Development of an Eight Channel Waveform Generator for Beam-forming Applications

An eight-channel direct-digital waveform synthesizer has been developed to enable digital beam steering of the transmitted waveform. Built around the Analog Devices AD9910 DDS chip, this eight-channel waveform generator, when used with an eight element linear antenna array, enables the illuminating radiation pattern to be digitally modified on a pulse-to-pulse basis if desired. Developed in support of airborne radar depth-sounding of the polar ice sheets and outlet glaciers, two key benefits of this capability provides include improved surface clutter suppression and more efficient off-nadir illumination for side-looking imaging of the ice-bed interface. Adjusting the starting frequency and phase of the waveform produced by each DDS is analogous to introducing an incremental time delay between otherwise identical chirp waveforms, thus providing the required beam-steering control. Additionally, the AD9910, with a 1-GHz maximum clock frequency, provides amplitude control, both intra-waveform and inter-waveform, for time-sidelobe management and radiation-sidelobe management. An FPGA is used for the management of up to 16 waveforms, zero-pi phase modulation on a per waveform basis, system communication over a serial port, and loading the DDS configuration settings on each system trigger. The board provides matched clock and sync inputs in order to guarantee phase alignment across the multiple DDS chips

실시간 근거리 영상화를 위한 MIMO 역합성 개구 레이더 시스템

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 남상욱.Microwave and millimeter wave (micro/mmW) imaging systems have advantages over other imaging systems in that they have penetration properties over non-metallic structures and non-ionization. However, these systems are commercially applicable in limited areas. Depending on the quality and size of the images, a system can be expensive and images cannot be provided in real-time. To overcome the challenges of the current micro/mmW imaging system, it is critical to suggest a new system concept and prove its potential benefits and hazards by demonstrating the testbed. This dissertation presents Ku1DMIC, a wide-band micro/mmW imaging system using Ku-band and 1D-MIMO array, which can overcome the challenges above. For cost-effective 3D imaging capabilities, Ku1DMIC uses 1D-MIMO array configuration and inverse synthetic aperture radar (ISAR) technique. At the same time, Ku1DMIC supports real-time data acquisition through a system-level design of a seamless interface with frequency modulated continuous wave (FMCW) radar. To show the feasibility of 3D imaging with Ku1DMIC and its real-time capabilities, an accelerated imaging algorithm, 1D-MIMO-ISAR RSA, is proposed and demonstrated. The detailed contributions of the dissertation are as follows. First, this dissertation presents Ku1DMIC – a Ku-band MIMO frequency-modulated continuous-wave (FMCW) radar experimental platform with real-time 2D near-field imaging capabilities. The proposed system uses Ku-band to cover the wider illumination area given the limited number of antennas and uses a fast ramp and wide-band FMCW waveform for rapid radar data acquisition while providing high-resolution images. The key design aspect behind the platform is