Design and Implementation of a Radix-100 Division Unit

In this thesis, a novel radix-100 divider is designed and implemented. The proposed divider is 3% faster then the current decimal dividers

Efficient FPGA implementation of high-throughput mixed radix multipath delay commutator FFT processor for MIMO-OFDM

This article presents and evaluates pipelined architecture designs for an improved high-frequency Fast Fourier Transform (FFT) processor implemented on Field Programmable Gate Arrays (FPGA) for Multiple Input Multiple Output Orthogonal Frequency Division Multiplexing (MIMO-OFDM). The architecture presented is a Mixed-Radix Multipath Delay Commutator. The presented parallel architecture utilizes fewer hardware resources compared to Radix-2 architecture, while maintaining simple control and butterfly structures inherent to Radix-2 implementations. The high-frequency design presented allows enhancing system throughput without requiring additional parallel data paths common in other current approaches, the presented design can process two and four independent data streams in parallel and is suitable for scaling to any power of two FFT size N. FPGA implementation of the architecture demonstrated significant resource efficiency and high-throughput in comparison to relevant current approaches within literature. The proposed architecture designs were realized with Xilinx System Generator (XSG) and evaluated on both Virtex-5 and Virtex-7 FPGA devices. Post place and route results demonstrated maximum frequency values over 400 MHz and 470 MHz for Virtex-5 and Virtex-7 FPGA devices respectively

Implementation of a Combined OFDM-Demodulation and WCDMA-Equalization Module

For a dual-mode baseband receiver for the OFDMWireless LAN andWCDMA standards, integration of the demodulation and equalization tasks on a dedicated hardware module has been investigated. For OFDM demodulation, an FFT algorithm based on cascaded twiddle factor decomposition has been selected. This type of algorithm combines high spatial and temporal regularity in the FFT data-flow graphs with a minimal number of computations. A frequency-domain algorithm based on a circulant channel approximation has been selected for WCDMA equalization. It has good performance, low hardware complexity and a low number of computations. Its main advantage is the reuse of the FFT kernel, which contributes to the integration of both tasks. The demodulation and equalization module has been described at the register transfer level with the in-house developed Arx language. The core of the module is a pipelined radix-23 butterfly combined with a complex multiplier and complex divider. The module has an area of 0.447 mm2 in 0.18 ¿m technology and a power consumption of 10.6 mW. The proposed module compares favorably with solutions reported in literature

Parametric, Secure and Compact Implementation of RSA on FPGA

We present a fast, efficient, and parameterized modular multiplier and a secure exponentiation circuit especially intended for FPGAs on the low end of the price range. The design utilizes dedicated block multipliers as the main functional unit and Block-RAM as storage unit for the operands. The adopted design methodology allows adjusting the number of multipliers, the radix used in the multipliers, and number of words to meet the system requirements such as available resources, precision and timing constraints. The architecture, based on the Montgomery modular multiplication algorithm, utilizes a pipelining technique that allows concurrent operation of hardwired multipliers. Our design completes 1020-bit and 2040-bit modular multiplications in 7.62 μs and 27.0 μs, respectively. The multiplier uses a moderate amount of system resources while achieving the best area-time product in literature. 2040-bit modular exponentiation engine can easily fit into Xilinx Spartan-3E 500; moreover the exponentiation circuit withstands known side channel attacks

Low Power Implementation of Non Power-of-Two FFTs on Coarse-Grain Reconfigurable Architectures

The DRM standard for digital radio broadcast in the AM band requires integrated devices for radio receivers at very low power. A System on Chip (SoC) call DiMITRI was developed based on a dual ARM9 RISC core architecture. Analyses showed that most computation power is used in the Coded Orthogonal Frequency Division Multiplexing (COFDM) demodulation to compute Fast Fourier Transforms (FFT) and inverse transforms (IFFT) on complex samples. These FFTs have to be computed on non power-of-two numbers of samples, which is very uncommon in the signal processing world. The results obtained with this chip, lead to the objective to decrease the power dissipated by the COFDM demodulation part using a coarse-grain reconfigurable structure as a coprocessor. This paper introduces two different coarse-grain architectures: PACT XPP technology and the Montium, developed by the University of Twente, and presents the implementation of a\ud Fast Fourier Transform on 1920 complex samples. The implementation result on the Montium shows a saving of a factor 35 in terms of processing time, and 14 in terms of power consumption compared to the RISC implementation, and a\ud smaller area. Then, as a conclusion, the paper presents the next steps of the development and some development issues

Low-power Programmable Processor for Fast Fourier Transform Based on Transport Triggered Architecture

This paper describes a low-power processor tailored for fast Fourier transform computations where transport triggering template is exploited. The processor is software-programmable while retaining an energy-efficiency comparable to existing fixed-function implementations. The power savings are achieved by compressing the computation kernel into one instruction word. The word is stored in an instruction loop buffer, which is more power-efficient than regular instruction memory storage. The processor supports all power-of-two FFT sizes from 64 to 16384 and given 1 mJ of energy, it can compute 20916 transforms of size 1024.Comment: 5 pages, 4 figures, 1 table, ICASSP 2019 conferenc

A 64-point Fourier transform chip for high-speed wireless LAN application using OFDM

In this article, we present a novel fixed-point 16-bit word-width 64-point FFT/IFFT processor developed primarily for the application in the OFDM based IEEE 802.11a Wireless LAN (WLAN) baseband processor. The 64-point FFT is realized by decomposing it into a 2-D structure of 8-point FFTs. This approach reduces the number of required complex multiplications compared to the conventional radix-2 64-point FFT algorithm. The complex multiplication operations are realized using shift-and-add operations. Thus, the processor does not use any 2-input digital multiplier. It also does not need any RAM or ROM for internal storage of coefficients. The proposed 64-point FFT/IFFT processor has been fabricated and tested successfully using our in-house 0.25 ?m BiCMOS technology. The core area of this chip is 6.8 mm2. The average dynamic power consumption is 41 mW @ 20 MHz operating frequency and 1.8 V supply voltage. The processor completes one parallel-to-parallel (i. e., when all input data are available in parallel and all output data are generated in parallel) 64-point FFT computation in 23 cycles. These features show that though it has been developed primarily for application in the IEEE 802.11a standard, it can be used for any application that requires fast operation as well as low power consumption

Non-power-of-Two FFTs: Exploring the Flexibility of the Montium TP

Coarse-grain reconfigurable architectures, like the Montium TP, have proven to be a very successful approach for low-power and high-performance computation of regular digital signal processing algorithms. This paper presents the implementation of a class of non-power-of-two FFTs to discover the limitations and Flexibility of the Montium TP for less regular algorithms. A non-power-of-two FFT is less regular compared to a traditional power-of-two FFT. The results of the implementation show the processing time, accuracy, energy consumption and Flexibility of the implementation