Free Speech and Its Relation to Self-Government by Alexander Meiklejohn

In today’s system-on-chip (SoC) implementations, power consumption is a key performance specification. The proliferation of mobile communication devices and distributed wireless sensor networks has necessitated the development of power-efficient analog, radio-frequency (RF), and digital integrated circuits. The rapid scaling of CMOS technology nodes presents opportunities and challenges. Benefits accrue in terms of integration density and higher switching speeds for the digital logic. However, the concomitant reduction in supply voltage and reduced gain of transistors pose obstacles to the design of highperformance analog and mixed-signal circuits such as analog front-ends (AFEs) and data converters. To achieve high DC gain, multistage amplifiers are becoming necessary in AFEs and analog-to-digital converters (ADCs) implemented in the latest CMOS process nodes. This thesis includes the design of multistage amplifiers in 40 nm and 65 nm CMOS processes. An AFE for capacitive body-coupled communication is presented with transistor schematic level results in 40 nm CMOS. The AFE consists of a cascade of amplifiers to boost the received signal followed by a Schmitt trigger which provides digital signal levels at the output. Low noise and reduced power consumption are the important performance criteria for the AFE. A two-stage, single-ended amplifier incorporating indirect compensation using split-length transistors has been designed. The compensation technique does not require the nulling resistor used in traditional Miller compensation. The AFE consisting of a cascade of three amplifiers achieves 57.6 dB DC gain with an input-referred noise power spectral density (PSD) of 4.4 nV/ while consuming 6.8 mW. Numerous compensation schemes have been proposed in the literature for multistage amplifiers. Most of these works investigate frequency compensation of amplifiers which drive large capacitive loads and require low unity-gain frequency. In this thesis, the frequency compensation schemes for high-speed, lowvoltage multistage CMOS amplifiers driving small capacitive loads have been investigated. Existing compensation schemes such as the nested Miller compensation with nulling resistor (NMCNR) and reversed nested indirect compensation (RNIC) have been applied to four-stage and three-stage amplifiers designed in 40 nm and 65 nm CMOS, respectively. The performance metrics used for comparing the different frequency compensation schemes are the unity gain  frequency, phase margin (PM), and total amount of compensation capacitance used. From transistor schematic simulation results, it is concluded that RNIC is more efficient than NMCNR. Successive approximation register (SAR) analog-to-digital converters (ADCs) are becoming increasingly popular in a wide range of applications due to their high power efficiency, design simplicity and scaling-friendly architecture. Singlechannel SAR ADCs have reached high resolutions with sampling rates exceeding 50 MS/s. Time-interleaved SAR ADCs have pushed beyond 1 GS/s with medium resolution. The generation and buffering of reference voltages is often not the focus of published works. For high-speed SAR ADCs, due to the sequential nature of the successive approximation algorithm, a high-frequency clock for the SAR logic is needed. As the digital-to-analog converter (DAC) output voltage needs to settle to the desired accuracy within half clock cycle period of the system clock, a speed limitation occurs due to imprecise DAC settling. The situation is exacerbated by parasitic inductance of bondwires and printed circuit board (PCB) traces especially when the reference voltages are supplied off-chip. In this thesis, a power efficient reference voltage buffer with small area has been implemented in 180 nm CMOS for a 10-bit 1 MS/s SAR ADC which is intended to be used in a fingerprint sensor. Since the reference voltage buffer is part of an industrial SoC, critical performance specifications such as fast settling, high power supply rejection ratio (PSRR), and low noise have to be satisfied under mismatch conditions and over the entire range of process, supply voltage and temperature (PVT) corners. A single-ended, current-mirror amplifier with cascodes has been designed to buffer the reference voltage. Performance of the buffer has been verified by exhaustive simulations on the post-layout extracted netlist. Finally, we describe the design of a 10-bit 50 MS/s SAR ADC in 65 nmCMOS with a high-speed, on-chip reference voltage buffer. In a SAR ADC, the capacitive array DAC is the most area-intensive block. Also a binary-weighted capacitor array has a large spread of capacitor values for moderate and high resolutions which leads to increased power consumption. In this work, a split binary-weighted capacitive array DAC has been used to reduce area and power consumption. The proposed ADC has bootstrapped sampling switches which meet 10-bit linearity over all PVT corners and a two-stage dynamic comparator. The important design parameters of the reference voltage buffer are derived in the context of the SAR ADC. The impact of the buffer on the ADC performance is illustrated by simulations using bondwire parasitics. In post-layout simulation which includes the entire pad frame and associated parasitics, the ADC achieves an ENOB of 9.25 bits at a supply voltage of 1.2 V, typical process corner, and sampling frequency of 50 MS/s for near-Nyquist input. Excluding the reference voltage buffer, the ADC achieves an energy efficiency of 25 fJ/conversion-step while occupying a core area of 0.055 mm2

A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

Design of a 4.2-5.4 GHz differential LC VCO using 0.35 mu m SiGeBiCMOS technology for IEEE 802.11a applications

