Contribution to the design of continuous -time Sigma - Delta Modulators based on time delay elements

The research carried out in this thesis is focused in the development of a new class of data converters for digital radio. There are two main architectures for communication receivers which perform a digital demodulation. One of them is based on analog demodulation to the base band and digitization of the I/Q components. Another option is to digitize the band pass signal at the output of the IF stage using a bandpass Sigma-Delta modulator. Bandpass Sigma- Delta modulators can be implemented with discrete-time circuits, using switched capacitors or continuous-time circuits. The main innovation introduced in this work is the use of passive transmission lines in the loop filter of a bandpass continuous-time Sigma-Delta modulator instead of the conventional solution with gm-C or LC resonators. As long as transmission lines are used as replacement of a LC resonator in RF technology, it seems compelling that transmission lines could improve bandpass continuous-time Sigma-Delta modulators. The analysis of a Sigma- Delta modulator using distributed resonators has led to a completely new family of Sigma- Delta modulators which possess properties inherited both from continuous-time and discretetime Sigma-Delta modulators. In this thesis we present the basic theory and the practical design trade-offs of this new family of Sigma-Delta modulators. Three demonstration chips have been implemented to validate the theoretical developments. The first two are a proof of concept of the application of transmission lines to build lowpass and bandpass modulators. The third chip summarizes all the contributions of the thesis. It consists of a transmission line Sigma-Delta modulator which combines subsampling techniques, a mismatch insensitive circuitry and a quadrature architecture to implement the IF to digital stage of a receiver

A bandpass sigma delta modulator IF receiver

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1997.Includes bibliographical references (leaves 170-173).by Emilija Simic.M.Eng

RF MEMS reference oscillators platform for wireless communications

A complete platform for RF MEMS reference oscillator is built to replace bulky quartz from mobile devices, thus reducing size and cost. The design targets LTE transceivers. A low phase noise 76.8 MHz reference oscillator is designed using material temperature compensated AlN-on-silicon resonator. The thesis proposes a system combining piezoelectric resonator with low loading CMOS cross coupled series resonance oscillator to reach state-of-the-art LTE phase noise specifications. The designed resonator is a two port fundamental width extensional mode resonator. The resonator characterized by high unloaded quality factor in vacuum is designed with low temperature coefficient of frequency (TCF) using as compensation material which enhances the TCF from - 3000 ppm to 105 ppm across temperature ranges of -40˚C to 85˚C. By using a series resonant CMOS oscillator, phase noise of -123 dBc/Hz at 1 kHz, and -162 dBc/Hz at 1MHz offset is achieved. The oscillator’s integrated RMS jitter is 106 fs (10 kHz–20 MHz), consuming 850 μA, with startup time is 250μs, achieving a Figure-of-merit (FOM) of 216 dB. Electronic frequency compensation is presented to further enhance the frequency stability of the oscillator. Initial frequency offset of 8000 ppm and temperature drift errors are combined and further addressed electronically. A simple digital compensation circuitry generates a compensation word as an input to 21 bit MASH 1 -1-1 sigma delta modulator incorporated in RF LTE fractional N-PLL for frequency compensation. Temperature is sensed using low power BJT band-gap front end circuitry with 12 bit temperature to digital converter characterized by a resolution of 0.075˚C. The smart temperature sensor consumes only 4.6 μA. 700 MHz band LTE signal proved to have the stringent phase noise and frequency resolution specifications among all LTE bands. For this band, the achieved jitter value is 1.29 ps and the output frequency stability is 0.5 ppm over temperature ranges from -40˚C to 85˚C. The system is built on 32nm CMOS technology using 1.8V IO device

Bandpass electromechanical sigma-delta modulator

Ph.DDOCTOR OF PHILOSOPH

Bandpass delta-sigma modulators for radio receivers

This thesis concerns discrete-time (DT) bandpass (BP) ΔΣ modulators targeted for intermediate frequency (IF) analog-to-digital (A/D) conversion in radio receivers. The receiver architecture adopted has to be capable of operating with different radio frequencies, channel bandwidths, and modulation techniques. This is necessary in order to achieve an extensive operating area and the possibility of utilizing a local mobile phone standard or a standard suitable for a specific service. The digital IF receiver is a good choice for a multi-mode and multi-band mobile phone receiver, because the signal demodulation and channel filtering are performed in the digital domain. This increases the flexibility of the receiver and relieves the design of the baseband part, but an A/D conversion with high dynamic range and low power dissipation is required. BP ΔΣ modulators are capable of converting a high-frequency narrow band signal and are therefore suitable for signal digitization in an IF receiver. First, the theory of BP ΔΣ modulators is introduced. It has been determined that resonators are the most critical circuit blocks in the implementation of a high performance BP ΔΣ modulator. Different DT resonator topologies are studied and a double-delay (DD) resonator is found to be the best candidate for a high quality resonator. A new DD switched-capacitor (SC) resonator structure has been designed. Furthermore, two evolution versions of the designed SC resonator are presented and their nonidealities are analyzed. The three designed DD SC resonator structures are a main point of the thesis, together with the experimental results. Five different DT BP ΔΣ modulator circuit structures have been implemented and measured. All three of the designed SC resonators are used in the implemented circuits. The experimental work consists of both single-bit and multi-bit structures, as well as both single-loop and cascade architectures. The circuits have been implemented with a 0.35 μm (Bi)CMOS technology and operate with a 3.0 V supply. The measured maximum signal-to-noise-and-distortion ratios (SNDRs) are 78 dB over 270 kHz (GSM), 75 dB over 1.25 MHz (IS-95), 69 dB over 1.762 MHz (DECT), and 48 dB over 3.84 MHz (WCDMA) bandwidths using a 60 MHz IF signal.reviewe