stability, reconfigurability, and real-time capabilities, which allows investigating the exploration of the system’s strengths and weaknesses. To satisfy the design aspect, a digitally assisted platform is proposed and realized based on an AMD-Xilinx UltraScale+ Radio Frequency System on Chip (RFSoC). The experimental investigation for real-time 2D imaging has proved the ability of video-rate imaging at around 60 frames per second. Second, a waveform digital pre-distortion (DPD) method and calibration method are proposed to enhance the image quality. Even if a clean FMCW waveform is generated with the aid of the optimized waveform generator, the signal will inevitably suffer from distortion, especially in the RF subsystem of the platform. In near-field imaging applications, the waveform DPD is not effective at suppressing distortion in wide-band FMCW radar systems. To solve this issue, the LO-DPD architecture and binary search based DPD algorithm are proposed to make the waveform DPD effective in Ku1DMIC. Furthermore, an image-domain optimization correction method is proposed to compensate for the remaining errors that cannot be eliminated by the waveform DPD. For robustness to various unwanted signals such as noise and clutter signals, two regularized least squares problems are applied and compared: the generalized Tikhonov regularization and the total variation (TV) regularization. Through various 2D imaging experiments, it is confirmed that both methods can enhance the image quality by reducing the sidelobe level. Lastly, the research is conducted to realize real-time 3D imaging by applying the ISAR technique to Ku1DMIC. The realization of real-time 3D imaging using 1D-MIMO array configuration is impactful in that this configuration can significantly reduce the costs of the 3D imaging system and enable imaging of moving objects. To this end, the signal model for the 1D-MIMO-ISAR configuration is presented, and then the 1D-MIMO-ISAR range stacking algorithm (RSA) is proposed to accelerate the imaging reconstruction process. The proposed 1D-MIMO-ISAR RSA can reconstruct images within hundreds of milliseconds while maintaining almost the same image quality as the back-projection algorithm, bringing potential use for real-time 3D imaging. It also describes strategies for setting ROI, considering the real-world situations in which objects enter and exit the field of view, and allocating GPU memory. Extensive simulations and experiments have demonstrated the feasibility and potential benefits of 1D-MIMO-IASR configuration and 1D-MIMO-ISAR RSA.마이크로파 및 밀리미터파(micro/mmW) 영상화 시스템은 비금속 구조 및 비이온화에 비해 침투 특성이 있다는 점에서 다른 이미징 시스템에 비해 장점이 있다. 그러나 이러한 시스템은 제한된 영역에서만 상업적으로 적용되고 있다. 이미지의 품질과 크기에 따라 시스템이 매우 고가일 수 있으며 이미지를 실시간으로 제공할 수 없는 현황이다. 현재의 micro/mmW 이미징 시스템의 문제를 극복하려면 새로운 시스템 개념을 제안하고 테스트베드를 시연하여 잠재적인 이점과 위험을 입증하는 것이 중요하다. 본 논문에서는 Ku-band와 1D-MIMO 어레이를 이용한 광대역 micro/mmW 이미징 시스템인 Ku1DMIC를 제안하여 위와 같은 문제점을 극복할 수 있다. 비용 효율적인 3차원 영상화 기능을 위해 Ku1DMIC는 1D-MIMO 배열 기술과 ISAR(Inverse Synthetic Aperture Radar) 기술을 사용한다. 동시에 Ku1DMIC는 주파수 변조 연속파 (FMCW) 레이더와의 원활한 인터페이스의 시스템 수준 설계를 통해 실시간 데이터 수집을 지원한다. Ku1DMIC를 사용한 3차원 영상화의 구현 및 실시간 기능의 가능성을 보여주기 위해, 2차원 영상화를 위한 1D-MIMO RSA과 3차원 영상화를 위한 1D-MIMO-ISAR RSA가 제안되고 Ku1DMIC에서 구현된다. 