Recent Advances in the mm-Wave Array for Mobile Phones

With the development of communication system to the mm-wave band, the antenna design in the mm-wave band for mobile phones encounters new requirements and challenges. The mm-wave characteristics of short wavelength, high free-space path loss, and easy-to-be-blocking usually require mm-wave antennas with high gain and beam-scanning capability. Also, considering the very limited space occupied by antennas in mobile phones and the massive production of consumer electronics, small size, low cost, multiband, multi-polarization, and wide beam steering becomes the main key point of mm-wave array performance. In addition, as a special situation of the mobile antenna, the analysis of effect of the human tissue on the antenna performance is also important. So, in this chapter, a comprehensive summary on the recent advances in the mm-wave array for mobile phones including single-band, dual-band, and reconfigurable design of broadside array, horizontal polarized, vertical polarized, and dual-polarized design of endfire array, co-design of mm-wave array with lower band antenna, and user influence are summarized

Rotated Half-Mode Substrate Integrated Waveguide and other Planar Integrated Structures

High data rate communication channels are becoming more and more integrated into our increasingly technological society. Substrate Integrated Waveguides (SIW) are one planar solution available to the microwave engineer, offering a low-loss and low dispersion means of propagating these high speed, high bandwidth signals. In this thesis, a brief synopsis of SIW structures and components is presented covering the basic waveguide propagating modes and cut-off frequencies. The main analysis techniques associated with SIWs including full wave electromagnetic modelling methods are overviewed, and the associated loss mechanisms of conduction, dielectric and radiation defined, leading to the design rules and guidelines on how best to mitigate them. SIW antennas as both leaky-wave and radiating slots are discussed and an example of a single and dual resonating slot antenna design is presented, along with a detailed review of a novel switch beam antenna developed for use within the current WiFi bands. The Slot SIW (or SSIW), which has a small longitudinal gap in one of the main conducting surfaces, allows easy integration of lumped elements or active devices, enabling the waveguide to be loaded with impedances or to be shorted. When the slot is shorted, the waveguide reverts back to the full SIW mode, and when partially loaded an intermediate state results. This is discussed, and the SSIW analysed with the transverse resonance technique, leading to the development of a travelling wave attenuator with the SSIW being periodically loaded with pin diodes. The application of the pin diodes required the use of a capacitive overlay, a development of flexi circuit design to allow capacitive coupling of impedances to connect to the waveguide. The overlay concept is extended further, to form novel passive bandpass filters, with the introduction of virtual vias. A limitation of the SSIW is that the majority of the field resides within the dielectric; this allows only a limited interaction with the field at the slot. The rotated Half Mode SIW (rHMSIW), a new variant of the SIW family, places the maximum of the electric field directly on the top dielectric surface, allowing for direct interaction. The waveguide width a is now defined by the dielectric thickness, allowing for the waveguide height b to be adjustable, in normal SIWs this is the other way round; the dielectric thickness fixing the waveguide height and the waveguide width being adjustable. The rHMSIW is characterised with regard to the height and width ratios b/a and the dielectric exposed width (which is adjustable). These parameters effect the modal cut-off frequency, this is investigated and a new equation describing the fundamental mode cut-off frequency is empirically derived. Finally a test coupon which spans the Ku band is designed and measured, which required the development of a novel waveguide transition

Antenna Designs for 5G/IoT and Space Applications

This book is intended to shed some light on recent advances in antenna design for these new emerging applications and identify further research areas in this exciting field of communications technologies. Considering the specificity of the operational environment, e.g., huge distance, moving support (satellite), huge temperature drift, small dimension with respect to the distance, etc, antennas, are the fundamental device allowing to maintain a constant interoperability between ground station and satellite, or different satellites. High gain, stable (in temperature, and time) performances, long lifecycle are some of the requirements that necessitates special attention with respect to standard designs. The chapters of this book discuss various aspects of the above-mentioned list presenting the view of the authors. Some of the contributors are working strictly in the field (space), so they have a very targeted view on the subjects, while others with a more academic background, proposes futuristic solutions. We hope that interested reader, will find a fertile source of information, that combined with their interest/background will allow efficiently exploiting the combination of these two perspectives

Efficient solid state power amplifiers: power combining and highly accurate AM/AM and AM/PM behavioural models with application to linearisation

