Advanced High Efficiency and Broadband Power Amplifiers Based on GaN HEMT for Wireless Applications

In advanced wireless communication systems, a rapid increase in the mobile data traffic and broad information bandwidth requirement can lead to the use of complex spectrally efficient modulation schemes such as orthogonal frequency-division multiplexing (OFDM). Generally, complex non-constant envelope modulated signals have very high peak-to-average ratios (PAPR). Doherty Power Amplifier (DPA) is the most commonly used power amplifier (PA) architecture for meeting high efficiency requirement in advanced communication systems, in the presence of high PAPR signals. However, limited bandwidth of the conventional DPA is often identified as a bottleneck for widespread deployment in base-station application for multi-standard communication signals. The research in this thesis focuses on the development of new designs to overcome the bandwidth limitations of a conventional PA. In particular, the bandwidth limitation factors of a conventional DPA architecture are studied. Moreover, a novel design technique is proposed for DPA’s bandwidth extension. In the first PA design, limited bandwidth and linearity problems are addressed simultaneously. For this purpose, a new Class-AB PA with extended bandwidth and improved linearity is presented for LTE 5 W pico-cell base-station over a frequency range of 1.9–2.5 GHz. A two-tone load/source-pull and bias point optimization techniques are used to extract the sweet spots for optimum efficiency and linearity from the 6 W Cree GaN HEMT device for the whole frequency band. The realized prototype presented saturated PAE higher than 60%, a power gain of 13 dB and an average output power of 36.5 dBm over the desired bandwidth. The proposed PA is also characterized by QAM-256 and LTE input communication signals for linearity characterization. Measured ACPRs are lower than -40 dBc for an input power of 17 dBm. The documented results indicate that the proposed Class-AB architecture is suitable for pico-cell base-station application. In the second PA design, an inherent bandwidth limitation of Class-F power amplifier forced by the improper load harmonics terminations at multiple harmonics is investigated and analyzed. It is demonstrated that the impedance tuning of the second and third harmonics at the drain terminal of a transistor is crucial to achieve a broadband performance. The effect of harmonics terminations on power amplifier’s bandwidth up to fourth harmonics is investigated. The implemented broadband Class-F PA achieved maximum saturated drain efficiency 60-77%, and 10 W output power throughout (1.1-2.1 GHz) band. The simulated and measured results verify that the presented Class-F PA is suitable for a high-efficiency system application in wireless communications over a wide range of frequencies. In the third PA design, a single- and dual-input DPA for LTE application in the 3.5 GHz frequency band are presented and compared. The main goal of this study is to improve the performance of gallium–nitride (GaN) Doherty transmitters over a wide bandwidth in the 3.5 GHz frequency band. For this purpose, the linearity-efficiency trade-off for the two proposed architectures is discussed in detail. Simulated results demonstrate that the single- and dual-input DPA exhibited a peak drain efficiency (DE) of 72.4% and 77%, respectively. Both the circuits showed saturated output power more than 42.9 dBm throughout the designed band. Saturated efficiency, gain and bandwidth of dual-input DPA are higher than that of the single-input DPA. On the other side, dual-input DPA linearity is worse as compared to the single-input DPA. In the last PA design, a novel design methodology for ultra-wide band DPA is presented. The bandwidth limitation factors of the conventional Doherty amplifier are discussed on the ground of broadband matching with impedance variation. To extend the DPA bandwidth, three different methods are used such as post-matching, low impedance transformation ratio and the optimization of offset line for wide bandwidth in the proposed design. The proposed Doherty power amplifier was designed and realized based on two 10 W GaN HEMT devices from Cree Inc. The measured results exhibited 42-57% of efficiency at the 6-dB back-off and saturated output power ranges from 41.5 to 43.1 dBm in the frequency range of 1.15 to 2.35 GHz (68.5% fractional bandwidth). Moreover, less than -25 dBc ACPRs are measured at 42 dBm peak output power throughout the designed band. In a nutshell, all power amplifiers presented in this thesis are suitable for wideband operation and their performances are satisfying the required operational standard. Therefore, this thesis has a significant contribution in the domain of high efficiency and broadband power amplifiers

High efficiency power amplifiers for modern mobile communications: The load-modulation approach

Modern mobile communication signals require power amplifiers able to maintain very high efficiency in a wide range of output power levels, which is a major issue for classical power amplifier architectures. Following the load-modulation approach, efficiency enhancement is achieved by dynamically changing the amplifier load impedance as a function of the input power. In this paper, a review of the widely-adopted Doherty power amplifier and of the other load-modulation efficiency enhancement techniques is presented. The main theoretical aspects behind each method are introduced, and the most relevant practical implementations available in recent literature are reported and discussed

A survey on RF and microwave doherty power amplifier for mobile handset applications