따라서, 본 학위 논문의 주요 기여는 Ku-band 1D-MIMO 배열 기반 영상화 시스템 프로토타입을 개발 및 테스트하고, ISAR 기반 3차원 영상화 기능을 검사하고, 실시간 3차원 영상화 가능성을 조사하는 것이다. 이에 대한 세부적인 기여 항목은 다음과 같다. 첫째, 실시간 2D 근거리장 이미징 기능을 갖춘 Ku 대역 MIMO 주파수 변조 연속파(FMCW) 레이더 실험 플랫폼인 Ku1DMIC를 제시한다. 제안하는 시스템은 제한된 수의 안테나에서 더 넓은 조명 영역을 커버하기 위해 Ku 대역을 사용하고 고해상도 이미지를 제공하면서 빠른 레이더 데이터 수집을 위해 고속 램프 및 광대역 FMCW 파형을 사용한다. 플랫폼의 핵심 설계 원칙은 안정성, 재구성 가능성 및 실시간 기능으로 시스템의 강점과 약점을 광범위하게 탐색한다. 설계 원칙을 만족시키기 위해 AMD-Xilinx UltraScale+ RFSoC(Radio Frequency System on Chip)를 기반으로 디지털 지원 플랫폼을 제안하고 구현한다. 실시간 2D 이미징에 대한 실험적 조사는 초당 약 60프레임에서 비디오 속도 이미징의 능력을 입증했다. 둘째, 영상 품질 향상을 위한 파형 디지털 전치왜곡(DPD) 방법과 보정 방법을 제안한다. 최적화된 파형 발생기의 도움으로 깨끗한 FMCW 파형이 생성되더라도 특히 플랫폼의 RF 하위 시스템에서 신호는 필연적으로 왜곡을 겪게된다. 근거리 영상화 응용 분야에서는 파형 DPD는 광대역 FMCW 레이더 시스템의 왜곡을 억제하는 데 효과적이지 않다. 이 문제를 해결하기 위해 Ku1DMIC에서 파형 DPD가 유효하도록 LO-DPD 아키텍처와 이진 탐색 기반 DPD 알고리즘을 제안한다. 또한, 파형 DPD로 제거할 수 없는 나머지 오류를 보상하기 위해 이미지 영역 최적화 보정 방법을 제안한다. 노이즈 및 클러터 신호와 같은 다양한 원치 않는 신호에 대한 견고성을 위해 일반화된 Tikhonov 정규화 및 전체 변동(TV) 정규화라는 두 가지 정규화된 최소 자승 문제를 적용 후 비교한다. 다양한 2차원 영상화 실험을 통해 두 방법 모두 부엽 레벨을 줄여 화질을 향상시킬 수 있음을 확인한다. 마지막으로, ISAR 기법을 2차원 영상 플랫폼에 적용하여 실시간 3차원 영상을 구현하기 위한 연구를 진행한다. 1D-MIMO-ISAR 구성에서 실시간 3D 이미징의 구현은 이러한 구성이 3D 이미징 시스템의 비용을 크게 줄일 수 있다는 점에서 영향력이 있다. 따라서 이 논문에서는 1D-MIMO-ISAR 구성에 대한 이미징 재구성을 가속화하기 위해 1D-MIMO-ISAR 범위 스태킹 알고리즘(RSA)을 제안한다. 제안된 1D-MIMO-ISAR RSA는 널리 알려진 Back-Projection 알고리즘과 거의 동일한 이미지 품질을 유지하면서도 수백 밀리초 이내에 이미지를 재구성함으로써 실시간 영상화에 대한 가능성을 보여준다. 또한 물체가 시야에 들어오고 나가는 실제 상황을 고려하기 위한 ROI 설정, 그리고 메모리 할당에 대한 전략을 설명한다. 광범위한 시뮬레이션과 실험을 통해 1D-MIMO-IASR 구성 및 1D-MIMO-ISAR RSA의 가능성과 잠재적 이점을 확인한다.1 INTRODUCTION 1 1.1 Microwave and millimeter-wave imaging 1 1.2 Imaging with radar system 2 1.3 Challenges and motivation 5 1.4 Outline of the dissertation 8 2 FUNDAMENTAL OF TWO-DIMENSIONAL IMAGING USING A MIMO RADAR 9 2.1 Signal model 9 2.2 Consideration of waveform 12 2.3 Image reconstruction algorithm 16 2.3.1 Back-projection algorithm 16 2.3.2 1D-MIMO range-migration algorithm 20 2.3.3 1D-MIMO range stacking algorithm 27 2.4 Sampling criteria and resolution 31 2.5 Simulation results 36 3 MIMO-FMCW RADAR IMPLEMENTATION WITH 16 TX - 16 RX ONE- DIMENSIONAL ARRAYS 46 3.1 Wide-band FMCW waveform generator architecture 46 3.2 Overall system architecture 48 3.3 Antenna and RF transceiver module 53 3.4 Wide-band FMCW waveform generator 55 3.5 FPGA-based digital hardware design 63 3.6 System integration and software design 71 3.7 Testing and measurement 75 3.7.1 Chirp waveform measurement 75 3.7.2 Range profile measurement 77 3.7.3 2-D imaging test 79 4 METHODS OF IMAGE QUALITY ENHANCEMENT 84 4.1 Signal model 84 4.2 Digital pre-distortion of chirp signal 86 4.2.1 Proposed DPD hardware system 86 4.2.2 Proposed DPD algorithm 88 4.2.3 Measurement results 90 4.3 Robust calibration method for signal distortion 97 4.3.1 Signal model 98 4.3.2 Problem formulation 99 4.3.3 Measurement results 105 5 THREE-DIMENSIONAL IMAGING USING 1-D ARRAY SYSTEM AND ISAR TECHNIQUE 110 5.1 Formulation for 1D-MIMO-ISAR RSA 111 5.2 Algorithm implementation 114 5.3 Simulation results 120 5.4 Experimental results 122 6 CONCLUSIONS AND FUTURE WORK 127 6.1 Conclusions 127 6.2 Future work 129 6.2.1 Effects of antenna polarization in the Ku-band 129 6.2.2 Forward-looking near-field ISAR configuration 130 6.2.3 Estimation of the movement errors in ISAR configuration 131 Abstract (In Korean) 145 Acknowlegement 148박

