Design and Validation of Network-on-Chip Architectures for the Next Generation of Multi-synchronous, Reliable, and Reconfigurable Embedded Systems

NETWORK-ON-CHIP (NoC) design is today at a crossroad. On one hand, the design principles to efficiently implement interconnection networks in the resource-constrained on-chip setting have stabilized. On the other hand, the requirements on embedded system design are far from stabilizing. Embedded systems are composed by assembling together heterogeneous components featuring differentiated operating speeds and ad-hoc counter measures must be adopted to bridge frequency domains. Moreover, an unmistakable trend toward enhanced reconfigurability is clearly underway due to the increasing complexity of applications. At the same time, the technology effect is manyfold since it provides unprecedented levels of system integration but it also brings new severe constraints to the forefront: power budget restrictions, overheating concerns, circuit delay and power variability, permanent fault, increased probability of transient faults. Supporting different degrees of reconfigurability and flexibility in the parallel hardware platform cannot be however achieved with the incremental evolution of current design techniques, but requires a disruptive approach and a major increase in complexity. In addition, new reliability challenges cannot be solved by using traditional fault tolerance techniques alone but the reliability approach must be also part of the overall reconfiguration methodology. In this thesis we take on the challenge of engineering a NoC architectures for the next generation systems and we provide design methods able to overcome the conventional way of implementing multi-synchronous, reliable and reconfigurable NoC. Our analysis is not only limited to research novel approaches to the specific challenges of the NoC architecture but we also co-design the solutions in a single integrated framework. Interdependencies between different NoC features are detected ahead of time and we finally avoid the engineering of highly optimized solutions to specific problems that however coexist inefficiently together in the final NoC architecture. To conclude, a silicon implementation by means of a testchip tape-out and a prototype on a FPGA board validate the feasibility and effectivenes

Methodologies and Toolflows for the Predictable Design of Reliable and Low-Power NoCs

There is today the unmistakable need to evolve design methodologies and tool ows for Network-on-Chip based embedded systems. In particular, the quest for low-power requirements is nowadays a more-than-ever urgent dilemma. Modern circuits feature billion of transistors, and neither power management techniques nor batteries capacity are able to endure the increasingly higher integration capability of digital devices. Besides, power concerns come together with modern nanoscale silicon technology design issues. On one hand, system failure rates are expected to increase exponentially at every technology node when integrated circuit wear-out failure mechanisms are not compensated for. However, error detection and/or correction mechanisms have a non-negligible impact on the network power. On the other hand, to meet the stringent time-to-market deadlines, the design cycle of such a distributed and heterogeneous architecture must not be prolonged by unnecessary design iterations. Overall, there is a clear need to better discriminate reliability strategies and interconnect topology solutions upfront, by ranking designs based on power metric. In this thesis, we tackle this challenge by proposing power-aware design technologies. Finally, we take into account the most aggressive and disruptive methodology for embedded systems with ultra-low power constraints, by migrating NoC basic building blocks to asynchronous (or clockless) design style. We deal with this challenge delivering a standard cell design methodology and mainstream CAD tool ows, in this way partially relaxing the requirement of using asynchronous blocks only as hard macros

Design of variation-tolerant synchronizers for multiple clock and voltage domains