In this paper, a 4.2-5.4 GHz, -Gm LC voltage controlled oscillator (VCO) for IEEE 802.11a standard is presented. The circuit is designed with AMS 0.35 mu m SiGe BiCMOS process that includes high-speed SiGe Heterojunction Bipolar Transistors (HBTs). According to post-layout simulation results, phase noise is -110.7 dBc/Hz at 1 MHz offset from 5.4 GHz carrier frequency and -113.4 dBc/Hz from 4.2 GHz carrier frequency. A linear, 1200 MHz tuning range is obtained from the simulations, utilizing accumulation-mode varactors. Phase noise was also found to be relatively low because of taking advantage of differential tuning concept. Output power of the fundamental frequency changes between 4.8 dBm and 5.5 dBm depending on the tuning voltage. Based on the simulation results, the circuit draws 2 mA without buffers and 14.5 mA from 2.5 V supply including buffer circuits leading to a total power dissipation of 36.25 mW. The circuit layout occupies an area of 0.6 mm(2) on Si substrate, including DC and RF pads

Design of a tunable multi-band differential LC VCO using 0.35 mu m SiGe BiCMOS technology for multi-standard wireless communication systems

In this paper, an integrated 2.2-5.7GHz multi-band differential LC VCO for multi-standard wireless communication systems was designed utilizing 0.35 mu m SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post-layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3 V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78 GHz, 3.22-3.53 GHz, 3.48-3.91 GHz and 4.528-5.7 GHz) with a maximum bandwidth of 1.36 GHz and a minimum bandwidth of 300 MHz. The designed and simulated VCO can generate a differential output power between 0.992 and -6.087 dBm with an average power consumption of 44.21 mW including the buffers. The average second and third harmonics level were obtained as -37.21 and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment. Output power of the fundamental frequency changes between -6.087 and 0.992 dBm, depending on the bias conditions (operating bands). Based on the post-layout simulation results, the core VCO circuit draws a current between 2.4-6.3 mA and between 11.4 and 15.3 mA with the buffer circuit from 3.3 V supply. The circuit occupies an area of 1.477 mm(2) on Si substrate, including DC, digital and RF pads

Design of a 4.2-5.4 GHz Differential LC VCO using 0.35 m SiGe BiCMOS Technology

In this paper, a 4.2-5.4 GHz, Gm LC voltage controlled oscillator (VCO) for IEEE 802.11a standard is presented. The circuit is designed with AMS 0.35´m SiGe BiCMOS process that includes high-speed SiGe Heterojunction Bipolar Transistors (HBTs). Phase noise is -110.7 dBc/Hz at 1MHz offset from 5.4 GHz carrier frequency and -113.5 dBc/Hz from 4.2 GHz carrier frequency. A linear, 1200 MHz tuning range is obtained utilizing accumulation-mode varactors. Phase noise is relatively low due to taking the advantage of differential tuning concept. Output power of the fundamental frequency changes between 4.8 dBm and 5.5 dBm depending on the tuning voltage. The circuit draws 2 mA without buffers and 14.5 mA from 2.5 V supply including buffer circuits leading to a total power dissipation of 36.25 mW. The circuit occupies an area of 0.6 mm2 on Si substrate including RF and DC pads

A 100-MIPS GaAs asynchronous microprocessor

The authors describe how they ported an asynchronous microprocessor previously implemented in CMOS to gallium arsenide, using a technology-independent asynchronous design technique. They introduce new circuits including a sense-amplifier, a completion detection circuit, and a general circuit structure for operators specified by production rules. The authors used and tested these circuits in a variety of designs

Tunable Balun Low-Noise Amplifier in 65nm CMOS Technology

The presented paper includes the design and implementation of a 65 nm CMOS low-noise amplifier (LNA) based on inductive source degeneration. The amplifier is realized with an active balun enabling a single-ended input which is an important requirement for low-cost system on chip implementations. The LNA has a tunable bandpass characteristics from 4.7 GHz up to 5.6 GHz and a continuously tunable gain from 22 dB down to 0 dB, which enables the required flexibility for multi-standard, multi-band receiver architectures. The gain and band tuning is realized with an optimized tunable active resistor in parallel to a tunable L-C tank amplifier load. The amplifier achieves an IIP3 linearity of -8dBm and a noise figure of 2.7 dB at the highest gain and frequency setting with a low power consumption of 10 mW. The high flexibility of the proposed LNA structure together with the overall good performance makes it well suited for future multi-standard low-cost receiver front-ends

Analysis and equalization of data-dependent jitter

Data-dependent jitter limits the bit-error rate (BER) performance of broadband communication systems and aggravates synchronization in phase- and delay-locked loops used for data recovery. A method for calculating the data-dependent jitter in broadband systems from the pulse response is discussed. The impact of jitter on conventional clock and data recovery circuits is studied in the time and frequency domain. The deterministic nature of data-dependent jitter suggests equalization techniques suitable for high-speed circuits. Two equalizer circuit implementations are presented. The first is a SiGe clock and data recovery circuit modified to incorporate a deterministic jitter equalizer. This circuit demonstrates the reduction of jitter in the recovered clock. The second circuit is a MOS implementation of a jitter equalizer with independent control of the rising and falling edge timing. This equalizer demonstrates improvement of the timing margins that achieve 10/sup -12/ BER from 30 to 52 ps at 10 Gb/s