A fully integrated SRAM-based CMOS arbitrary waveform generator for analog signal processing

This dissertation focuses on design and implementation of a fully-integrated SRAM-based arbitrary waveform generator for analog signal processing applications in a CMOS technology. The dissertation consists of two parts: Firstly, a fully-integrated arbitrary waveform generator for a multi-resolution spectrum sensing of a cognitive radio applications, and an analog matched-filter for a radar application and secondly, low-power techniques for an arbitrary waveform generator. The fully-integrated low-power AWG is implemented and measured in a 0.18-¥ìm CMOS technology. Theoretical analysis is performed, and the perspective implementation issues are mentioned comparing the measurement results. Moreover, the low-power techniques of SRAM are addressed for the analog signal processing: Self-deactivated data-transition bit scheme, diode-connected low-swing signaling scheme with a short-current reduction buffer, and charge-recycling with a push-pull level converter for power reduction of asynchronous design. Especially, the robust latch-type sense amplifier using an adaptive-latch resistance and fully-gated ground 10T-SRAM bitcell in a 45-nm SOI technology would be used as a technique to overcome the challenges in the upcoming deep-submicron technologies.Ph.D.Committee Chair: Kim, Jongman; Committee Member: Kang, Sung Ha; Committee Member: Lee, Chang-Ho; Committee Member: Mukhopadhyay, Saibal; Committee Member: Tentzeris, Emmanouil

A LINEARIZATION METHOD FOR A UWB VCO-BASED CHIRP GENERATOR USING DUAL COMPENSATION

Ultra-Wideband (UWB) chirp generators are used on Frequency Modulated Continuous Wave (FMCW) radar systems for high-resolution and high-accuracy range measurements. At the Center for Remote Sensing of Ice Sheets (CReSIS), we have developed two UWB radar sensors for high resolution measurements of surface elevation and snow cover over Greenland and Antarctica. These radar systems are routinely operated from both surface and airborne platforms. Low cost implementations of UWB chirp generators are possible using an UWB Voltage Controlled Oscillator (VCO). VCOs possess several advantages over other competing technologies, but their frequency-voltage tuning characteristics are inherently non-linear. This nonlinear relationship between the tuning voltage and the output frequency should be corrected with a linearization system to implement a linear frequency modulated (LFM) waveform, also known as a chirp. If the waveform is not properly linearized, undesired additional frequency modulation is found in the waveform. This additional frequency modulation results in undesired sidebands at the frequency spectrum of the Intermediate Frequency (IF) stage of the FMCW radar. Since the spectrum of the filtered IF stage represents the measured range, the uncorrected nonlinear behavior of the VCO will cause a degradation of the range sensing performance of a FMCW radar. This issue is intensified as the chirp rate and nominal range of the target increase. A linearization method has been developed to linearize the output of a VCO-based chirp generator with 6 GHz of bandwidth. The linearization system is composed of a Phase Lock Loop (PLL) and an external compensation added to the loop. The nonlinear behavior of the VCO was treated as added disturbances to the loop, and a wide loop bandwidth PLL was designed for wideband compensation of these disturbances. Moreover, the PLL requires a loop filter able to attenuate the reference spurs. The PLL has been designed with a loop bandwidth as wide as possible while maintaining the reference spur level below 35 dBc. Several design considerations were made for the large loop bandwidth design. Furthermore, the large variations in the tuning sensitivity of the oscillator forced a design with a large phase margin at the average tuning sensitivity. This design constraint degraded the tracking performance of the PLL. A second compensation signal, externally generated, was added to the compensation signal of the PLL. By adding a compensation signal, which was not affected by the frequency response effects of the loop compensation, the loop tracking error is reduced. This technique enabled us to produce an output chirp signal that is a much closer replica of the scaled version of the reference signal. Furthermore, a type 1 PLL was chosen for improved transient response, compared to that of the type 2 PLL. This type of PLL requires an external compensation to obtain a finite steady state error when applying a frequency ramp to the input. The external compensation signal required to solve this issue was included in the second compensation signal mentioned above. Measurements for the PLL performance and the chirp generator performance were performed in the laboratory using a radar demonstrator. The experimental results show that the designed loop bandwidth was successfully achieved without significantly increasing the spurious signal level. The chirp generator measurements show a direct relationship between the bandwidth of the external compensation and the range resolution performance

