An Effective Low Power Ring Oscillator Based All Digital Phase Locked Loop

The All digital phase-locked loops (ADPLL) widely employed in the data communication systems including, but not limited to, the implementation of the frequency multiplication and clock synchronization circuits. A phase-interpolator is utilized for power consumption reduction by using TDC in a ring-oscillator in a fractional-N phase-locked loop. A predicted-phase-interpolation method is used to calculate the integer and fractional parts of the frequency-division-ratio and to find two interpolation clocks. The prediction method gives a significant power reduction in the proposed PIFC by enabling the use of low-frequency clocks for phase interpolatio

Design of energy efficient high speed I/O interfaces

Energy efficiency has become a key performance metric for wireline high speed I/O interfaces. Consequently, design of low power I/O interfaces has garnered large interest that has mostly been focused on active power reduction techniques at peak data rate. In practice, most systems exhibit a wide range of data transfer patterns. As a result, low energy per bit operation at peak data rate does not necessarily translate to overall low energy operation. Therefore, I/O interfaces that can scale their power consumption with data rate requirement are desirable. Rapid on-off I/O interfaces have a potential to scale power with data rate requirements without severely affecting either latency or the throughput of the I/O interface. In this work, we explore circuit techniques for designing rapid on-off high speed wireline I/O interfaces and digital fractional-N PLLs. A burst-mode transmitter suitable for rapid on-off I/O interfaces is presented that achieves 6 ns turn-on time by utilizing a fast frequency settling ring oscillator in digital multiplying delay-locked loop and a rapid on-off biasing scheme for current mode output driver. Fabricated in 90 nm CMOS process, the prototype achieves 2.29 mW/Gb/s energy efficiency at peak data rate of 8 Gb/s. A 125X (8 Gb/s to 64 Mb/s) change in effective data rate results in 67X (18.29 mW to 0.27 mW) change in transmitter power consumption corresponding to only 2X (2.29 mW/Gb/s to 4.24 mW/Gb/s) degradation in energy efficiency for 32-byte long data bursts. We also present an analytical bit error rate (BER) computation technique for this transmitter under rapid on-off operation, which uses MDLL settling measurement data in conjunction with always-on transmitter measurements. This technique indicates that the BER bathtub width for 10^(−12) BER is 0.65 UI and 0.72 UI during rapid on-off operation and always-on operation, respectively. Next, a pulse response estimation-based technique is proposed enabling burst-mode operation for baud-rate sampling receivers that operate over high loss channels. Such receivers typically employ discrete time equalization to combat inter-symbol interference. Implementation details are provided for a receiver chip, fabricated in 65nm CMOS technology, that demonstrates efficacy of the proposed technique. A low complexity pulse response estimation technique is also presented for low power receivers that do not employ discrete time equalizers. We also present techniques for implementation of highly digital fractional-N PLL employing a phase interpolator based fractional divider to improve the quantization noise shaping properties of a 1-bit ∆Σ frequency-to-digital converter. Fabricated in 65nm CMOS process, the prototype calibration-free fractional-N Type-II PLL employs the proposed frequency-to-digital converter in place of a high resolution time-to-digital converter and achieves 848 fs rms integrated jitter (1 kHz-30 MHz) and -101 dBc/Hz in-band phase noise while generating 5.054 GHz output from 31.25 MHz input

