3,024 research outputs found
Stability and Transient Performance Assessment in a COTS-Module-Based Distributed DC/DC System
This paper introduces a method to analyze and predict stability and transient performance of a distributed system where COTS (Commercial-off-the-shelf) modules share an input filter. The presented procedure is based on the measured data from the input and output terminals of the power modules. The required information for the analysis is obtained by performing frequency response measurements for each converter. This attained data is utilized to compute special transfer functions, which partly determine the source and load interactions within the converters. The system level dynamic description is constructed based on the measured and computed transfer functions introducing cross-coupling mechanisms within the system. System stability can be studied based on the well-known impedance- related minor-loop gain at an arbitrary interface within the system
Modeling and Nonlinear Control of dc–dc Converters for Microgrid Applications
This paper proposes a high-performance control strategy for dc–dc converters supplying combined loads (constant current/power, and/or linear loads). This strategy combines a feedback law with a feedforward compensation. The feedback law is based on full feedback linearization, which guarantees that zero dynamics are avoided. To design a single controller for the three basic converter topologies (i.e., buck, boost and buck–boost), a unified model for these converters is introduced. From the resulting combined control law, the specific control law for each type of converter can be obtained by setting three constant coefficient to 0 or 1. The feedforward compensation is based on the estimated values of the load obtained via a nonlinear observer. The main advantage of this unified approach is that it is implemented by using a single algorithm which can be executed in a dedicated hardware, for instance, a single integrated circuit, providing a unified solution for the control of the mentioned topologies. The good performance of the proposed scheme is verified through simulations and tested via experimental application cases, concluding that this is a good unified solution to control dc–dc converters used in microgrid applications.Fil: Solsona, Jorge Alberto. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Bahía Blanca. Instituto de Investigaciones en Ingeniería Eléctrica "Alfredo Desages". Universidad Nacional del Sur. Departamento de Ingeniería Eléctrica y de Computadoras. Instituto de Investigaciones en Ingeniería Eléctrica "Alfredo Desages"; ArgentinaFil: Gómez Jorge, Sebastián. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Bahía Blanca. Instituto de Investigaciones en Ingeniería Eléctrica "Alfredo Desages". Universidad Nacional del Sur. Departamento de Ingeniería Eléctrica y de Computadoras. Instituto de Investigaciones en Ingeniería Eléctrica "Alfredo Desages"; ArgentinaFil: Busada, Claudio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Bahía Blanca. Instituto de Investigaciones en Ingeniería Eléctrica "Alfredo Desages". Universidad Nacional del Sur. Departamento de Ingeniería Eléctrica y de Computadoras. Instituto de Investigaciones en Ingeniería Eléctrica "Alfredo Desages"; Argentin
Addressing Instability Issues in Microgrids Caused By Constant Power Loads Using Energy Storage Systems
Renewable energy sources, the most reasonable fuel-shift taken over the naturally limited conventional fuels, necessarily deal with the self-functional microgrid system rather than the traditional grid distribution system. The study shows that the microgrid system, a comparatively low-powered system, experiences the challenge of instability due to the constant power load (CPL) from many electronic devices such as inverter-based systems. In this dissertation, as a methodical approach to mitigate the instability complication, AC microgrid stability is thoroughly investigated for each and every considerable parameter of the system. Furthermore, a specific loading limit is depicted by evaluating the stability margin from the small signal analysis of the microgrid scheme. After demonstrating all cases regarding the instability problem, the storage-based virtual impedance power compensation method is introduced to restore the system stability and literally extend the loading limit of the microgrid system. Here, a PID controller is implemented to maintain the constant terminal voltage of CPL via current injection method from storage. Since the system is highly nonlinear by nature, advanced nonlinear control techniques, such as Sliding Mode Control and Lyapunov Redesign Control technique, are implemented to control the entire nonlinear system. Robustness, noise rejection, and frequency variation are scrutinized rigorously in a virtual platform such as Matlab/Simulink with appreciable aftermaths. After that, a comparative analysis is presented between SMC and LRC controller robustness by varying CPL power. From this analysis, it is evident that Lyapunov redesign controller performs better than the previous one in retaining microgrid stability for dense CPL-loaded conditions. Finally, to ensure a robust storage system, Hybrid Energy Storage System is introduced and its advantages are discussed as extended research work
Recommended from our members
Hierarchical control of dc microgrids with constant power loads
This dissertation proposes general methodologies for designing hierarchical control schemes for dc microgrids loaded by constant power loads (CPLs). CPLs form a major proportion of the system loads in many microgrids. Without proper control, CPLs present destabilizing effect at the dc microgrid. In addition to stable operation of microgrid, proper current sharing among paralleled sources is essential. The proposed hierarchical control strategy consists of two control levels. The lower level consists of droop-based primary controllers which enables current-sharing among paralleled sources and also damps limit cycle oscillations due to CPLs. The higher level consists of secondary controller which compensates for voltage deviations due to primary controller. This higher level is implemented either as autonomous controllers or as a centralized controller. In the case of autonomous secondary controllers, they operate alongside of primary controllers in each of the paralleled converters. In the case of centralized secondary controller, a remote secondary controller uses a high speed communication link to communicate to local controllers.
Interfacing sources with different characteristics and voltage ranges necessitates the use of complex converter topologies. As an initial step towards implementing hierarchical control scheme for such microgrids with CPLs, a linear controller is proposed for dc microgrids with standalone SEPIC, Cuk and Zeta converters. During the first stage of the two stage controller, limit cycle oscillations are damped by inserting a virtual resistance in series with the converter input inductor. During the second stage, an integral controller is added to the first stage to compensate for voltage deviations. For microgrids containing different converter topologies, stability of equilibrium points is examined and stability conditions are derived and explained. Experiments performed on a prototype microgrid are used to verify the proposed control laws.
Expanding study on stability of microgrids, the maximum real power load in a dc microgrid bus is traced geometrically. The generalized circle diagram approach used in a conventional power system is modified for this purpose. The different types of buses present in a dc microgrid are described and the locus of operating points is obtained. The proposed method is verified by simulations on an example dc microgrid.Electrical and Computer Engineerin
- …