Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Improving reconfigurable systems reliability by combining periodical test and redundancy techniques: a case study

This paper revises and introduces to the field of reconfigurable computer systems, some traditional techniques used in the fields of fault-tolerance and testing of digital circuits. The target area is that of on-board spacecraft electronics, as this class of application is a good candidate for the use of reconfigurable computing technology. Fault tolerant strategies are used in order for the system to adapt itself to the severe conditions found in space. In addition, the paper describes some problems and possible solutions for the use of reconfigurable components, based on programmable logic, in space applications

Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review

The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER

The development of a node for a hardware reconfigurable parallel processor

This dissertation concerns the design and implementation of a node for a hardware reconfigurable parallel processor. The hardware that was developed allows for the further development of a parallel processor with configurable hardware acceleration. Each node in the system has a standard microprocessor and reconfigurable logic device and has high speed communications channels for inter-node communication. The design of the node provided high-speed serial communications channels allowing the implementation of various network topographies. The node also provided a PCI master interface to provide an external interface and communicate with local nodes on the bus. A high speed RlSC processor provided communication and system control functions and the reconfigurable logic device provided communication interfaces and data processing functions. The node was designed and implemented as a PCI card that interfaced a standard PCI bus. VHDL designs for logic devices that provided system support were developed, VHDL designs for the reconfigurable logic FPGA and software including drivers and system software were written for the node. The 64-bit version Linux operating system was then ported to the processor providing a UNIX environment for the system. The node functioned as specified and parallel and hardware accelerated processing was demonstrated. The hardware acceleration was shown to provide substantial performance benefits for the system

H-SIMD machine : configurable parallel computing for data-intensive applications

This dissertation presents a hierarchical single-instruction multiple-data (H-SLMD) configurable computing architecture to facilitate the efficient execution of data-intensive applications on field-programmable gate arrays (FPGAs). H-SIMD targets data-intensive applications for FPGA-based system designs. The H-SIMD machine is associated with a hierarchical instruction set architecture (HISA) which is developed for each application. The main objectives of this work are to facilitate ease of program development and high performance through ease of scheduling operations and overlapping communications with computations. The H-SIMD machine is composed of the host, FPGA and nano-processor layers. They execute host SIMD instructions (HSIs), FPGA SIMD instructions (FSIs) and nano-processor instructions (NPLs), respectively. A distinction between communication and computation instructions is intended for all the HISA layers. The H-SIMD machine also employs a memory switching scheme to bridge the omnipresent large bandwidth gaps in configurable systems. To showcase the proposed high-performance approach, the conditions to fully overlap communications with computations are investigated for important applications. The building blocks in the H-SLMD machine, such as high-performance and area-efficient register files, are presented in detail. The H-SLMD machine hierarchy is implemented on a host Dell workstation and the Annapolis Wildstar II FPGA board. Significant speedups have been achieved for matrix multiplication (MM), 2-dimensional discrete cosine transform (2D DCT) and 2-dimensional fast Fourier transform (2D FFT) which are used widely in science and engineering. In another FPGA-based programming paradigm, a high-level language (here ANSI C) can be used to program the FPGAs in a mode similar to that of the H-SIMD machine in terms of trying to minimize the effect of overheads. More specifically, a multi-threaded overlapping scheme is proposed to reduce as much as possible, or even completely hide, runtime FPGA reconfiguration overheads. Nevertheless, although the HLL-enabled reconfigurable machine allows software developers to customize FPGA functions easily, special architecture techniques are needed to achieve high-performance without significant penalty on area and clock frequency. Two important high-performance applications, matrix multiplication and image edge detection, are tested on the SRC-6 reconfigurable machine. The implemented algorithms are able to exploit the available data parallelism with independent functional units and application-specific cache support. Relevant performance and design tradeoffs are analyzed