PhD ThesisParametric variability increasingly affects the performance of electronic circuits as the fabrication technology has reached the level of 32nm and beyond. These parameters may include transistor Process parameters (such as threshold voltage), supply Voltage and Temperature (PVT), all of which could have a significant impact on the speed and power consumption of the circuit, particularly if the variations exceed the design margins. As systems are designed with more asynchronous protocols, there is a need for highly robust synchronizers and arbiters. These components are often used as interfaces between communication links of different timing domains as well as sampling devices for asynchronous inputs coming from external components. These applications have created a need for new robust designs of synchronizers and arbiters that can tolerate process, voltage and temperature variations. The aim of this study was to investigate how synchronizers and arbiters should be designed to tolerate parametric variations. All investigations focused mainly on circuit-level and transistor level designs and were modeled and simulated in the UMC90nm CMOS technology process. Analog simulations were used to measure timing parameters and power consumption along with a “Monte Carlo” statistical analysis to account for process variations. Two main components of synchronizers and arbiters were primarily investigated: flip-flop and mutual-exclusion element (MUTEX). Both components can violate the input timing conditions, setup and hold window times, which could cause metastability inside their bistable elements and possibly end in failures. The mean-time between failures is an important reliability feature of any synchronizer delay through the synchronizer. The MUTEX study focused on the classical circuit, in addition to a number of tolerance, based on increasing internal gain by adding current sources, reducing the capacitive loading, boosting the transconductance of the latch, compensating the existing Miller capacitance, and adding asymmetry to maneuver the metastable point. The results showed that some circuits had little or almost no improvements, while five techniques showed significant improvements by reducing τ and maintaining high tolerance. Three design approaches are proposed to provide variation-tolerant synchronizers. wagging synchronizer proposed to First, the is significantly increase reliability over that of the conventional two flip-flop synchronizer. The robustness of the wagging technique can be enhanced by using robust τ latches or adding one more cycle of synchronization. The second approach is the Metastability Auto-Detection and Correction (MADAC) latch which relies on swiftly detecting a metastable event and correcting it by enforcing the previously stored logic value. This technique significantly reduces the resolution time down from uncertain synchronization technique is proposed to transfer signals between Multiple- Voltage Multiple-Clock Domains (MVD/MCD) that do not require conventional level-shifters between the domains or multiple power supplies within each domain. This interface circuit uses a synchronous set and feedback reset protocol which provides level-shifting and synchronization of all signals between the domains, from a wide range of voltage-supplies and clock frequencies. Overall, synchronizer circuits can tolerate variations to a greater extent by employing the wagging technique or using a MADAC latch, while MUTEX tolerance can suffice with small circuit modifications. Communication between MVD/MCD can be achieved by an asynchronous handshake without a need for adding level-shifters.The Saudi Arabian Embassy in London, Umm Al-Qura University, Saudi Arabi

CROSS-LAYER DESIGN, OPTIMIZATION AND PROTOTYPING OF NoCs FOR THE NEXT GENERATION OF HOMOGENEOUS MANY-CORE SYSTEMS

This thesis provides a whole set of design methods to enable and manage the runtime heterogeneity of features-rich industry-ready Tile-Based Networkon- Chips at different abstraction layers (Architecture Design, Network Assembling, Testing of NoC, Runtime Operation). The key idea is to maintain the functionalities of the original layers, and to improve the performance of architectures by allowing, joint optimization and layer coordinations. In general purpose systems, we address the microarchitectural challenges by codesigning and co-optimizing feature-rich architectures. In application-specific NoCs, we emphasize the event notification, so that the platform is continuously under control. At the network assembly level, this thesis proposes a Hold Time Robustness technique, to tackle the hold time issue in synchronous NoCs. At the network architectural level, the choice of a suitable synchronization paradigm requires a boost of synthesis flow as well as the coexistence with the DVFS. On one hand this implies the coexistence of mesochronous synchronizers in the network with dual-clock FIFOs at network boundaries. On the other hand, dual-clock FIFOs may be placed across inter-switch links hence removing the need for mesochronous synchronizers. This thesis will study the implications of the above approaches both on the design flow and on the performance and power quality metrics of the network. Once the manycore system is composed together, the issue of testing it arises. This thesis takes on this challenge and engineers various testing infrastructures. At the upper abstraction layer, the thesis addresses the issue of managing the fully operational system and proposes a congestion management technique named HACS. Moreover, some of the ideas of this thesis will undergo an FPGA prototyping. Finally, we provide some features for emerging technology by characterizing the power consumption of Optical NoC Interfaces

