Design of low-voltage power efficient frequency dividers in folded MOS current mode logic

In this paper we propose a methodology to design high-speed, power-efficient static frequency dividers based on the low-voltage Folded MOS Current Mode Logic (FMCML) approach. A modeling strategy to analyze the dependence of propagation delay and power consumption on the bias currents of the divide-by-2 (DIV2) cell is introduced. We demonstrate that the behavior of the FMCML DIV2 cell is different both from the one of the conventional MCML DFF (D-type Flip-Flop) and from FMCML DFF without a level shifter. Then an analytical strategy to optimize the divider in different design scenarios: maximum speed, minimum power-delay product (PDP) or minimum energy-delay product (EDP) is presented. The possibility to scale the bias currents through the divider stages without affecting the speed performance is also investigated. The proposed analytical approach allows to gain a deep insight into the circuit behavior and to comprehensively optimize the different design tradeoffs. The derived models and design guidelines are validated against transistor level simulations referring to a commercial 28nm FDSOI CMOS process. Different divide-by-8 circuits following different optimization strategies have been designed in the same 28nm CMOS technology showing the effectiveness of the proposed methodology

A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

Design of Filter Using MOS Current Mode Logic

MCML (MOS Current Mode Logic) is a method used for the purpose of reducing the delay and power of the circuit. In high speed application this method is used to reduce the power. In this method the sleep transistor is inserted in series with the supply voltage (or) current source to reduce the power. Different power gating techniques are been used to reduce the static power and to improve the speed and efficiency of the circuit. In this paper, the filter can be designed by using MCML logic. The fourth order band pass filter by using MCML logic is introduced. In order to reduce the power and delay this method is proposed

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

Design of CMOS integrated frequency synthesizers for ultra-wideband wireless communications systems

Ultra¬wide band (UWB) system is a breakthrough in wireless communication, as it provides data rate one order higher than existing ones. This dissertation focuses on the design of CMOS integrated frequency synthesizer and its building blocks used in UWB system. A mixer¬based frequency synthesizer architecture is proposed to satisfy the agile frequency hopping requirement, which is no more than 9.5 ns, three orders faster than conventional phase¬locked loop (PLL)¬based synthesizers. Harmonic cancela¬tion technique is extended and applied to suppress the undesired harmonic mixing components. Simulation shows that sidebands at 2.4 GHz and 5 GHz are below 36 dBc from carrier. The frequency synthesizer contains a novel quadrature VCO based on the capacitive source degeneration structure. The QVCO tackles the jeopardous ambiguity of the oscillation frequency in conventional QVCOs. Measurement shows that the 5¬GHz CSD¬QVCO in 0.18 µm CMOS technology draws 5.2 mA current from a 1.2 V power supply. Its phase noise is ¬120 dBc at 3 MHz offset. Compared with existing phase shift LC QVCOs, the proposed CSD¬QVCO presents better phase noise and power efficiency. Finally, a novel injection locking frequency divider (ILFD) is presented. Im¬plemented with three stages in 0.18 µm CMOS technology, the ILFD draws 3¬mA current from a 1.8¬V power supply. It achieves multiple large division ratios as 6, 12, and 18 with all locking ranges greater than 1.7 GHz and injection frequency up to 11 GHz. Compared with other published ILFDs, the proposed ILFD achieves the largest division ratio with satisfactory locking range

