105 research outputs found
Algorithmic techniques for physical design : macro placement and under-the-cell routing
With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure.
This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time.
The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing.
The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search.
Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi
Algorithmic techniques for physical design : macro placement and under-the-cell routing
With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure.
This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time.
The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing.
The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search.
Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version
Analog layout design automation: ILP-based analog routers
The shrinking design window and high parasitic sensitivity in the advanced technology have imposed special challenges on the analog and radio frequency (RF) integrated circuit design. In this thesis, we propose a new methodology to address such a deficiency based on integer linear programming (ILP) but without compromising the capability of handling any special constraints for the analog routing problems. Distinct from the conventional methods, our algorithm utilizes adaptive resolutions for various routing regions. For a more congested region, a routing grid with higher resolution is employed, whereas a lower-resolution grid is adopted to a less crowded routing region. Moreover, we strengthen its speciality in handling interconnect width control so as to route the electrical nets based on analog constraints while considering proper interconnect width to address the acute interconnect parasitics, mismatch minimization, and electromigration effects simultaneously. In addition, to tackle the performance degradation due to layout dependent effects (LDEs) and take advantage of optical proximity correction (OPC) for resolution enhancement of subwavelength lithography, in this thesis we have also proposed an innovative LDE-aware analog layout migration scheme, which is equipped with our special routing methodology. The LDE constraints are first identified with aid of a special sensitivity analysis and then satisfied during the layout migration process. Afterwards the electrical nets are routed by an extended OPC-inclusive ILP-based analog router to improve the final layout image fidelity while the routability and analog constraints are respected in the meantime. The experimental results demonstrate the effectiveness and efficiency of our proposed methods in terms of both circuit performance and image quality compared to the previous works
RTL-aware dataflow-driven macro placement
© 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.When RTL designers define the hierarchy of a system, they exploit their knowledge about the conceptual abstractions devised during the design and the functional interactions between the logical components. This valuable information is often lost during physical synthesis. This paper proposes a novel multi-level approach for the macro placement problem of complex designs dominated by macro blocks, typically memories. By taking advantage of the hierarchy tree, the netlist is divided into blocks containing macros and standard cells, and their dataflow affinity is inferred considering the latency and flow width of their interaction. The layout is represented using slicing structures and generated with a top-down algorithm capable of handling blocks with both hard and soft components, aimed at wirelength minimization. These techniques have been applied to a set of large industrial circuits and compared against both a commercial floorplanner and handcrafted floorplans by expert back-end engineers. The proposed approach outperforms the commercial tool and produces solutions with similar quality to the best handcrafted floorplans. Therefore, the generated floorplans provide an excellent starting point for the physical design iterations and contribute to reduce turn-around time significantly.Peer ReviewedPostprint (author's final draft
Algorithms for Cell Layout
Cell layout is a critical step in the design process of computer chips. A cell is a logic function or storage element implemented in CMOS technology by transistors connected with wires. As each cell is used many times on a chip, improvements of a single cell layout can have a large effect on the overall chip performance. In the past years increasing difficulty to manufacture small feature sizes has lead to growing complexity of design rules. Producing cell layouts which are compliant with design rules and at the same time optimized w.r.t. layout size has become a difficult task for human experts. In this thesis we present BonnCell, a cell layout generator which is able to fully automatically produce design rule compliant layouts. It is able to guarantee area minimality of its layouts for small and medium sized cells. For large cells it uses a heuristic which produces layouts with a significant area reduction compared to those created manually. The routing problem is based on the Vertex Disjoint Steiner Tree Packing Problem with a large number of additional design rules. In Chapter 4 we present the routing algorithm which is based on a mixed integer programming (MIP) formulation that guarantees compliance with all design rules. The algorithm can also handle instances in which only part of the transistors are placed to check whether this partial placement can be extended to a routable placement of all transistors. Chapter 5 contains the transistor placement algorithm. Based on a branch and bound approach, it places transistors in turn and achieves efficiency by pruning parts of the search tree which do not contain optimum