208 research outputs found

    1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

    Get PDF
    A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

    Beam scanning by liquid-crystal biasing in a modified SIW structure

    Get PDF
    A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium

    Advanced Radio Frequency Antennas for Modern Communication and Medical Systems

    Get PDF
    The main objective of this book is to present novel radio frequency (RF) antennas for 5G, IOT, and medical applications. The book is divided into four sections that present the main topics of radio frequency antennas. The rapid growth in development of cellular wireless communication systems over the last twenty years has resulted in most of world population owning smartphones, smart watches, I-pads, and other RF communication devices. Efficient compact wideband antennas are crucial in RF communication devices. This book presents information on planar antennas, cavity antennas, Vivaldi antennas, phased arrays, MIMO antennas, beamforming phased array reconfigurable Pabry-Perot cavity antennas, and time modulated linear array

    Analysis and design of antennas and radiometers for radio astronomy applications in microwave, Mm-wave, and THz Bands

    Get PDF
    Mención Internacional en el título de doctorWe are living in interesting times for astronomy science, since the birth of the radio astronomy field in the 20th century by Karl Jansky, the availability of new and better radio astronomy receivers is in increasing demand to push the human understanding of the universe. In this thesis, various components (antennas, baluns, antenna-arrays, and radiometers) are proposed for radio astronomy receivers. The proposed designs are belonging to three receiver topologies (direct detection, down-conversion, and up-conversion) that operate at different frequency bands from MHz up to a few of THz. Also, to demonstrate that the same proposed design is capable of working efficiently at different operating frequencies, multiple adjusted designs are presented for several practical radio astronomy and space applications. Firstly, a receiver based on the direct detection of the Electromagnetic (EM) radiation through a radio telescope working on cryogenic cooling conditions. In this part, the focus is on designing conical log-spiral antennas and baluns (balanced to unbalanced transformers) to be used as feeds for VLBI Global Observing System (VGOS) ground-based radio telescopes. The feeds cover the Ultrawideband (UWB) from 2 GHz to 14 GHz with Circular Polarization (CP) radiation and stable radiation patterns. After integration of the feeds to the radio telescope, the whole system operates with high aperture efficiency and high System Equivalent Flux Density (SEFD) over the whole required wide range. The fabrication, assembly, and measurements for single-element and four-elements array are provided for achieving the requirements for single CP and dual CP operation. Also, in the same first part, the proposed single-element feed (antenna + balun) is readjusted for being used for CryoRad spaceborne Earth observations. This feed has a single CP over low-frequency UWB from 400MHz to 2 GHz with low weight and physical size compared to standard horn feeds. The second part of the thesis is dedicated to a THz source to be used as a local oscillator for heterodyne radio astronomy THz receivers in which the down-conversion of the THz radiation to a lower frequency occurs. The source is based on an array of self-complementary bow-tie antennas and photomixers that lies on a dielectric lens. The source can be scaled easily to cover different UWB ranges, three ranges are analyzed from 200 GHz to 2 THz, 100 GHz to 1 THz, and 50 GHz to 0.5 THz. Additionally, in this part, a complete study for the effects of metal losses on such THz planar antennas is performed which are not well-investigated in literature yet, the physical explanations behind such effects are also provided. Although these proposed THz sources themselves can work at room temperature, the receiver probably still needs the cooling for the other receiver components (such as the mixer) to work efficiently at such high frequencies. This is the motivation for the third part of this thesis which presents a different type of radio astronomy receiver that is completely able to work without cooling. The third receiver is based on the nonlinear up-converting of the microwave radiation into the optical domain using Whispering Gallery Mode (WGM) resonators which can work at room temperature efficiently. For such advantage and since this concept is naturally narrow-band, it can be a proper candidate for Cosmic Microwave Background (CMB) spectroscopy and space applications. The system design and its performance are analyzed for Ku band at 12 GHz with proposing a novel microwave coupling scheme for enhancing the up-conversion photonic efficiency which is the main limitation for such upconversion systems. Likewise, several high gain 3D-printed Dielectric Resonator Antenna (DRA)s are proposed in both isolated and array configurations to have a direct coupling of the microwave radiation to the proposed scheme. Another practical application for such receiver is presented for CubeSat missions at the mm-wave band (183 GHz) for climate change forecasting. It is clear here that removing the cryogenic cooling conditions decreases satellite weight and cost, which in turn significantly increases its lifetime. Also, it is worth noting that besides the radio astronomy applications, the proposed receivers (and/or their antenna/components) can be used for many other applications. For example, the UWB antennas in the first part can be used as wideband scalable probes for EM compatibility testing or other wireless systems that require single or dual CP such as radar and military applications. This is because the solutions provide constant beam characteristics with good CP polarization purity and stable performance over the operating UWB. In the same way, the proposed THz source in the second part can be used in several THz applications such as very high-speed wireless communications, highresolution imaging for medical and security purposes. This is because of its key benefits as decade bandwidth, compact size, low noise, low power demand, high tunability, and the ability to work at room temperature. For the up-conversion scheme proposed in the third part, due to its high photonic efficiency, low noise level which enables it to work at room temperature, and its scalability from a few GHz up to several THz, it is suitable for low-cost and high sensitivity applications. Specifically, the ones that need to get rid of the hard cryogenic cooling conditions, or at least, relax them and allow the system to work efficiently at higher temperatures. For instance, portable mm-wave and THz systems for quality control, security, and biochemistry. Finally, in this part, the proposed DRA elements and arrays, due to their low cost, high gain, and low losses, can be used for sensing applications and 5G base station antennas.Programa de Doctorado en Multimedia y Comunicaciones por la Universidad Carlos III de Madrid y la Universidad Rey Juan CarlosPresidente: Raed Shubair.- Secretario: Adrián Amor Martín.- Vocal: José Manuel Fernández Gonzále