Wideband harmonic radar detection

Radio sites consist naturally of metallic structures. Metals are always covered by an oxide film due to the metal reacting chemically with the oxygen in air. The rate of this oxide formation depends largely on the environment. Any oxide film between metallic contacts will cause non-linearity. RF currents passing through these junctions would generate harmonics. When RF signals at two frequencies fl and f2 pass-through a non-linearity they create signals at their sum and difference frequencies. These are known as 'inter-modulation products'. This generation of inter-modulation products when radio waves interact with rusty parts is called as the 'Rusty Bolt Effect'. Radio spectrum is carefully controlled for optimal usage of the available frequencies so that different services operate in well-defined frequency channels. Ofcom has set some standards for radio site engineering. This set of standards is given in the document 'MPT 1331: Code of Practice for Radio Site Engineering'. Any transmission site which is not following these codes would likely cause interference to other users. It is important that radio engineers should check the sites for their compliance with these codes. If a particular radio site is causing interference due to the rusty-bolt effect, the corroded points must be located to minimize their effect using a Harmonic Radar. A 'Harmonic Radar' is a device that illuminates a region of space with RF waves and receives the harmonics of the transmitted frequencies. The received data can then be processed to find the exact location and mobility of the points causing the generation of these harmonics. It works on the principle of radar transmitting a chirp signal and receiving harmonics of the transmitting frequency. Work is currently being carried out at the 'Centre for Communication Systems' in Durham University funded by HMGCC on the design and implementation of a novel Wideband Harmonic Radar system. The radar system would employ advanced sub-systems i.e. a suitable waveform and multiple antenna arrays processing super-resolution algorithms for angular information

Airborne UHF Radar for Fine Resolution Mapping of Near Surface Accumulation Layers in Greenland and West Antarctica

The usefulness of accurate, fine resolution accumulation layer measurements over central Greenland and West Antarctica is significant for the improvement of ice sheet models. These models are critical to both global climate models as well as understanding sea level rise. Previously developed accumulation layer radars were used as templates for the current single channel system. Improvements were incorporated including increased output power, increased receiver sensitivity, single antenna operation, and reduced susceptibility to external noise sources. Steps were also taken to reuse previously purchased components to reduce development costs. Externally developed Vivaldi and elliptical dipole antennas were utilized. Collected data shows the system is capable of measuring layering to a depth of nearly 300 m in most dry snow regions of Greenland and West Antarctica with a resolution of ~0.5 m. Future revisions will focus on reducing size and weight, as well as incorporate multiple receive channels to allow for clutter rejection algorithms to be applied; this will allow for viable data collection in percolation and wet snow zone of major ice sheets

Development and Implementation of a VHF High Power Amplifier for the Multi-Channel Coherent Radar Depth Sounder/Imager System

This thesis presents the implementation and characterization of a VHF high power amplifier developed for the Multi-channel Coherent Radar Depth Sounder/Imager (MCoRDS/I) system. MCoRDS/I is used to collect data on the thickness and basal topography of polar ice sheets, ice sheet margins, and fast-flowing glaciers from airborne platforms. Previous surveys have indicated that higher transmit power is needed to improve the performance of the radar, particularly when flying over challenging areas. The VHF high power amplifier system presented here consists of a 50-W driver amplifier and a 1-kW output stage operating in Class C. Its performance was characterized and optimized to obtain the best tradeoff between linearity, output power, efficiency, and conducted and radiated noise. A waveform pre-distortion technique to correct for gain variations (dependent on input power and operating frequency) was demonstrated using digital techniques. The amplifier system is a modular unit that can be expanded to handle a larger number of transmit channels as needed for future applications. The system can support sequential transmit/receive operations on a single antenna by using a high-power circulator and a duplexer circuit composed of two 90° hybrid couplers and anti-parallel diodes. The duplexer is advantageous over switches based on PIN-diodes due to the moderately high power handling capability and fast switching time. The system presented here is also smaller and lighter than previous implementations with comparable output power levels

Scattering Analysis and Ultra-Wideband Radar for High-Throughput Phenotyping of Wheat Canopies