This survey addresses the cutting-edge load modulation microwave and radio frequency power amplifiers for next-generation wireless communication standards. The basic operational principle of the Doherty amplifier and its defective behavior that has been originated by transistor characteristics will be presented. Moreover, advance design architectures for enhancing the Doherty power amplifier’s performance in terms of higher efficiency and wider bandwidth characteristics, as well as the compact design techniques of Doherty amplifier that meets the requirements of legacy 5G handset applications, will be discussed.Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-RFundação para a Ciência e a Tecnologia | Ref. UIDP/50008/201

Amplifier Architectures for Wireless Communication Systems

Ever-increasing demand in modern wireless communication systems leads researchers to focus on design challenges on one of the main components of RF transmitters and receivers, namely amplifiers. On the transmitter side, enhanced efficiency and broader bandwidth over single and multiple bands on power amplifiers will help to have superior performance in communication systems. On the other hand, for the receiver side, having low noise and high gain will be necessary to ensure good quality transmission over such systems. In light of these considerations, a unique approach in design methodologies are studied with low noise amplifiers (LNAs) for RF receivers and the Doherty technique is analyzed for efficiency enhancement for power amplifiers (PA) on the transmitters. This work can be outlined in two parts. In the first part, Low Noise RF amplifier designs with Bipolar Junction Transistor (BJT) are studied to achieve better performing LNAs for receivers. The aim is to obtain a low noise figure while optimizing the bandwidth and achieving a maximum available gain. There are two designs that are operating at different center frequencies and utilizing different transistors. The first design is a wideband low-noise amplifier operating at 2 GHz with a high power BJT. The proposed design uses only distributed elements to realize the input and output matching networks. Additionally, a passive DC bias network is used instead of an active DC bias network to avoid possible complications due to the lumped elements parasitic effects. The matching networks are designed based on the reflection coefficients that are derived based on the transistor’s available regions. The second design is a low voltage standing wave ratio (VSWR) amplifier with a low noise figure operating at 3 GHz. This design is following the same method as in the first design. Both these amplifiers are designed to operate in broadband applications and can be good candidates for base stations. The second part of this work focuses on the transmitter side of communication systems. For this part, Doherty Power Amplifier (DPA) is analyzed as an efficiency enhancement technique for PAs. A modified architecture is proposed to have wider bandwidth and higher efficiency. In the proposed design, the quarter-wave impedance inverter was eliminated. The input and the output of the main and peak amplifiers are matched to the load directly. Additionally, the input and output matching networks are realized only using distributed elements. The selected transistor for this design is a 10 W Gallium Nitride (GaN). The fabricated amplifier operates at the center frequency of 2 GHz and provides 40% fractional bandwidth, 54% of maximum power-added efficiency, and 12.5 dB or better small-signal gain. The design is showing promising results to be a good candidate for better-performing transmitters over the L- and S- band

Efficient and Wideband Load Modulated Power Amplifiers for Wireless Communication

The increasing demand for mobile data traffic has resulted in new challenges and requirements for the development of the wireless communication infrastructure. With the transition to higher frequencies and multi-antenna systems, radio frequency (RF) hardware performance, especially the power amplifier (PA), becomes increasingly important. Enhancing PA energy efficiency and bandwidth is vital for maximizing channel capacity, reducing operational costs, and facilitating integration.In the first part of the thesis, the bandwidth limitations of the standard two-way Doherty PA are discussed. A comprehensive analysis is provided, and the frequency responses of different Doherty combiner networks are presented. Furthermore, a Doherty combiner network is proposed, notable for its inherent broadband frequency and its capacity to account for the influence of output parasitics and packaged components from the active devices. The introduced Doherty combiner network is experimentally verified by a wideband gallium nitride (GaN) Doherty PA operating over 1.6-2.7 GHz.In the second part of the thesis, an analytically based combiner synthesis approach for the three-stage Doherty PA is proposed and presented. A compact output combiner network, together with the input phase delays, is derived directly from transistor load-pull data and the PA design requirements. The technique opens up new design space for three-stage Doherty PAs with reconfigurable high-efficiency power back-off levels. The utility of the proposed technique is demonstrated by the implementation of a 30-W GaN three-stage Doherty PA prototype at 2.14 GHz. Measurements show that a drain efficiency of 68% and 55% is exhibited at 6- and 10-dB back-off power, respectively.In the third part, a new PA architecture named the circulator load modulated amplifier (CLMA), is proposed. This architecture utilizes active load modulation for achieving enhanced back-off efficiency. Two active devices are incorporated in this innovative architecture, and a non-reciprocal circulator-based combiner is leveraged. Following this, the sequential CLMA (SCLMA) is introduced, characterized by its ability to enhance back-off efficiency without the necessity of load modulation. GaN demonstrator circuits for both CLMA and SCLMA architectures, whether with dual-input or RF single-input, are designed and fabricated, with excellent performance being measured.\ua0The thesis contributes novel design techniques and architectures to enhance PA efficiency and bandwidth. These findings pave the way for energy-efficient and adaptable RF transmitters in future wireless communication systems