    Antennas and Propagation

    Get PDF
    This Special Issue gathers topics of utmost interest in the field of antennas and propagation, such as: new directions and challenges in antenna design and propagation; innovative antenna technologies for space applications; metamaterial, metasurface and other periodic structures; antennas for 5G; electromagnetic field measurements and remote sensing applications

    UWB Technology

    Get PDF
    Ultra Wide Band (UWB) technology has attracted increasing interest and there is a growing demand for UWB for several applications and scenarios. The unlicensed use of the UWB spectrum has been regulated by the Federal Communications Commission (FCC) since the early 2000s. The main concern in designing UWB circuits is to consider the assigned bandwidth and the low power permitted for transmission. This makes UWB circuit design a challenging mission in today's community. Various circuit designs and system implementations are published in this book to give the reader a glimpse of the state-of-the-art examples in this field. The book starts at the circuit level design of major UWB elements such as filters, antennas, and amplifiers; and ends with the complete system implementation using such modules

    Applications of Antenna Technology in Sensors

    Get PDF
    During the past few decades, information technologies have been evolving at a tremendous rate, causing profound changes to our world and to our ways of living. Emerging applications have opened u[ new routes and set new trends for antenna sensors. With the advent of the Internet of Things (IoT), the adaptation of antenna technologies for sensor and sensing applications has become more important. Now, the antennas must be reconfigurable, flexible, low profile, and low-cost, for applications from airborne and vehicles, to machine-to-machine, IoT, 5G, etc. This reprint aims to introduce and treat a series of advanced and emerging topics in the field of antenna sensors

    Design and Analysis of Substrate-Integrated Cavity-Backed Antenna Arrays for Ku-Band Applications