solutions. One major contribution of this thesis is that BonnCell only outputs routable placements. Simply checking the routability for each full placement in the search tree is too slow in practice, therefore several speedup strategies are applied. Some cells are too large to be solved by a single call of the placement algorithm. In Chapter 7 we describe how these cells are split up into smaller subcells which are placed and routed individually and subsequently merged into a placement and routing of the original cell. Two approaches for dividing the original cell into subcells are presented, one based on estimating the subcell area and the other based on solving the Min Cut Linear Arrangement Problem. BonnCell has enabled our cooperation partner IBM to drastically improve their cell design and layout process. In particular, a team of human experts needed several weeks to find a layout for their largest cell, consisting of 128 transistors. BonnCell processed this cell without manual intervention in 3 days and its layout uses 15% less area than the layout found by the human experts
A framework for fine-grain synthesis optimization of operational amplifiers
This thesis presents a cell-level framework for Operational Amplifiers Synthesis (OASYN) coupling both circuit design and layout. For circuit design, the tool applies a corner-driven optimization, accounting for on-chip performance variations. By exploring the process, voltage, and temperature variations space, the tool extracts design worst case solution. The tool undergoes sensitivity analysis along with Pareto-optimality to achieve required specifications. For layout phase, OASYN generates a DRC proved automated layout based on a sized circuit-level description. Morata et al. (1996) introduced an elegant representation of block placement called sequence pair for general floorplans (SP). Like TCG and BSG, but unlike O-tree, B*tree, and CBL, SP is P-admissible. Unlike SP, TCG supports incremental update during operation and keeps the information of the boundary modules as well as their relative positions in the representation. Block placement algorithms that are based on SP use heuristic optimization algorithms, e.g., simulated annealing where generation of large number of sequence pairs are required. Therefore a fast algorithm is needed to generate sequence pairs after each solution perturbation. The thesis presents a new simple and efficient O(n) runtime algorithm for fast realization of incremental update for cost evaluation. The algorithm integrates sequence pair and transitive closure graph advantages into TCG-S* a superior topology update scheme which facilitates the search for optimum desired floorplan. Experiments show that TCG-S* is better than existing works in terms of area utilization and convergence speed. Routing-aware placement is implemented in OASYN, handling symmetry constraints, e.g., interdigitization, common centroid, along with congestion elimination and the enhancement of placement routability
Handling the complexity of routing problem in modern VLSI design
In VLSI physical design, the routing task consists of using over-the-cell metal wires to connect pins and ports of circuit gates and blocks. Traditionally, VLSI routing is an important design step in the sense that the quality of routing solution has great impact on various design metrics such as circuit timing, power consumption, chip reliability and manufacturability etc. As the advancing VLSI design enters the nanometer era, the routing success (routability issue) has been arising as one of the most critical problems in back-end design. In one aspect, the degree of design complexity is increasing dramatically as more and more modules are integrated into the chip. Much higher chip density leads to higher routing demands and potentially more risks in routing failure. In another aspect, with decreasing design feature size, there are more complex design rules imposed to ensure manufacturability. These design rules are hard to satisfy and they usually create more barriers for achieving routing closure (i.e., generate DRC free routing solution) and thus affect chip time to market (TTM) plan.
In general, the behavior and performance of routing are affected by three consecutive phases: placement phase, global routing phase and detailed routing phase in a typical VLSI physical design flow. Traditional CAD tools handle each of the three phases independently and the global picture of the routability issue is neglected. Different from conventional approaches which propose tools and algorithms for one particular design phase, this thesis investigates the routability issue from all three phases and proposes a series of systematic solutions to build a more generic flow and improve quality of results (QoR). For the placement phase, we will introduce a mixed-sized placement refinement tool for alleviating congestion after placement. The tool shifts and relocates modules based on a global routing estimation. For the global routing phase, a very fast and effective global router is developed. Its performance surpasses many peer works as verified by ISPD 2008 global routing contest results. In the detailed routing phase, a tool is proposed to perform detailed routing using regular routing patterns based on a correct-by-construction methodology to improve routability as well as satisfy most design rules. Finally, the tool which integrates global routing and detailed routing is developed to remedy the inconsistency between global routing and detailed routing.
To verify the algorithms we proposed, three sets of testcases derived from ISPD98 and ISPD05/06 placement benchmark suites are proposed. The results indicate that our proposed methods construct an integrated and systematic flow for routability improvement which is better than conventional methods
- …