Design and performance optimization of asynchronous networks-on-chip

As digital systems continue to grow in complexity, the design of conventional synchronous systems is facing unprecedented challenges. The number of transistors on individual chips is already in the multi-billion range, and a greatly increasing number of components are being integrated onto a single chip. As a consequence, modern digital designs are under strong time-to-market pressure, and there is a critical need for composable design approaches for large complex systems. In the past two decades, networks-on-chip (NoC’s) have been a highly active research area. In a NoC-based system, functional blocks are first designed individually and may run at different clock rates. These modules are then connected through a structured network for on-chip global communication. However, due to the rigidity of centrally-clocked NoC’s, there have been bottlenecks of system scalability, energy and performance, which cannot be easily solved with synchronous approaches. As a result, there has been significant recent interest in combing the notion of asynchrony with NoC designs. Since the NoC approach inherently separates the communication infrastructure, and its timing, from computational elements, it is a natural match for an asynchronous paradigm. Asynchronous NoC’s, therefore, enable a modular and extensible system composition for an ‘object-orient’ design style. The thesis aims to significantly advance the state-of-art and viability of asynchronous and globally-asynchronous locally-synchronous (GALS) networks-on-chip, to enable high-performance and low-energy systems. The proposed asynchronous NoC’s are nearly entirely based on standard cells, which eases their integration into industrial design flows. The contributions are instantiated in three different directions. First, practical acceleration techniques are proposed for optimizing the system latency, in order to break through the latency bottleneck in the memory interfaces of many on-chip parallel processors. Novel asynchronous network protocols are proposed, along with concrete NoC designs. A new concept, called ‘monitoring network’, is introduced. Monitoring networks are lightweight shadow networks used for fast-forwarding anticipated traffic information, ahead of the actual packet traffic. The routers are therefore allowed to initiate and perform arbitration and channel allocation in advance. The technique is successfully applied to two topologies which belong to two different categories – a variant mesh-of-trees (MoT) structure and a 2D-mesh topology. Considerable and stable latency improvements are observed across a wide range of traffic patterns, along with moderate throughput gains. Second, for the first time, a high-performance and low-power asynchronous NoC router is compared directly to a leading commercial synchronous counterpart in an advanced industrial technology. The asynchronous router design shows significant performance improvements, as well as area and power savings. The proposed asynchronous router integrates several advanced techniques, including a low-latency circular FIFO for buffer design, and a novel end-to-end credit-based virtual channel (VC) flow control. In addition, a semi-automated design flow is created, which uses portions of a standard synchronous tool flow. Finally, a high-performance multi-resource asynchronous arbiter design is developed. This small but important component can be directly used in existing asynchronous NoC’s for performance optimization. In addition, this standalone design promises use in opening up new NoC directions, as well as for general use in parallel systems. In the proposed arbiter design, the allocation of a resource to a client is divided into several steps. Multiple successive client-resource pairs can be selected rapidly in pipelined sequence, and the completion of the assignments can overlap in parallel. In sum, the thesis provides a set of advanced design solutions for performance optimization of asynchronous and GALS networks-on-chip. These solutions are at different levels, from network protocols, down to router- and component-level optimizations, which can be directly applied to existing basic asynchronous NoC designs to provide a leap in performance improvement

Cross-Layer Optimization for Power-Efficient and Robust Digital Circuits and Systems

With the increasing digital services demand, performance and power-efficiency become vital requirements for digital circuits and systems. However, the enabling CMOS technology scaling has been facing significant challenges of device uncertainties, such as process, voltage, and temperature variations. To ensure system reliability, worst-case corner assumptions are usually made in each design level. However, the over-pessimistic worst-case margin leads to unnecessary power waste and performance loss as high as 2.2x. Since optimizations are traditionally confined to each specific level, those safe margins can hardly be properly exploited. To tackle the challenge, it is therefore advised in this Ph.D. thesis to perform a cross-layer optimization for digital signal processing circuits and systems, to achieve a global balance of power consumption and output quality. To conclude, the traditional over-pessimistic worst-case approach leads to huge power waste. In contrast, the adaptive voltage scaling approach saves power (25% for the CORDIC application) by providing a just-needed supply voltage. The power saving is maximized (46% for CORDIC) when a more aggressive voltage over-scaling scheme is applied. These sparsely occurred circuit errors produced by aggressive voltage over-scaling are mitigated by higher level error resilient designs. For functions like FFT and CORDIC, smart error mitigation schemes were proposed to enhance reliability (soft-errors and timing-errors, respectively). Applications like Massive MIMO systems are robust against lower level errors, thanks to the intrinsically redundant antennas. This property makes it applicable to embrace digital hardware that trades quality for power savings.Comment: 190 page

