Design of a pressure control system with dead band and time delay

This paper investigates the control of pressure in a hydraulic circuit containing a dead band and a time varying delay. The dead band is considered as a linear term and a perturbation. A sliding mode controller is designed. Stability conditions are established by making use of Lyapunov Krasovskii functionals, non-perfect time delay estimation is studied and a condition for the effect of uncertainties on the dead zone on stability is derived. Also the effect of different LMI formulations on conservativeness is studied. The control law is tested in practice

A path following algorithm for mobile robots

This paper considers path following control for a robotic platform. The vehicle used for the experiments is a specially designed robotic platform for performing autonomous weed control. The platform is four-wheel steered and four-wheel driven. A diesel engine powers the wheels via a hydraulic transmission. The robot uses a Real Time Kinematic Differential Global Positioning System to determine both position and orientation relative to the path. The deviation of the robot to the desired path is supplied to two high level controllers minimizing the orthogonal distance and orientation to the path. Wheel angle setpoints are determined from inversion of the kinematic model. At low level each wheel angle is controlled by a proportional controller combined with a Smith predictor. Results show the controller performance following different paths shapes including a step, a ramp, and a typical headland path. A refined tuning method calculates controller settings that let the robot drive as much as possible along the same path to its setpoint, but also limit the gains at higher speeds to prevent the closed loop system to become unstable due to the time delay in the system. Mean, minimum and maximum orthogonal distance errors while following a straight path on a paving at a speed of 0.5 m/s are 0.0, -2.4 and 3.0 cm respectively and the standard deviation is 1.2 cm. The control method for four wheel steered vehicles presented in this paper has the unique feature that it enables control of a user definable position relative to the robot frame and can deal with limitations on the wheel angles. The method is very well practical applicable for a manufacturer: all parameters needed are known by the manufacturer or can be determined easily, user settings have an easy interpretation and the only complex part can be supplied as a generic software modul

The cosmic X-ray experiment aboard HEAO-1

The HEAO-1 A-2 experiment, designed to study the large scale structure of the galaxy and the universe at X-ray energies is described. The instrument consists of six gas proportional counters of three types nominally covering the energy ranges of 0.15-3 keV, 1.2-20 keV, and 2.5-60 keV. The two low energy detectors have about 400 sq cm open area each while the four others have about 800 sq cm each. Dual field of view collimators allow the unambiguous determination of instrument internal background and diffuse X-ray brightness. Instrument characteristics and early performance are discussed

RRS Discovery Cruise 360, 19 Jan-02 Feb 2011. Trials of the Autosub LR AUV, HyBIS, PELAGRA, Ellsworth Camera and MYRTLE-X Lander systems

There were five main objectives for the trials cruise: The first tests of the Autosub Long Range AUV, testing of the HyBIS video guided grab system, testing of the MYRTLE-X Lander systems, testing of a deep camera system for the Lake Ellsworth probe and test deployments of the PELAGRA neutrally buoyant sediment capture drifters.The working area was about 300 miles south west of the Canary Islands, in international waters, over benthic plains of 4000 m depth, with some tests of the video systems over a isolated sea mount rising to 1200 m depth. Most of the objectives of the cruise where met, with successful diving and control of the Autosub LR, tests of the HyBIS and Ellsworth camera systems, and 3 deployments and recoveries of two PELAGRA floats. Several wire tests of MYRTLE-X systems were carried out, predominantly successful, but concerns over the release system prevented a deployment of the lander

The Drift Chambers Of The Nomad Experiment

We present a detailed description of the drift chambers used as an active target and a tracking device in the NOMAD experiment at CERN. The main characteristics of these chambers are a large area, a self supporting structure made of light composite materials and a low cost. A spatial resolution of 150 microns has been achieved with a single hit efficiency of 97%.Comment: 42 pages, 26 figure

Field test of multi-hop image sensing network prototype on a city-wide scale

Open Access funded by Chongqing University of Posts and Telecommuniocations Under a Creative Commons license, https://creativecommons.org/licenses/by-nc-nd/4.0/Wireless multimedia sensor network drastically stretches the horizon of traditional monitoring and surveillance systems, of which most existing research have utilised Zigbee or WiFi as the communication technology. Both technologies use ultra high frequencies (mainly 2.4 GHz) and suffer from relatively short transmission range (i.e. 100 m line-of-sight). The objective of this paper is to assess the feasibility and potential of transmitting image information using RF modules with lower frequencies (e.g. 433 MHz) in order to achieve a larger scale deployment such as a city scenario. Arduino platform is used for its low cost and simplicity. The details of hardware properties are elaborated in the article, followed by an investigation of optimum configurations for the system. Upon an initial range testing outcome of over 2000 m line-of-sight transmission distance, the prototype network has been installed in a real life city plot for further examination of performance. A range of suitable applications has been proposed along with suggestions for future research.Peer reviewe

Efficient Synthesis of Room Acoustics via Scattering Delay Networks

An acoustic reverberator consisting of a network of delay lines connected via scattering junctions is proposed. All parameters of the reverberator are derived from physical properties of the enclosure it simulates. It allows for simulation of unequal and frequency-dependent wall absorption, as well as directional sources and microphones. The reverberator renders the first-order reflections exactly, while making progressively coarser approximations of higher-order reflections. The rate of energy decay is close to that obtained with the image method (IM) and consistent with the predictions of Sabine and Eyring equations. The time evolution of the normalized echo density, which was previously shown to be correlated with the perceived texture of reverberation, is also close to that of IM. However, its computational complexity is one to two orders of magnitude lower, comparable to the computational complexity of a feedback delay network (FDN), and its memory requirements are negligible

Adaptive feedback analysis and control of programmable stimuli for assessment of cerebrovascular function

The assessment of cerebrovascular regulatory mechanisms often requires flexibly controlled and precisely timed changes in arterial blood pressure (ABP) and/or inspired CO2. In this study, a new system for inducing variations in mean ABP was designed, implemented and tested using programmable sequences and programmable controls to induce pressure changes through bilateral thigh cuffs. The system is also integrated with a computer-controlled switch to select air or a CO2/air mixture to be provided via a face mask. Adaptive feedback control of a pressure generator was required to meet stringent specifications for fast changes, and accuracy in timing and pressure levels applied by the thigh cuffs. The implemented system consists of a PC-based signal analysis/control unit, a pressure control unit and a CO2/air control unit. Initial evaluations were carried out to compare the cuff pressure control performances between adaptive and non-adaptive control configurations. Results show that the adaptive control method can reduce the mean error in sustaining target pressure by 99.57 % and reduce the transient time in pressure increases by 45.21 %. The system has proven a highly effective tool in ongoing research on brain blood flow control