690 research outputs found
Digitally-Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference
A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combination with low-pass filtering to mitigate blockers and improve out-of-band IIP3. Two alternative “iterative” harmonic-rejection (HR) techniques are presented to achieve high HR robust to mismatch: a) an analog two-stage polyphase HR concept, which enhances the HR to more than 60 dB; b) a digital adaptive interference cancelling (AIC) technique, which can suppress one dominating harmonic by at least 80 dB. An accurate multiphase clock generator is presented for a mismatch-robust HR. A proof-of-concept receiver is implemented in 65 nm CMOS. Measurements show 34 dB gain, 4 dB NF, and 3.5 dBm in-band IIP3 while the out-of-band IIP3 is + 16 dBm without fine tuning. The measured RF bandwidth is up to 6 GHz and the 8-phase LO works up to 0.9 GHz (master clock up to 7.2 GHz). At 0.8 GHz LO, the analog two-stage polyphase HR achieves a second to sixth order HR > dB over 40 chips, while the digital AIC technique achieves HR > 80 dB for the dominating harmonic. The total power consumption is 50 mA from a 1.2 V supply
Performance of an Echo Canceller and Channel Estimator for On-Channel Repeaters in DVB-T/H Networks
This paper investigates the design and performance of an FIR echo canceller for on-channel repeaters in DVB-T/H network within the framework of the PLUTO project. The possible
approaches for echo cancellation are briefly reviewed and the main guidelines for the design of such systems are presented. The main system parameters are discussed. The performance of an FIR echo canceller based on an open loop feedforward approach for channel estimation is tested for different radio channel conditions and for different number of taps of the FIR filter. It is shown that a minimum number of taps is recommended to achieve a certain mean rejection ratio or isolation depending on the type of channel. The expected degradation in performance due to the use of fixed point rather than floating point arithmetic in hardware implementation is presented for different number of bits. Channel estimation based on training sequences is investigated. The performance of Maximum Length Sequences and Constant Amplitude Zero Autocorrelation (CAZAC) Sequences is compared for different channels. Recommendations are given for training sequence type, length and
level for DVB-T/H on-channel repeater deployment
Modeling and Efficient Cancellation of Nonlinear Self-Interference in MIMO Full-Duplex Transceivers
This paper addresses the modeling and digital cancellation of
self-interference in in-band full-duplex (FD) transceivers with multiple
transmit and receive antennas. The self-interference modeling and the proposed
nonlinear spatio-temporal digital canceller structure takes into account, by
design, the effects of I/Q modulator imbalances and power amplifier (PA)
nonlinearities with memory, in addition to the multipath self-interference
propagation channels and the analog RF cancellation stage. The proposed
solution is the first cancellation technique in the literature which can handle
such a self-interference scenario. It is shown by comprehensive simulations
with realistic RF component parameters and with two different PA models to
clearly outperform the current state-of-the-art digital self-interference
cancellers, and to clearly extend the usable transmit power range.Comment: 7 pages, 5 figures. To be presented in the 2014 International
Workshop on Emerging Technologies for 5G Wireless Cellular Network
FMCW rail-mounted SAR: Porting spotlight SAR imaging from MATLAB to FPGA
In this work, a low-cost laptop-based radar platform derived from the MIT open courseware has been implemented. It can perform ranging, Doppler measurement and SAR imaging using MATLAB as the processor. In this work, porting the signal processing algorithms onto a FPGA platform will be addressed as well as differences between results obtained using MATLAB and those obtained using the FPGA platform. The target FPGA platforms were a Virtex6 DSP kit and Spartan3A starter kit, the latter was also low-cost to further reduce the cost for students to access radar technology
Robust Automatic Speech recognition System Implemented in a Hybrid Design DSP-FPGA
The aim of this work is to reduce the burden task on the DSP processor by transferring a parallel computation part on a configurable circuits FPGA, in automatic speech recognition module design, signal pre-processing, feature selection and optimization, models construction and finally classification phase are necessary. LMS filter algorithm that contains more parallelism and more MACs (multiply and Accumulate) operations is implemented on FPGA Virtex 5 by Xilings, MFCCs features extraction and DTW ( dynamic time wrapping) method is used as a classifier. Major contribution of this work are hybrid solution DSP and FPGA in real time speech recognition system design, the optimization of number of MAC-core within the FPGA this result is obtained by sharing MAC resources between two operation phases: computation of output filter and updating LMS filter coefficients. The paper also provides a hardware solution of the filter with detailed description of asynchronous interface of FPGA circuit and TMS320C6713-EMIF component. The results of simulation shows an improvement in time computation and by optimizing the implementation on the FPGA a gain in space consumption is obtained
Full-Duplex OFDM Radar With LTE and 5G NR Waveforms: Challenges, Solutions, and Measurements
This paper studies the processing principles, implementation challenges, and
performance of OFDM-based radars, with particular focus on the
fourth-generation Long-Term Evolution (LTE) and fifth-generation (5G) New Radio
(NR) mobile networks' base stations and their utilization for radar/sensing
purposes. First, we address the problem stemming from the unused subcarriers
within the LTE and NR transmit signal passbands, and their impact on
frequency-domain radar processing. Particularly, we formulate and adopt a
computationally efficient interpolation approach to mitigate the effects of
such empty subcarriers in the radar processing. We evaluate the target
detection and the corresponding range and velocity estimation performance
through computer simulations, and show that high-quality target detection as
well as high-precision range and velocity estimation can be achieved.
Especially 5G NR waveforms, through their impressive channel bandwidths and
configurable subcarrier spacing, are shown to provide very good radar/sensing
performance. Then, a fundamental implementation challenge of
transmitter-receiver (TX-RX) isolation in OFDM radars is addressed, with
specific emphasis on shared-antenna cases, where the TX-RX isolation challenges
are the largest. It is confirmed that from the OFDM radar processing
perspective, limited TX-RX isolation is primarily a concern in detection of
static targets while moving targets are inherently more robust to transmitter
self-interference. Properly tailored analog/RF and digital self-interference
cancellation solutions for OFDM radars are also described and implemented, and
shown through RF measurements to be key technical ingredients for practical
deployments, particularly from static and slowly moving targets' point of view.Comment: Paper accepted by IEEE Transactions on Microwave Theory and
Technique
- …