Fault Tolerant Task Mapping in Many-Core Systems

The advent of many-core systems, a network on chip containing hundreds or thousands of homogeneous processors cores, present new challenges in managing the cores effectively in response to processing demands, hardware faults and the need for heat management. Continually diminishing feature size of devices increase the probability of fabrication de- fects and the variability of performance of individual transistors. In many-core systems this can result in the failure of individual processing cores, routing nodes or communication links, which require the use of fault tolerant mechanisms. Diminishing feature size also increases the power density of devices, giving rise to the concept of dark silicon where only a portion of the functionality available on a chip can be active at any one time. Core fault tolerance and management of dark silicon can both be achieved by allocating a percentage of cores to be idle at any one time. Idle cores can be used as dark silicon to evenly distribute heat generated by processing cores and can also be used as spare cores to implement fault tolerance. Both of these can be achieved by the dynamic allocation of processes to tasks in response to changes to the status of hardware resources and the demands placed on the system, which in turn requires real time task mapping. This research proposes the use of a continuous fault/recovery cycle to implement graceful degradation and amelioration to provide real-time fault tolerance. Objective measures for core fault tolerance, link fault tolerance, network power and excess traffic have been developed for use by a multi-objective evolutionary algorithm that uses knowledge of the processing demands and hardware status to identify optimal task mappings. The fault/recovery cycle is shown to be effective in maintaining a high level of performance of a many-core array when presented with a series of hardware faults

Contributions to the fault tolerance of soft-core processors implemented in SRAM-based FPGA Systems.