Advanced High Efficiency Architectures for Next Generation Wireless Communications

L'abstract è presente nell'allegato / the abstract is in the attachmen

Concurrent Dual-band Doherty Power Amplifiers for Carrier Aggregation

Carrier aggregation is the main feature of the Long Term Evolution advanced (LTE-A) standard to increase the spectral efficiency and communication bandwidth. It calls for wireless transmitters to be multi-band and multi-standard to meet the demands of various deployment scenarios. In addition, these transmit radios must efficiently amplify signals characterized with a high peak-to-average power ratio (PAPR), which is caused by advanced modulation schemes. These two factors highlight the need for the multi-band Doherty power amplifier (DPA), which allows the transmitter remain in high efficiency at back-off power levels and maintain that high efficiency over multiple frequency bands. In this work, a novel output combining network is presented for the dual-band DPA design with extended fractional bandwidth for carrier aggregated signals. The proposed output combiner employs a modified Pi-shape network, which enables the absorption of output capacitances from both the main and peaking devices and eliminates the need for phase offset lines which are major sources of bandwidth limitation in the existing multiband DPAs. In addition to performing the impedance inversion, the proposed combiner incorporates the biasing feeds and presents small low-frequency impedances to both the main and peaking transistors. The inclusion of the bias feeds and small low low-frequency impedance feature improves the linearizability of the DPA when stimulated with concurrent dual-band modulated signals. Lastly, by using the gain contour at the back-off power level, the non-linear AM-AM response caused by the varying input capacitance of the main transistor is mitigated. The proposed dual-band output power combiner and the back-off gain contour technique were applied to design of a dual-band two-way Doherty PA using the commercialized 25W Gallium Nitride (GaN) transistor. Measurement of the two-way DPA shows a gain of 7.5- 9.5 dB at 2.05 - 2.3 GHz and 9 - 11 dB at 3.2 - 3.62 GHz. The efficiency at 6 dB back off is greater than 49% and 47% across the two frequency bands. The linearizability of the dual-band DPA is validated using various carrier aggregated signals. The PA exhibits linear behaviour when driven by up to 80 MHz intra-band carrier aggregated signal and 20 MHz concurrent dual-band signal after DPD. Additionally, carrier aggregated signals usually lead to a PAPR value between 8-10 dB. The efficiency of classic two-way DPA deteriorates when dealing with such signals. To cope with the efficiency deterioration, a three-way DPA was designed. Simulations of the three-way DPA show that the gain is greater than 9 dB within the two frequency bands, 2.05 - 2.32 GHz and 3.35 - 3.65 GHz. The efficiency at 10-dB back-off is greater than 40% in the two frequency bands

Parallel Doherty RF Power Amplifier For WiMAX Applications

abstract: This work covers the design and implementation of a Parallel Doherty RF Power Amplifier in a GaN HEMT process for medium power macro-cell (16W) base station applications. This work improves the key parameters of a Doherty Power Amplifier including the peak and back-off efficiency, operational instantaneous bandwidth and output power by proposing a Parallel Doherty amplifier architecture. As there is a progression in the wireless communication systems from the first generation to the future 5G systems, there is ever increasing demand for higher data rates which means signals with higher peak-to-average power ratios (PAPR). The present modulation schemes require PAPRs close to 8-10dB. So, there is an urgent need to develop energy efficient power amplifiers that can transmit these high data rate signals. The Doherty Power Amplifier (DPA) is the most common PA architecture in the cellular infrastructure, as it achieves reasonably high back-off power levels with good efficiency. This work advances the DPA architecture by proposing a Parallel Doherty Power Amplifier to broaden the PAs instantaneous bandwidth, designed with frequency range of operation for 2.45 – 2.70 GHz to support WiMAX applications and future broadband signals.Dissertation/ThesisMasters Thesis Electrical Engineering 201

Recent Developments of Dual-Band Doherty Power Amplifiers for Upcoming Mobile Communications Systems

Power amplifiers in modern and future communications should be able to handle different modulation standards at different frequency bands, and in addition, to be compatible with the previous generations. This paper reviews the recent design techniques that have been used to operate dual-band amplifiers and in particular the Doherty amplifiers. Special attention is focused on the design methodologies used for power splitters, phase compensation networks, impedance inverter networks and impedance transformer networks of such power amplifier. The most important materials of the dual-band Doherty amplifier are highlighted and surveyed. The main problems and challenges covering dual-band design concepts are presented and discussed. In addition, improvement techniques to enhance such operations are also exploited. The study shows that the transistor parasitic has a great impact in the design of a dual-band amplifier, and reduction of the transforming ratio of the inverter simplifies the dual-band design. The offset line can be functionally replaced by a Π-network in dual-band design rather than T-network