RF MEMS reference oscillators platform for wireless communications

A complete platform for RF MEMS reference oscillator is built to replace bulky quartz from mobile devices, thus reducing size and cost. The design targets LTE transceivers. A low phase noise 76.8 MHz reference oscillator is designed using material temperature compensated AlN-on-silicon resonator. The thesis proposes a system combining piezoelectric resonator with low loading CMOS cross coupled series resonance oscillator to reach state-of-the-art LTE phase noise specifications. The designed resonator is a two port fundamental width extensional mode resonator. The resonator characterized by high unloaded quality factor in vacuum is designed with low temperature coefficient of frequency (TCF) using as compensation material which enhances the TCF from - 3000 ppm to 105 ppm across temperature ranges of -40˚C to 85˚C. By using a series resonant CMOS oscillator, phase noise of -123 dBc/Hz at 1 kHz, and -162 dBc/Hz at 1MHz offset is achieved. The oscillator’s integrated RMS jitter is 106 fs (10 kHz–20 MHz), consuming 850 μA, with startup time is 250μs, achieving a Figure-of-merit (FOM) of 216 dB. Electronic frequency compensation is presented to further enhance the frequency stability of the oscillator. Initial frequency offset of 8000 ppm and temperature drift errors are combined and further addressed electronically. A simple digital compensation circuitry generates a compensation word as an input to 21 bit MASH 1 -1-1 sigma delta modulator incorporated in RF LTE fractional N-PLL for frequency compensation. Temperature is sensed using low power BJT band-gap front end circuitry with 12 bit temperature to digital converter characterized by a resolution of 0.075˚C. The smart temperature sensor consumes only 4.6 μA. 700 MHz band LTE signal proved to have the stringent phase noise and frequency resolution specifications among all LTE bands. For this band, the achieved jitter value is 1.29 ps and the output frequency stability is 0.5 ppm over temperature ranges from -40˚C to 85˚C. The system is built on 32nm CMOS technology using 1.8V IO device

All-Digital Phase-Locked Loop for Radio Frequency Synthesis

It has been a constant challenge in wireless system design to meet the growing demand for an ever higher data rate and more diversified functionality at minimal cost and power consumption. The key lies in exploiting the phenomenal success of CMOS technology scaling for high-level integration. This underlies the paradigm shift in the field of integrated circuit (IC) design to one that increasingly favours digital circuits as opposed to their analog counterparts. With radio transceiver design for wireless systems in particular, a noticeable trend is the introduction of digital-intensive solutions for traditional analog functions. A prominent example is the emergence of the all-digital phase-locked loop (ADPLL) architectures for frequency synthesis. By avoiding traditional analog blocks, the ADPLL brings the benefits of high-level integration and improved programmability. This thesis presents ADPLL frequency synthesizer design, highlighting practical design considerations and technical innovations. Three prototype designs using a 65-nm CMOS technology are presented. The first example address a low-power ADPLL design for 2.4-GHz ISM (Industrial, Scientific, Medical) band frequency synthesis. A high-speed topology is employed in the implementation for the variable phase accumulator to count full cycles of the radio frequency (RF) output. A simple technique based on a short delay line in the reference signal path allows the time-to-digital converter (TDC) core to operate at a low duty cycle with approximately 95% reduction in its average power consumption. The ADPLL incorporates a two-point modulation scheme with an adaptive gain calibration to allow for direct frequency modulation. The second implementation is a wide-band ADPLL-based frequency synthesizer for cognitive radio sensor units. It employs a digitally controlled ring oscillator with an LC tank introduced to extend the tuning range and reduce power dissipation. An adaptive frequency calibration technique based on binary search is used for fast frequency settling. The third implementation is another wideband ADPLL frequency synthesizer. At the architectural level, separation of coarse-tune and fine-tune branches results in a word length reduction for both of them and allows the coarse tuning logic to be powered off or clock gated during normal operation, which led to a significant reduction in the area and power consumption for the digital logic and simplified the digital design. A dynamic binary search technique was proposed to achieve further improved frequency calibration speed compared with previous techniques. In addition, an original technique was employed for the frequency tuning of the wideband ring oscillator to allow for compact design and excellent linearity

Performance enhancement techniques for low power digital phase locked loops

Desire for low-power, high performance computing has been at core of the symbiotic union between digital circuits and CMOS scaling. While digital circuit performance improves with device scaling, analog circuits have not gained these benefits. As a result, it has become necessary to leverage increased digital circuit performance to mitigate analog circuit deficiencies in nanometer scale CMOS in order to realize world class analog solutions. In this thesis, both circuit and system enhancement techniques to improve performance of clock generators are discussed. The following techniques were developed: (1) A digital PLL that employs an adaptive and highly efficient way to cancel the effect of supply noise, (2) a supply regulated DPLL that uses low power regulator and improves supply noise rejection, (3) a digital multiplying DLL that obviates the need for high-resolution TDC while achieving sub-picosecond jitter and excellent supply noise immunity, and (4) a high resolution TDC based on a switched ring oscillator, are presented. Measured results obtained from the prototype chips are presented to illustrate the proposed design techniques

