontroller to converts the signal into a digital integer and transfers them to the computer via a serial link. The games were designed around conventional physiotherapy exercises allowing the user to complete the exercises in a self motivating environment. The games were developed in both 2D and 3D environments utilizing Microsoft's XNA games studio. The project has been successful in accurately representing a user's movement within a virtual environment. This has been tested by use of advance 3D mapping techniques; however the project is still not a stage where it is practical to perform clinical trials