Radio Frequency (RF) Power Amplifiers (PAs) are a major contributor to modern communication systems, both in terms of being an enabling technology as well as having the most impact on overall system availability, linearity and power consumption. In order to achieve the most optimum system outcome there needs to be an appropriate method for selecting the most suitable RF PA design approach, as well as being able to select the most appropriate RF PA output device, based on a range of varying requirements, specifications and technologies. The ability to perform these tasks quickly, with improved accuracy, using existing available device data, with minimal or no further device testing and from a range of existing and emerging technologies would provide RF PA designers with significant benefits. The investigations and research provided in this thesis consider a range of existing and emerging RF PA technologies and power combining methods and compares them via a new selection and design methodology developed in this thesis. The new methodology builds on modern design and statistical approaches including manufacturing options that enable an appropriate technology to be selected for Solid State Power Amplifier (SSPA) design. In addition to hard design specifications, the current thesis also considers less tangible specifications, such as graceful degradation, time tomarket and ease of use, as well as alternative design approaches, such as fuzzy logic approaches. With a suitable technology approach determined, a selection of a suitable RF output device(s) is considered. As the demand for new communication services continues to increase, requiring tighter specifications and reduced product delivery time scales, then the ability to accurately and quickly compare available RF PA devices from a range of device technologies or devices from different manufacturers, at both the system and component level, makes such a selection paramount. In this thesis, simplememoryless (AmplitudeModulation/AmplitudeModulation (AM/AM) only) and Quasi-Memoryless (QM) Behavioural Models (BMs) (AM/AM combined with Amplitude Modulation/Phase Modulation (AM/PM)) are reviewed, extended and improved upon, with up to 20 dB Normalised Mean Squared Error (NMSE) modelling improvement achieved over a range of technologies, allowing effective RF PA device selection using these newly developed simple and fast models. This thesis uses recent existing accurate and powerful semi-physical memoryless BMs, suited to RF PA devices, and develops and extends their use for QM modelling. The trade-off from the improvement in the overall accuracy is some further simple processing steps. Furthermore, this thesis also provides a comparison of other models, presented in the literature. The improved simple RF PA device models and extension techniques presented in this thesis show, via simulation and measurement, that the new models are suitable for use over a wide range. Lineariser improvements, linked to the accuracy improvements of the proposed models of this thesis, are also investigated, showing further benefits from this research. Physically based simple QM BMs are also used to model thermal and bias network memory effects, which are becomingmore relevant tomodern communication services that use wider bandwidths, enabling the impacts of RF PA device memory effects to be determined and compared. The feasibility of the developed models and improvements are also utilised in the simulation of a low cost RF PA lineariser. With the trend to smaller localised low cost and power RF mobile wireless repeater cells being away from larger more expensive and complex hardware, used to perform linearisation, this thesis presents a trade-off between complexity and linearisation performance and demonstrates, through modelling and simulation, that 8-10 dB improvement in linearisation performance is achievable with the use of the newly developed models.Thesis (Ph.D.) -- University of Adelaide, School of Electrical and Electronic Engineering, 201

Active Backscattering Positioning System Using Innovative Harmonic Oscillator Tags for Future Internet of Things: Theory and Experiments