Phase Synthesis Using Coupled Phase-Locked Loops

Phase Synthesis is a fundamental operation in Smart Antennas and other Phased Array systems based on beamforming. There are increasing commercial applications for Integrated Phased Arrays due to their low cost, size and power and also because the RF and digital signal processing can be performed on the same chip. These low cost beamforming applications have augmented interest in Coupled Phase Locked Loop (CPLL) systems for Phase Synthesis. Previous work on the implementation of Phase Synthesis systems using Coupled PLLs for low cost beamforming had the constraint of a limited phase range of ±90°. The idea behind the thesis is that this phase synthesis range can be increased to ±180° through the use of PLLs employing Phase Frequency Detectors(PFDs), which is a significant improvement over conventional coupled-PLL systems. This work presents the detailed design and measurement results for a phase synthesizer using Coupled PLLs for achieving phase shift in the range of ±180°. Several Coupled PLL architectures are investigated and their advantages and limitations are evaluated in terms of frequency controllability, phase difference synthesis control and phase noise of the systems. A two-PLL system implementation using off the shelf components is presented, which generates a steady-state phase difference in the range ±180° using an adjustable DC control current. This is the proof of concept for doing an IC design for a Coupled Phase Locked Loop system. Commercial applications in the Wireless Medical Telemetry Service (WMTS) band motivate the design of a CPLL system in the 608-614 MHz band. The design methodology is presented which shows the flowchart of the IC design process from the system design specifications to the transistor level design. MATLAB simulations are presented to model the system performance quickly. VerilogA modeling of the CPLL system is performed followed by the IC design of the system and each block is simulated under different process and temperature corners. The transistor level design is then evaluated for its performance in terms of phase difference synthesis and phase noise and compared with the initial MATLAB analysis and improved iteratively. The CPLL system is implemented in IBM 130nm CMOS process and consumes 40mW of power from a 1.2V supply with a phase noise performance of -88 dBc/Hz for 177° phase generation

Flip-Flops for accurate multiphase clocking: transmission gate versus current mode logic

Dynamic transmission gate (DTG) flip-flops (FFs) (DTG-FFs) and current mode logic (CML) FFs (CML-FFs) are compared targeting power efficient multiphase clock generation with low phase error. The effect of component mismatches on multiphase clock timing inaccuracies is modeled and compared, using the product of mismatch-induced jitter variance and power consumption as a figure-of-merit (FOM). Analytical equations are derived to estimate the jitter–power FOM for DTG-FF- and CML-FF- based dividers. Simulations confirm the trends predicted by the equations and show that DTG-FFs achieve a better FOM than CML-FFs. The advantage increases for CMOS processes with smaller feature size and for a lower input frequency compared to $f_T$

Design and implementation of frequency synthesizers for 3-10 ghz mulitband ofdm uwb communication

The allocation of frequency spectrum by the FCC for Ultra Wideband (UWB) communications in the 3.1-10.6 GHz has paved the path for very high data rate Gb/s wireless communications. Frequency synthesis in these communication systems involves great challenges such as high frequency and wideband operation in addition to stringent requirements on frequency hopping time and coexistence with other wireless standards. This research proposes frequency generation schemes for such radio systems and their integrated implementations in silicon based technologies. Special emphasis is placed on efficient frequency planning and other system level considerations for building compact and practical systems for carrier frequency generation in an integrated UWB radio. This work proposes a frequency band plan for multiband OFDM based UWB radios in the 3.1-10.6 GHz range. Based on this frequency plan, two 11-band frequency synthesizers are designed, implemented and tested making them one of the first frequency synthesizers for UWB covering 78% of the licensed spectrum. The circuits are implemented in 0.25µm SiGe BiCMOS and the architectures are based on a single VCO at a fixed frequency followed by an array of dividers, multiplexers and single sideband (SSB) mixers to generate the 11 required bands in quadrature with fast hopping in much less than 9.5 ns. One of the synthesizers is integrated and tested as part of a 3-10 GHz packaged receiver. It draws 80 mA current from a 2.5 V supply and occupies an area of 2.25 mm2. Finally, an architecture for a UWB synthesizer is proposed that is based on a single multiband quadrature VCO, a programmable integer divider with 50% duty cycle and a single sideband mixer. A frequency band plan is proposed that greatly relaxes the tuning range requirement of the multiband VCO and leads to a very digitally intensive architecture for wideband frequency synthesis suitable for implementation in deep submicron CMOS processes. A design in 130nm CMOS occupies less than 1 mm2 while consuming 90 mW. This architecture provides an efficient solution in terms of area and power consumption with very low complexity