239 p.Gracias al desarrollo de las tecnologías de diseño y fabricación, los circuitos electrónicos han llegado a grandes niveles de integración. De esta forma, hoy en día es posible implementar completos y complejos sistemas dentro de un único dispositivo incorporando gran variedad de elementos como: procesadores, osciladores, lazos de seguimiento de fase (PLLs), interfaces, conversores ADC y DAC, módulos de memoria, etc. A este concepto de diseño se le denomina comúnmente SoC (System-on-Chip). Una de las plataformas para implementar estos sistemas que más importancia está cobrando son las FPGAs (Field Programmable Gate Array). Históricamente la plataforma más utilizada para albergar los SoCs han sido las ASICs (Application- Specific Integrated Circuits), debido a su bajo consumo energético y su gran rendimiento. No obstante, su costoso proceso de desarrollo y fabricación hace que solo sean rentables en el caso de producciones masivas. Las FPGAs, por el contrario, al ser dispositivos configurables ofrecen, la posibilidad de implementar diseños personalizados a un coste mucho más reducido. Por otro lado, los continuos avances en la tecnología de las FPGAs están haciendo que éstas compitan con las ASICs a nivel de prestaciones (consumo, nivel de integración y eficiencia). Ciertas tecnologías de FPGA, como las SRAM y Flash, poseen una característica que las hace especialmente interesantes en multitud de diseños: la capacidad de reconfiguración. Dicha característica, que incluso puede ser realizada de forma autónoma, permite cambiar completamente el diseño hardware implementado con solo cargar en la FPGA un archivo de configuración denominado bitstream. La reconfiguración puede incluso permitir modificar una parte del circuito configurado en la matriz de la FPGA, mientras el resto del circuito implementado continua inalterado. Esto que se conoce como reconfiguración parcial dinámica, posibilita que un mismo chip albergue en su interior numerosos diseños hardware que pueden ser cargados a demanda. Gracias a la capacidad de reconfiguración, las FPGAs ofrecen numerosas ventajas como: posibilidad de personalización de diseños, capacidad de readaptación durante el funcionamiento para responder a cambios o corregir errores, mitigación de obsolescencia, diferenciación, menores costes de diseño o reducido tiempo para el lanzamiento de productos al mercado. Los SoC basados en FPGAs allanan el camino hacia un nuevo concepto de integración de hardware y software, permitiendo que los diseñadores de sistemas electrónicos sean capaces de integrar procesadores embebidos en los diseños para beneficiarse de su gran capacidad de computación. Gracias a esto, una parte importante de la electrónica hace uso de la tecnología FPGA abarcando un gran abanico de campos, como por ejemplo: la electrónica de consumo y el entretenimiento, la medicina o industrias como la espacial, la aviónica, la automovilística o la militar. Las tecnologías de FPGA existentes ofrecen dos vías de utilización de procesado- res embebidos: procesadores hardcore y procesadores softcore. Los hardcore son procesadores discretos integrados en el mismo chip de la FPGA. Generalmente ofrecen altas frecuencias de trabajo y una mayor previsibilidad en términos de rendimiento y uso del área, pero su diseño hardware no puede alterarse para ser personalizado. Por otro lado, un procesador soft-core, es la descripción hardware en lenguaje HDL (normalmente VDHL o Verilog) de un procesador, sintetizable e implementable en una FPGA. Habitualmente, los procesadores softcore suelen basarse en diseños hardware ya existentes, siendo compatibles con sus juegos de instrucciones, muchos de ellos en forma de IP cores (Intellectual Property co- res). Los IP cores ofrecen procesadores softcore prediseñados y testeados, que dependiendo del caso pueden ser de pago, gratuitos u otro tipo de licencias. Debido a su naturaleza, los procesadores softcore, pueden ser personalizados para una adaptación óptima a diseños específicos. Así mismo, ofrecen la posibilidad de integrar en el diseño tantos procesadores como se desee (siempre que haya disponibles recursos lógicos suficientes). Otra ventaja importante es que, gracias a la reconfiguración parcial dinámica, es posible añadir el procesador al diseño únicamente en los casos necesarios, ahorrando de esta forma, recursos lógicos y consumo energético. Uno de los mayores problemas que surgen al usar dispositivos basados en las tecnologías SRAM o la flash, como es el caso de las FPGAs, es que son especialmente sensibles a los efectos producidos por partículas energéticas provenientes de la radiación cósmica (como protones, neutrones, partículas alfa u otros iones pesados) denominados efectos de eventos simples o SEEs (Single Event Effects). Estos efectos pueden ocasionar diferentes tipos de fallos en los sistemas: desde fallos despreciables hasta fallos realmente graves que comprometan la funcionalidad del sistema. El correcto funcionamiento de los sistemas cobra especial relevancia cuando se trata de tecnologías de elevado costo o aquellas en las que peligran vidas humanas, como, por ejemplo, en campos tales como el transporte ferroviario, la automoción, la aviónica o la industria aeroespacial. Dependiendo de distintos factores, los SEEs pueden causar fallos de operación transitorios, cambios de estados lógicos o daños permanentes en el dispositivo. Cuando se trata de un fallo físico permanente se denomina hard-error, mientras que cuando el fallo afecta el circuito momentáneamente se denomina soft-error. Los SEEs más frecuentes son los soft-errors y afectan tanto a aplicaciones comerciales a nivel terrestre, como a aplicaciones aeronáuticas y aeroespaciales (con mayor incidencia en estas últimas). La contribución exacta de este tipo de fallos a la tasa de errores depende del diseño específico de cada circuito, pero en general se asume que entorno al 90 % de la tasa de error se debe a fallos en elementos de memoria (latches, biestables o celdas de memoria). Los soft-errors pueden afectar tanto al circuito lógico como al bitstream cargado en la memoria de configuración de la FPGA. Debido a su gran tamaño, la memoria de configuración tiene más probabilidades de ser afectada por un SEE. La existencia de problemas generados por estos efectos reafirma la importancia del concepto de tolerancia a fallos. La tolerancia a fallos es una