Rising the yield of wheat crops is essential to meet the projected demands of future consumption and it is expected that most yield increases will be associated to improvements in biomass accumulation. Cultivars with canopy architectures that focus the light interception where photosynthetic-capacity is greater achieve larger biomass accumulation rates. Identifying varieties with improved traits could be performed with modern breeding methods, such as genomic-selection, which depend on genotype-phenotype mappings. Developing a non-destructive sensor with the capability of efficiently phenotyping wheat-canopy architecture parameters, such as height and vertical distribution of projected-leaf-area-density, would be useful for developing architecture-related genotype-phenotype maps of wheat cultivars. In this dissertation, new scattering analysis tools and a new 2-18 GHz radar system are presented for efficiently phenotyping the architecture of wheat canopies. The radar system presented was designed with the objective to measure the RCS profile of wheat canopies at close range. The frequency range (2-18 GHz), topology (Frequency-modulated-continuous-wave) and other radar parameters were chosen to meet that goal. Phase noise of self-interference signals is the main source of coherent and incoherent noise in FMCW radars. A new comprehensive noise analysis is presented, which predicts the power-spectral-density of the noise at the output of FMCW radars, including those related to phase noise. The new 2-18 GHz chirp generator is based on a phase-locked-loop that was designed with large loop bandwidth to suppress the phase noise of the chirp. Additionally, the radar RF front-end was designed to achieve low levels of LO-leakage and antenna feed-through, which are the main self-interference signals of FMCW radars. In addition to the radar system, a new efficient radar simulator was developed to predict the RCS waveforms collected from wheat canopies over the 2-18 GHz frequency range. The coherent radar simulator is based on novel geometric and fully-polarimetric scattering models of wheat canopies. The scattering models of wheat canopies, leaves with arbitrary orientation and curvature, stems and heads were validated using a full-wave commercial simulator and measurements. The radar simulator was used to derive retrieval algorithms of canopy height and projected-leaf-area-density from RCS profiles, which were tested with field-collected measurements. The retrieved heights and projected-leaf-area densities compare well against ruler measurements and image-based retrievals, respectively

Architectures and Algorithms for the Signal Processing of Advanced MIMO Radar Systems