RÉSUMÉ D'ici 2020, l'Internet des objets (IoT) permettra probablement de créer 25 milliards d'objets connectés, 44 ZB de données et de débloquer 11 000 milliards de dollars d’opportunités commerciales. Par conséquent, ce sujet a suscité d’énormes intérêts de recherche dans le monde académique entier. L'une des technologies clés pour l'IoT concerne le positionnement physique intérieur précis. Le principal objectif dans ce domaine est le développement d'un système de positionnement intérieur avec une grande précision, une haute résolution, un fonctionnement à plusieurs cibles, un faible coût, un faible encombrement et une faible consommation d'énergie. Le système de positionnement intérieur conventionnel basé sur les technologies de Wi-Fi ou d'identification par radiofréquence (RFID) ne peut répondre à ces exigences. Principalement parce que leur appareil et leur signal ne sont pas conçus spécialement pour atteindre les objectifs visés. Les chercheurs ont découvert qu'en mettant en oeuvre de différents types de modulation sur les étiquettes, le radar à onde continue (CW) et ses dérivés deviennent des solutions prometteuses. Les activités de recherche présentées dans cette thèse sont menées dans le but de développer des systèmes de positionnement en intérieur bidimensionnel (2-D) à plusieurs cibles basées sur des étiquettes actives à rétrodiffusion harmonique avec une technique à onde continue modulée en fréquence (FMCW). Les contributions de cette thèse peuvent être résumées comme suit: Tout d'abord, la conception d'un circuit actif harmonique, plus spécifiquement une classe d'oscillateurs harmoniques innovants utilisée comme composant central des étiquettes actives dans notre système, implique une méthodologie de conception de signal de grande taille et des installations de caractérisation. L’analyseur de réseau à grand signal (LSNA) est un instrument émergent basé sur les fondements théoriques du cadre de distorsion polyharmonique (PHD). Bien qu'ils soient disponibles dans le commerce depuis 2008, des organismes de normalisation et de recherche tels que l’Institut national des normes et de la technologie (NIST) des États-Unis travaillent toujours à la mise au point d'un standard largement reconnu permettant d'évaluer et de comparer leurs performances. Dans ce travail, un artefact de génération multi-harmonique pour la vérification LSNA est développé. C'est un dispositif actif capable de générer les 5 premières harmoniques d'un signal d'entrée avec une réponse ultra-stables en amplitude et en phase, quelle que soit la variation de l'impédance de la charge.----------ABSTRACT By 2020, the internet of things (IoT) will probably enable 25 billion connected objects, create 44 ZB data and unlock 11 trillion US dollar business opportunities. Therefore, this topic has been attracting tremendous research interests in the entire academic world. One of the key enabling technologies for IoT is concerned with accurate indoor physical positioning. The development of such an indoor positioning system with high accuracy, high resolution, multitarget operation, low cost, small footprint, and low power consumption is the major objective in this area. The conventional indoor positioning system based on WiFi or radiofrequency identification (RFID) technology cannot fulfill these requirements mainly because their device and signal are not purposely designed for achieving the targeted goals. Researchers have found that by implementing different types of modulation on the tags, continuous-wave (CW) radar and its derivatives become promising solutions. The research activities presented in this Ph.D. thesis are carried out towards the goal of developing multitarget two-dimensional (2-D) indoor positioning systems based on harmonic backscattering active tags together with a frequency-modulated continuous-wave (FMCW) technique. Research contributions of this thesis can be summarized as follows: First of all, the design of a harmonic active circuit, more specifically, a class of innovative harmonic oscillators used as the core component of active tags in our system, involves a large signal design methodology and characterization facilities. The large signal network analyzer (LSNA) is an emerging instrument based on the theoretical foundation for the Poly-Harmonic Distortion (PHD) framework. Although they have been commercially available since 2008, standard and research organizations such as the National Institute of Standards and Technology (NIST) of the US are still working towards a widely-recognized standard to evaluate and cross-reference their performances. In this work, a multi-harmonic generation artifact for LSNA verification is developed. It is an active device that can generate the first 5 harmonics of an input signal with ultra-stable amplitude and phase response regardless of the load impedance variation

In situ underwater microwave oil spill and oil slick thickness sensor

Nearly 30 percent of oil drilled globally is done offshore. Oil spillage offshore have far-reaching consequences on the environment, aquatic lives, and livelihoods as it was evident in the numerous accidents such as the Deepwater Horizon and Bonga oil spillages. Apart from detecting oil spillages, the determination of the oil slick thickness is very important. This is to enable the estimation of the volume and spread of oil discharged in oceans, seas and lakes. This information could guide the oil spill countermeasures and provide the basis for legal actions against the defaulting parties. The viability of the use of radar in the detection of oil spill has already been established by airborne and space borne synthetic aperture radar (SAR). Notwithstanding, the high latency associated with SARs and its susceptibility of false positive and false negative detection of oil slick makes it vulnerable. It has also not been very successful in the determination of oil slick thickness. In situ methods such as the capacitive, conductive and optical based approaches have been used to detect as well as determine oil slick thickness. Some of these contact-based approaches are susceptible to corrosion, fouling and require several calibrations. Radio frequency (RF) signals in seawater suffer from attenuation and dispersion due to the high conductivity of the medium. Antennas, ideally matched to free space, suffer impedance mismatches when immersed in seawater. In this thesis, we proposed the novel approach of using microwave techniques to detect oil spillage and determine oil slick thickness based on a contact-based in situ approach. The work began by undertaking an investigation into the properties of the North Sea water which was used as the primary transmission medium for the study. Subsequently, the research developed an ultrawideband antenna that radiated underwater, which was encapsulated in polydimethylsiloxane (PDMS). The antenna-sensor with a Faraday cage was used to develop a novel microwave oil spill sensor. A communication backbone was designed for the sensor using long range (LoRa) 868 MHz frequency based on a bespoke braid antenna buffered by oil impregnated papers to ameliorate against the influence of the seawater surface. Using a four layered RF switch controller and an antenna array consisting of four antenna-sensors, a novel microwave oil slick thickness sensor was developed. The antenna-sensors were arranged in a cuboid fashion with antenna-sensor 3 and antenna-sensor 4 capable of detecting oil slick thickness at 23 mm and 46 mm using their transmission coefficient (S43) of -10 dB and -19 dB compared to that of the pure seawater respectively. For the 69 mm and 92 mm thickness, the transmission coefficient (S21) of antenna-sensor 1 and antenna-sensor 2 was used to determine these thicknesses with values of -13.5 dB and -24.14 dB with respect to that of pure seawater