Novel switched-capacitor circuits for delta-sigma modulators

Oversampled delta-sigma modulation is one of the widely used A/D conversion techniques for narrow bandwidth signals. In this study several new lowpass and bandpass delta-sigma modulator architectures as well as novel pseudo-N-path integrators that can be used in implementing these architectures are proposed. By using multiplexing techniques the new lowpass delta-sigma modulator architectures exchange higher clock rates with hardware complexity. For a given oversampling ratio (OSR), the multiplexed first-order delta-sigma modulator achieves a higher resolution. Guaranteed stability is a very desirable feature of these structures. The multi-loop delta-sigma modulator architecture similarly reduces the number of integrators needed to achieve high-resolution conversion for a given OSR. To ensure stability a quantizer with (N+1) bits must be used, where N is the number of loops, or in other words, the order of the delta-sigma modulator. Digital correction or randomizing techniques can be used to eliminate the performance reduction due to digital-to-analog- (D/A) converter nonlinearity error [59], [64]. Bandpass delta-sigma modulators are useful for applications such as AM radio receivers, spectrum analyzers, and digital wireless systems. Using z --> -z[superscript N] or z --> z[superscript N] mapping, a low pass delta-sigma modulator can be transformed to a bandpass one. One of the methods to implement the loop filters in bandpass delta-sigma modulators is to use Pseudo-N-Path (PNP) switched-capacitor (SC) integrators. The advantage is that the center frequency occurs exactly at an integer division of the sampling frequency because of the number of physical paths. To achieve maximum resolution, integrators that do not suffer from clock feedthrough peaks are needed. The proposed differential and single-ended novel PNP integrators address this problem [76]. To keep the opamp specifications less stringent while achieving high resolution, these PNP integrators have been further improved with gain compensation techniques [53]

Some Application of Switched Current Circuits.

A complete digital signal processing system requires analog circuits acting as an interface between the digital system and the outside analog world. Various techniques have been proposed to implement these circuits, but the one compatible with digital technology is switched capacitor (SC) technique. However, there are still some problems with SC circuits which are as follows: (i) The process technology used for these circuits is not compatible with the standard digital process technology due to extra poly-silicon layer, (ii) the performance of these circuits worsens for low voltage operations, because lower supply voltage will tend to increase power consumption for the same dynamic range, and in order to maintain the same dynamic range on a low supply voltage requires a quadratic increase in sampling capacitance to reduce thermal noise. The required increase in bias current to maintain circuit bandwidth results in a net increase in the overall power consumption. To overcome these problems, a new technique called the switched current (SI) technique has been proposed. The technique utilizes the ability of an MOS transistor to maintain its drain current, when its gate is open circuited, through the charge stored on its gate oxide capacitance. In this technique signals are represented by currents instead of voltages and, therefore, the signal swing is only indirectly limited by a reduction of the available voltage range. In a traditional voltage mode circuit, the supply voltage imposes a direct limitation on signal swing. Switched current circuits could therefore be a better for low voltage operation. 5 The application of switched current systems is much same as for switched capacitor systems viz. filters, A/D and D/A converters, general signal processing etc. but the prime aim is that switched current circuits should be implemented using a standard VLSI. In this work, the SI technique has been studied and several reported SI circuits have been simulated for their performance. Specifically, the work was aimed at the study of developing SI technique for the design of high performance circuits such as Integrators, Differentiators, Programmable filters, A/D and D/A converters, Sigma Delta Modulators, Multipliers, Delays etc. All the investigations are based on the PSPICE simulations using model parameters of the BISIM335 MOS transistors. The investigations match the theoretical interpretations and predictions. The entire gamut of this dissertation has been to study the already reported SI circuits and to investigate them for improved accuracy, dynamic range, bandwidth, linearity and low voltage operation