Millimeter-Wave CMOS Digitally Controlled Oscillators for Automotive Radars

All-Digital-Phase-Locked-Loops (ADPLLs) are ideal for integrated circuit implementations and effectively generate frequency chirps for Frequency-Modulated-Continuous-Wave (FMCW) radar. This dissertation discusses the design requirements for integrated ADPLL, which is used as chirp synthesizer for FMCW automotive radar and focuses on an analysis of the ADPLL performance based on the Digitally-Controlled-Oscillator (DCO) design parameters and the ADPLL configuration. The fundamental principles of the FMCW radar are reviewed and the importance of linear DCO for reliable operation of the synthesizer is discussed. A novel DCO, which achieves linear frequency tuning steps is designed by arranging the available minimum Metal-Oxide-Metal (MoM) capacitor in unique confconfigurations. The DCO prototype fabricated in 65 nm CMOS fullls the requirements of the 77 GHz automotive radar. The resultant linear DCO characterization can effectively drive a chirp generation system in complete FMCW automotive radar synthesizer

Research Reports: 1984 NASA/ASEE Summer Faculty Fellowship Program

A NASA/ASEE Summer Faulty Fellowship Program was conducted at the Marshall Space Flight Center (MSFC). The basic objectives of the programs are: (1) to further the professional knowledge of qualified engineering and science faculty members; (2) to stimulate an exchange of ideas between participants and NASA; (3) to enrich and refresh the research and teaching activities of the participants' institutions; and (4) to contribute to the research objectives of the NASA Centers. The Faculty Fellows spent ten weeks at MSFC engaged in a research project compatible with their interests and background and worked in collaboration with a NASA/MSFC colleague. This document is a compilation of Fellows' reports on their research during the summer of 1984. Topics covered include: (1) data base management; (2) computational fluid dynamics; (3) space debris; (4) X-ray gratings; (5) atomic oxygen exposure; (6) protective coatings for SSME; (7) cryogenics; (8) thermal analysis measurements; (9) solar wind modelling; and (10) binary systems

Delta-Sigma FDC Based Fractional-N PLLs with Multi-Rate Quantizing Dynamic Element Matching

Fractional-N phase-locked loop (PLL) frequency synthesizers are ubiquitous in modern communication systems, where they are used to synthesize a signal of high spectral purity from a reference signal of much lower frequency. In order to meet the requirements of wireless communication standard, strict limitation are placed on the spectral content of the synthesized signal. In recent years, PLL based on time-to-digital converters (TDC-PLLs) have been proposed that aim at moving the complexity of the design from the analog section to the digital section of the synthesizer : the advantages are a reduction in area, cost and power consumption over competing architectures based on delta-sigma modulation and charge pumps ([Delta][Sigma]-PLLs). Although TDC-PLLs with good performance have been demonstrated, TDC quantization noise has so far kept their phase noise and spurious tone performance below that of the best comparable [Delta][Sigma]-PLLs. An alternative approach is to use a delta-sigma frequency-to-digital converter ([Delta][Sigma]FDC) in place of a TDC to retain the benefits of TDC-PLLs and [Delta][Sigma]-PLLs. Chapter 1 describes a practical [Delta][Sigma] FDC based PLL in which the quantization noise is equivalent to that of a [Delta][Sigma]-PLL. It presents a linearized model of the PLL, design criteria to avoid spurious tones in the [Delta][Sigma] FDC quantization noise, and a design methodology for choosing the loop parameters in terms of standard PLL target specifications. Chapter 2 presents a multi-rate quantizing dynamic element matching (DEM) encoder for digital to analog converters (DACs) that allows a significant reduction in the encoder power consumption with respect to a conventional encoder for oversampling DEM DACs, at the expense of a minimal signal- to-noise ratio reduction. In Chapter 3, the implementation details of a [Delta][Sigma] FDC based fractional-N phase- locked loop prototype are shown. The PLL was built to showcase the capability of the architecture analyzed in Chapter 1 to comply with the most stringent wireless communication standards. The prototype extends the architecture described in Chapter 1 by including an FDC quantization noise cancelling algorithm, and an hardware efficient implementation of a multi-rate quantizing DEM encoder for digital to frequency conversio