4,648 research outputs found
Grasping bulky objects with two anthropomorphic hands
© 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other worksThis paper presents an algorithm to compute precision grasps for bulky objects using two anthropomorphic hands. We use objects modeled as point clouds obtained from a sensor camera or from a CAD model. We then process the point clouds dividing them into two set of slices where we look for sets of triplets of points. Each triplet must accomplish some physical conditions based on the structure of the hands. Then, the triplets of points from each set of slices are evaluated to find a combination that satisfies the force closure condition (FC). Once one valid couple of triplets have been found the inverse kinematics of the system is computed in order to know if the corresponding points are reachable by the hands, if so, motion planning and a collision check are performed to asses if the final grasp configuration of the system is suitable. The paper
inclu des some application examples of the proposed approachAccepted versio
From 3D Models to 3D Prints: an Overview of the Processing Pipeline
Due to the wide diffusion of 3D printing technologies, geometric algorithms
for Additive Manufacturing are being invented at an impressive speed. Each
single step, in particular along the Process Planning pipeline, can now count
on dozens of methods that prepare the 3D model for fabrication, while analysing
and optimizing geometry and machine instructions for various objectives. This
report provides a classification of this huge state of the art, and elicits the
relation between each single algorithm and a list of desirable objectives
during Process Planning. The objectives themselves are listed and discussed,
along with possible needs for tradeoffs. Additive Manufacturing technologies
are broadly categorized to explicitly relate classes of devices and supported
features. Finally, this report offers an analysis of the state of the art while
discussing open and challenging problems from both an academic and an
industrial perspective.Comment: European Union (EU); Horizon 2020; H2020-FoF-2015; RIA - Research and
Innovation action; Grant agreement N. 68044
Map-Based Localization for Unmanned Aerial Vehicle Navigation
Unmanned Aerial Vehicles (UAVs) require precise pose estimation when navigating in indoor and GNSS-denied / GNSS-degraded outdoor environments. The possibility of crashing in these environments is high, as spaces are confined, with many moving obstacles. There are many solutions for localization in GNSS-denied environments, and many different technologies are used. Common solutions involve setting up or using existing infrastructure, such as beacons, Wi-Fi, or surveyed targets. These solutions were avoided because the cost should be proportional to the number of users, not the coverage area. Heavy and expensive sensors, for example a high-end IMU, were also avoided. Given these requirements, a camera-based localization solution was selected for the sensor pose estimation. Several camera-based localization approaches were investigated. Map-based localization methods were shown to be the most efficient because they close loops using a pre-existing map, thus the amount of data and the amount of time spent collecting data are reduced as there is no need to re-observe the same areas multiple times. This dissertation proposes a solution to address the task of fully localizing a monocular camera onboard a UAV with respect to a known environment (i.e., it is assumed that a 3D model of the environment is available) for the purpose of navigation for UAVs in structured environments.
Incremental map-based localization involves tracking a map through an image sequence. When the map is a 3D model, this task is referred to as model-based tracking. A by-product of the tracker is the relative 3D pose (position and orientation) between the camera and the object being tracked. State-of-the-art solutions advocate that tracking geometry is more robust than tracking image texture because edges are more invariant to changes in object appearance and lighting. However, model-based trackers have been limited to tracking small simple objects in small environments. An assessment was performed in tracking larger, more complex building models, in larger environments. A state-of-the art model-based tracker called ViSP (Visual Servoing Platform) was applied in tracking outdoor and indoor buildings using a UAVs low-cost camera. The assessment revealed weaknesses at large scales. Specifically, ViSP failed when tracking was lost, and needed to be manually re-initialized. Failure occurred when there was a lack of model features in the cameras field of view, and because of rapid camera motion. Experiments revealed that ViSP achieved positional accuracies similar to single point positioning solutions obtained from single-frequency (L1) GPS observations standard deviations around 10 metres. These errors were considered to be large, considering the geometric accuracy of the 3D model used in the experiments was 10 to 40 cm. The first contribution of this dissertation proposes to increase the performance of the localization system by combining ViSP with map-building incremental localization, also referred to as simultaneous localization and mapping (SLAM). Experimental results in both indoor and outdoor environments show sub-metre positional accuracies were achieved, while reducing the number of tracking losses throughout the image sequence. It is shown that by integrating model-based tracking with SLAM, not only does SLAM improve model tracking performance, but the model-based tracker alleviates the computational expense of SLAMs loop closing procedure to improve runtime performance. Experiments also revealed that ViSP was unable to handle occlusions when a complete 3D building model was used, resulting in large errors in its pose estimates. The second contribution of this dissertation is a novel map-based incremental localization algorithm that improves tracking performance, and increases pose estimation accuracies from ViSP. The novelty of this algorithm is the implementation of an efficient matching process that identifies corresponding linear features from the UAVs RGB image data and a large, complex, and untextured 3D model. The proposed model-based tracker improved positional accuracies from 10 m (obtained with ViSP) to 46 cm in outdoor environments, and improved from an unattainable result using VISP to 2 cm positional accuracies in large indoor environments.
The main disadvantage of any incremental algorithm is that it requires the camera pose of the first frame. Initialization is often a manual process. The third contribution of this dissertation is a map-based absolute localization algorithm that automatically estimates the camera pose when no prior pose information is available. The method benefits from vertical line matching to accomplish a registration procedure of the reference model views with a set of initial input images via geometric hashing. Results demonstrate that sub-metre positional accuracies were achieved and a proposed enhancement of conventional geometric hashing produced more correct matches - 75% of the correct matches were identified, compared to 11%. Further the number of incorrect matches was reduced by 80%
Continuous close-range 3D object pose estimation
In the context of future manufacturing lines, removing fixtures will be a
fundamental step to increase the flexibility of autonomous systems in assembly
and logistic operations. Vision-based 3D pose estimation is a necessity to
accurately handle objects that might not be placed at fixed positions during
the robot task execution. Industrial tasks bring multiple challenges for the
robust pose estimation of objects such as difficult object properties, tight
cycle times and constraints on camera views. In particular, when interacting
with objects, we have to work with close-range partial views of objects that
pose a new challenge for typical view-based pose estimation methods. In this
paper, we present a 3D pose estimation method based on a gradient-ascend
particle filter that integrates new observations on-the-fly to improve the pose
estimate. Thereby, we can apply this method online during task execution to
save valuable cycle time. In contrast to other view-based pose estimation
methods, we model potential views in full 6- dimensional space that allows us
to cope with close-range partial objects views. We demonstrate the approach on
a real assembly task, in which the algorithm usually converges to the correct
pose within 10-15 iterations with an average accuracy of less than 8mm
- …