Design and implementation of a wideband sigma delta ADC

Abstract. High-speed and wideband ADCs have become increasingly important in response to the growing demand for high-speed wireless communication services. Continuous time sigma delta modulators (CTƩ∆M), well-known for their oversampling and noise shaping properties, offer a promising solution for low-power and high-speed design in wireless applications. The objective of this thesis is to design and implement a wideband CTƩ∆M for a global navigation satellite system(GNSS) receiver. The targeted modulator architecture is a 3rdorder single-bit CTƩ∆M, specifically designed to operate within a 15 MHz signal bandwidth. With an oversampling ratio of 25, the ADC’s sampling frequency is set at 768 MHz. The design goal is to achieve a theoretical signal to noise ratio (SNR) of 55 dB. This thesis focuses on the design and implementation of the CTƩ∆M, building upon the principles of a discrete time Ʃ∆ modulator, and leveraging system-level simulation and formulations. A detailed explanation of the coefficient calculation procedure specific to CTƩ∆ modulators is provided, along with a "top-down" design approach that ensures the specified requirements are met. MATLAB scripts for coefficient calculation are also included. To overcome the challenges associated with the implementation of CTƩ∆ modulators, particularly excess loop delay and clock jitter sensitivity, this thesis explores two key strategies: the introduction of a delay compensation path and the utilization of a finite impulse response (FIR) feedback DAC. By incorporating a delay compensation path, the stability of the modulator can be ensured and its noise transfer function (NTF) can be restored. Additionally, the integration of an FIR feedback DAC addresses the issue of clock jitter sensitivity, enhancing the overall performance and robustness of the CTƩ∆M. The CTƩ∆Ms employ the cascade of integrators with feed forward (CIFF) and cascade of integrators with feedforward and feedback (CIFF-B) topologies, with a particular emphasis on the CIFF-B configuration using 22nm CMOS technology node and a supply voltage of 0.8 V. Various simulations are performed to validate the modulator’s performance. The simulation results demonstrate an achievable SNR of 55 dB with a power consumption of 1.36 mW. Furthermore, the adoption of NTF zero optimization techniques enhances the SNR to 62 dB.Laajakaistaisen jatkuva-aikaisen sigma delta-AD-muuntimen suunnittelu ja toteutus. Tiivistelmä. Nopeat ja laajakaistaiset AD-muuntimet ovat tulleet entistä tärkeämmiksi nopeiden langattomien kommunikaatiopalvelujen kysynnän kasvaessa. Jatkuva-aikaiset sigma delta -modulaattorit (CTƩ∆M), joissa käytetään ylinäytteistystä ja kohinanmuokkausta, tarjoavat lupaavan ratkaisun matalan tehonkulutuksen ja nopeiden langattomien sovellusten suunnitteluun. Tämän työn tarkoituksena on suunnitella ja toteuttaa laajakaistainen jatkuva -aikainen sigma delta -modulaattori satelliittipaikannusjärjestelmien (GNSS) vastaanottimeen. Arkkitehtuuriltaan modulaattori on kolmannen asteen 1-bittinen CTƩ∆M, jolla on 15MHz:n signaalikaistanleveys. Ylinäytteistyssuhde on 25 ja AD muuntimen näytteistystaajuus 768 MHz. Tavoitteena on saavuttaa teoreettinen 55 dB signaalikohinasuhde (SNR). Tämä työ keskittyy jatkuva-aikaisen sigma delta -modulaattorin suunnitteluun ja toteutukseen, perustuen diskreettiaikaisen Ʃ∆-modulaattorin periaatteisiin ja systeemitason simulointiin ja mallitukseen. Jatkuva-aikaisen sigma delta -modulaattorin kertoimien laskentamenetelmä esitetään yksityiskohtaisesti, ja vaatimusten täyttyminen varmistetaan “top-down” -suunnitteluperiaatteella. Liitteenä on kertoimien laskemiseen käytetty MATLAB-koodi. Jatkuva-aikaisten sigma delta -modulaattoreiden erityishaasteiden, liian pitkän silmukkaviiveen ja kellojitterin herkkyyden, voittamiseksi tutkitaan kahta strategiaa, viiveen kompensointipolkua ja FIR takaisinkytkentä -DA muunninta. Viivekompensointipolkua käyttämällä modulaattorin stabiilisuus ja kohinansuodatusfunktio saadaan varmistettua ja korjattua. Lisäksi FIR takaisinkytkentä -DA-muuntimen käyttö pienentää kellojitteriherkkyyttä, parantaen jatkuva aikaisen sigma delta -modulaattorin kokonaissuorituskykyä ja luotettavuutta. Toteutetuissa jatkuva-aikaisissa sigma delta -modulaattoreissa on kytketty peräkkäin integraattoreita myötäkytkentärakenteella (CIFF) ja toisessa sekä myötä- että takaisinkytkentärakenteella (CIFF-B). Päähuomio on CIFF-B rakenteessa, joka toteutetaan 22nm CMOS prosessissa käyttäen 0.8 voltin käyttöjännitettä. Suorityskyky varmistetaan erilaisilla simuloinneilla, joiden perusteella 55 dB SNR saavutetaan 1.36 mW tehonkulutuksella. Lisäksi kohinanmuokkausfunktion optimoinnilla SNR saadaan nostettua 62 desibeliin