    Get PDF
    Mobile communication has become an essential part of our daily life. We love the flexibility of wireless cell phones and even accept their lower quality of service when compared to wired links. Similarly, we are looking forward to the day that we can continue watching our favorite TV programs while travelling anywhere and everywhere. Mobility, flexibility, and portability are the themes of the next generation communication. Motivated and fascinated by such technology breakthroughs, this effort is geared towards enhancing the quality of wireless services and bringing mobile satellite reception one step closer to the market. Meanwhile, phased array antennas are vital components for RADAR applications where the antenna is required to have certain scan capabilities. One of the main concerns in that perspective is how to avoid the potential of scan blindness in the required scan range. Targeting to achieve wide-band wide-scan angle phased arrays free from any scan blindness our efforts is also geared. Conventionally, the key to lower the profile of the antenna is to use planar structures. In that perspective microstrip patch antennas have drawn the attention of antenna engineers since the 1970s due to their attractive features of being low profile, compact size, light weight, and amenable to low-cost PCB fabrication processes. However, patch elements are basically resonating at a single frequency, typically have \u3c2% bandwidth, which is a major deficit that impedes their usage in relatively wide-band applications. There are various approaches to enhance the patch antennas bandwidth including suspended substrates, multi-stack patches, and metalized cavities backing these patches. Metalized cavity-backed patch structures have been demonstrated to give the best performance, however, they are very expensive to manufacture. In this dissertation, we develop an alternative low-cost bandwidth enhancement topology. The proposed topology is based on substrate-integrated waveguides. The great potential of the proposed structure lies in being amenable to the conventional PCB fabrication. Moreover, substrate-integrated cavity-backed structures facilitate the design of sophisticated arrays that are very expensive to develop using the conventional metalized cavity-backed topology, which includes the common broadside arrays used in fixed-beam applications and the scanned phased arrays used in RADAR applications

    Circuit-Theoretic Physics-Based Antenna Synthesis and Design Techniques for Next-Generation Wireless Devices

    Get PDF
    Performance levels expected from future-generation wireless networks and sensor systems are beyond the capabilities of current radio technologies. To realize information capacities much higher than those achievable through existing time and/or frequency coding techniques, an antenna system must exploit the spatial characteristics of the medium in an intelligent and adaptive manner. This means that such system needs to incorporate integrated multi-element antennas with controlled and adjustable performances. The antenna configuration should also be highly miniaturized and integrated with circuits around it in order to meet the rigorous requirements of size, weight, and cost. A solid understanding of the underlying physics of the antenna function is, and has always been, the key to a successful design. In a typical antenna design process, the designer starts with a simple conceptual model, based on a given volume/space to be occupied by the antenna. The design cycle is completed by the antenna performing its function over a range of frequencies in some complex scenarios, i.e., packaged into a compact device, handled in different operational environments, and possibly implanted inside a human/animal body. From the conceptual model to the actual working device, a large variety of design approaches and steps exist. These approaches may be viewed as simulation-driven steps, experimental-based ones, or a hybrid of both. In any of these approaches, a typical design involves a large amount of parametric/optimization steps. It is no wonder, then, that due to the many uncertainties and ‘unknowns’ in the antenna problem, a final working design is usually an evolved version of an initial implementation that comes to fruition only after a considerable amount of effort and time spent on “unsuccessful” prototypes. In general, the circuit/filter community has enjoyed a better design experience than that of the antenna community. Designing a filter network to meet specific bandwidth and insertion loss is a fairly well-defined procedure, from the conceptual stages to the actual realization. In view of the aforementioned, this work focuses on attempting to unveil some of the uncertainties associated with the general antenna design problem through adapting key features from the circuit/filter theory. Some of the adapted features include a group delay method for the design of antennas with a pre-defined impedance bandwidth, inverter-based modeling for the synthesis of small-sized wideband antennas, and an Eigen-based technique to realize multi-band/multi-feed antennas, tunable antennas, and high sensitivity sensor antennas. By utilizing the proposed approaches in the context of this research, the design cycle for practical antennas should be significantly simplified along with various physical limitations clarified, all of which translates to reduced time, effort, and cost in product development.4 month
    corecore