propiedad relativa a los sistemas digitales, por la cual se asegura cierta calidad en el funcionamiento ante la presencia de fallos, debiendo los sistemas poder soportar los efectos de dichos fallos y funcionar correctamente en todo momento. Por tanto, para lograr un diseño robusto, es necesario garantizar la funcionalidad de los circuitos y asegurar la seguridad y confiabilidad en las aplicaciones críticas que puedan verse comprometidos por los SEE. A la hora de hacer frente a los SEE existe la posibilidad de explotar tecnologías específicas centradas en la tolerancia a fallos, como por ejemplo las FPGAs de tipo fusible, o, por otro lado, utilizar la tecnología comercial combinada con técnicas de tolerancia a fallos. Esta última opción va cobrando importancia debido al menor precio y mayores prestaciones de las FPGAs comerciales. Generalmente las técnicas de endurecimiento se aplican durante la fase de diseño. Existe un gran número de técnicas y se pueden llegar a combinar entre sí. Las técnicas prevalentes se basan en emplear algún tipo de redundancia, ya sea hardware, software, temporal o de información. Cada tipo de técnica presenta diferentes ventajas e inconvenientes y se centra en atacar distintos tipos de SEE y sus efectos. Dentro de las técnicas de tipo redundancia, la más utilizada es la hardware, que se basa en replicar el modulo a endurecer. De esta forma, cada una de las réplicas es alimentada con la misma entrada y sus salidas son comparadas para detectar discrepancias. Esta redundancia puede implementarse a diferentes niveles. En términos generales, un mayor nivel de redundancia hardware implica una mayor robustez, pero también incrementa el uso de recursos. Este incremento en el uso de recursos de una FPGA supone tener menos recursos disponibles para el diseño, mayor consumo energético, el tener más elementos susceptibles de ser afectados por un SEE y generalmente, una reducción de la máxima frecuencia alcanzable por el diseño. Por ello, los niveles de redundancia hardware más utilizados son la doble, conocida como DMR (Dual Modular Redundancy) y la triple o TMR (Triple Modular Redundancy). La DMR minimiza el número de recursos redundantes, pero presenta el problema de no poder identificar el módulo fallido ya que solo es capaz de detectar que se ha producido un error. Ello hace necesario combinarlo con técnicas adicionales. Al caso de DMR aplicado a procesadores se le denomina lockstep y se suele combinar con las técnicas checkpoint y rollback recovery. El checkpoint consiste en guardar periódicamente el contexto (contenido de registros y memorias) de instantes identificados como correctos. Gracias a esto, una vez detectado y reparado un fallo es posible emplear el rollback recovery para cargar el último contexto correcto guardado. Las desventajas de estas estrategias son el tiempo requerido por ambas técnicas (checkpoint y rollback recovery) y la necesidad de elementos adicionales (como memorias auxiliares para guardar el contexto). Por otro lado, el TMR ofrece la posibilidad de detectar el módulo fallido mediante la votación por mayoría. Es decir, si tras comparar las tres salidas una de ellas presenta un estado distinto, se asume que las otras dos son correctas. Esto permite que el sistema continúe funcionando correctamente (como sistema DMR) aun cuando uno de los módulos quede inutilizado. En todo caso, el TMR solo enmascara los errores, es decir, no los corrige. Una de las desventajas más destacables de esta técnica es que incrementa el uso de recursos en más de un 300 %. También cabe la posibilidad de que la salida discrepante sea la realmente correcta (y que, por tanto, las otras dos sean incorrectas), aunque este caso es bastante improbable. Uno de los problemas que no se ha analizado con profundidad en la bibliografía es el problema de la sincronización de procesadores soft-core en sistemas TMR (o de mayor nivel de redundancia). Dicho problema reside en que, si tras un fallo se inutiliza uno de los procesadores y el sistema continúa funcionando con el resto de procesadores, una vez reparado el procesador fallido éste necesita sincronizar su contexto al nuevo estado del sistema. Una práctica bastante común en la implementación de sistemas redundantes es combinarlos con la técnica conocida como scrubbing. Esta técnica basada en la reconfiguración parcial dinámica, consiste en sobrescribir periódicamente el bitstream con una copia libre de errores apropiadamente guardada. Gracias a ella, es posible corregir los errores enmascarados por el uso de algunas técnicas de endurecimiento como la redundancia hardware. Esta copia libre de errores suele omitir los bits del bitstream correspondientes a la memoria de usuario, por lo que solo actualiza los bits relacionados con la configuración de la FPGA. Por ello, a esta técnica también se la conoce como configuration scrubbing. En toda la literatura consultada se ha detectado un vacío en cuanto a técnicas que propongan estrategias de scrubbing para la memoria de usuario. Con el objetivo de proponer alternativas innovadoras en el terreno de la tolerancia a fallos para procesadores softcore, en este trabajo de investigación se han desarrollado varias técnicas y flujos de diseño para manejar los datos de usuario a través del bitstream, pudiendo leer, escribir o copiar la información de registros o de memorias implementadas en bloques RAMs de forma autónoma. Así mismo se ha desarrollado un abanico de propuestas tanto como para estrategias lockstep como para la sincronización de sistemas TMR, de las cuales varias hacen uso de las técnicas desarrolladas para manejar las memorias de usuario a través del bitstream. Estas últimas técnicas tienen en común la minimización de utilización de recursos respecto a las estrategias tradicionales. De forma similar, se proponen dos alternativas adicionales basadas en dichas técnicas: una propuesta de scrubbing para las memorias de usuario y una para la recuperación de información en memorias implementadas en bloques RAM cuyas interfaces hayan sido inutilizadas por SEEs.Todas las propuestas han sido validadas en hardware utilizando una FPGA de Xilinx, la empresa líder en fabricación de dispositivos reconfigurables. De esta forma se proporcionan resultados sobre los impactos de las técnicas propuestas en términos de utilización de recursos, consumos energéticos y máximas frecuencias alcanzables