This thesis focuses on the research, development and implementation of novel concepts, architectures, demonstrator systems and algorithms for the signal processing of advanced Multiple Input Multiple Output (MIMO) radar systems. The key concept is to address compact system, which have high resolutions and are able to perform a fast radar signal processing, three-dimensional (3D), and four-dimensional (4D) beamforming for radar image generation and target estimation. The idea is to obtain a complete sensing of range, Azimuth and elevation (additionally Doppler as the fourth dimension) from the targets in the radar captures. The radar technology investigated, aims at addressing sev- eral civil and military applications, such as surveillance and detection of targets, both air and ground based, and situational awareness, both in cars and in flying platforms, from helicopters, to Unmanned Aerial Vehicles (UAV) and air-taxis. Several major topics have been targeted. The development of complete systems and innovative FPGA, ARM and software based digital architectures for 3D imaging MIMO radars, which operate in both Time Division Multiplexing (TDM) and Frequency Divi- sion Multiplexing (FDM) modes, with Frequency Modulated Continuous Wave (FMCW) and Orthogonal Frequency Division Multiplexing (OFDM) signals, respectively. The de- velopment of real-time radar signal processing, beamforming and Direction-Of-Arrival (DOA) algorithms for target detection, with particular focus on FFT based, hardware implementable techniques. The study and implementation of advanced system concepts, parametrisation and simulation of next generation real-time digital radars (e.g. OFDM based). The design and development of novel constant envelope orthogonal waveforms for real-time 3D OFDM MIMO radar systems. The MIMO architectures presented in this thesis are a collection of system concepts, de- sign and simulations, as well as complete radar demonstrators systems, with indoor and outdoor measurements. Several of the results shown, come in the form of radar images which have been captured in field-test, in different scenarios, which aid in showing the proper functionality of the systems. The research activities for this thesis, have been carried out on the premises of Air- bus, based in Munich (Germany), as part of a Ph.D. candidate joint program between Airbus and the Polytechnic Department of Engineering and Architecture (Dipartimento Politecnico di Ingegneria e Architettura), of the University of Udine, based in Udine (Italy).Questa tesi si concentra sulla ricerca, lo sviluppo e l\u2019implementazione di nuovi concetti, architetture, sistemi dimostrativi e algoritmi per l\u2019elaborazione dei segnali in sistemi radar avanzati, basati su tecnologia Multiple Input Multiple Output (MIMO). Il con- cetto chiave `e quello di ottenere sistemi compatti, dalle elevate risoluzioni e in grado di eseguire un\u2019elaborazione del segnale radar veloce, un beam-forming tri-dimensionale (3D) e quadri-dimensionale (4D) per la generazione di immagini radar e la stima delle informazioni dei bersagli, detti target. L\u2019idea `e di ottenere una stima completa, che includa la distanza, l\u2019Azimuth e l\u2019elevazione (addizionalmente Doppler come quarta di- mensione) dai target nelle acquisizioni radar. La tecnologia radar indagata ha lo scopo di affrontare diverse applicazioni civili e militari, come la sorveglianza e la rilevazione di targets, sia a livello aereo che a terra, e la consapevolezza situazionale, sia nelle auto che nelle piattaforme di volo, dagli elicotteri, ai Unmanned Aerial Vehicels (UAV) e taxi volanti (air-taxis). Le tematiche affrontante sono molte. Lo sviluppo di sistemi completi e di architetture digitali innovative, basate su tecnologia FPGA, ARM e software, per radar 3D MIMO, che operano in modalit`a Multiplexing Time Division Multiplexing (TDM) e Multiplexing Frequency Diversion (FDM), con segnali di tipo FMCW (Frequency Modulated Contin- uous Wave) e Orthogonal Frequency Division Multiplexing (OFDM), rispettivamente. Lo sviluppo di tecniche di elaborazione del segnale radar in tempo reale, algoritmi di beam-forming e di stima della direzione di arrivo, Direction-Of-Arrival (DOA), dei seg- nali radar, per il rilevamento dei target, con particolare attenzione a processi basati su trasformate di Fourier (FFT). Lo studio e l\u2019implementazione di concetti di sistema avan- zati, parametrizzazione e simulazione di radar digitali di prossima generazione, capaci di operare in tempo reale (ad esempio basati su architetture OFDM). Progettazione e sviluppo di nuove forme d\u2019onda ortogonali ad inviluppo costante per sistemi radar 3D di tipo OFDM MIMO, operanti in tempo reale. Le attivit`a di ricerca di questa tesi sono state svolte presso la compagnia Airbus, con sede a Monaco di Baviera (Germania), nell\u2019ambito di un programma di dottorato, svoltosi in maniera congiunta tra Airbus ed il Dipartimento Politecnico di Ingegneria e Architettura dell\u2019Universit`a di Udine, con sede a Udine

Waveform generator for Software Defined Radio

Mestrado em Engenharia Eléctrónica e TelecomunicaçõesEsta dissertação insere-se na área de eletrónica de radio frequência, mais concretamente na geração de sinal para caracterizar sistemas com a arquitetura Software Denned Radio (SDR). Esta arquitetura tem como conceito a definição de um rádio completamente ajustável por software, através de conversão de blocos de domínio análgico para digital. Atendendo a importância que as novas tecnologias têm nos dias de hoje, os sistemas SDR aparecem como uma solução, uma vez que tendem a diminuir a parte de hardware, aproximando a conversão para o domínio digital cada vez mais próxima da antena. Neste trabalho propõem-se duas implementações, um gerador CW (Continuous Wave) que tem como funções estimular um dispositivo sobre teste e ainda de actuar como oscilador local. A outra implementação assemelhando-se com a arquitetura de um gerador AWG (Arbitrary Waveform Generator) que terá como função originar dois tons para estimular um dispositivo sobre teste. A gama de frequências encontra-se entre os 40 e 1000 MHz.This dissertation is inserted into the area of radio frequency electronics, specially in signal generation to characterize systems with Software Defined Radio (SDR) architecture. This architecture has like a concept defining a radio completely adjustable by software, by converting blocks of the analog domain to the digital domain. This architecture has like a concept defining a radio completely adjustable by software, by converting blocks of the analog domain to the digital domain. Considering the importance that new technologies have nowadays, SDR systems appear as a solution since they tend to reduce the hardware part by approximating the conversion to the digital domain closer and closer to the antenna. In this work, two implementations are proposed, one is a CW (Continuous Wave) generator which has the function to stimulate a device under test and also to act as a local oscillator. In the other implementation, that has a similar architecture of an AWG (Arbitrary Waveform Generator) generator has as function generating two tones to stimulate a device under test