AirSync: Enabling Distributed Multiuser MIMO with Full Spatial Multiplexing

The enormous success of advanced wireless devices is pushing the demand for higher wireless data rates. Denser spectrum reuse through the deployment of more access points per square mile has the potential to successfully meet the increasing demand for more bandwidth. In theory, the best approach to density increase is via distributed multiuser MIMO, where several access points are connected to a central server and operate as a large distributed multi-antenna access point, ensuring that all transmitted signal power serves the purpose of data transmission, rather than creating "interference." In practice, while enterprise networks offer a natural setup in which distributed MIMO might be possible, there are serious implementation difficulties, the primary one being the need to eliminate phase and timing offsets between the jointly coordinated access points. In this paper we propose AirSync, a novel scheme which provides not only time but also phase synchronization, thus enabling distributed MIMO with full spatial multiplexing gains. AirSync locks the phase of all access points using a common reference broadcasted over the air in conjunction with a Kalman filter which closely tracks the phase drift. We have implemented AirSync as a digital circuit in the FPGA of the WARP radio platform. Our experimental testbed, comprised of two access points and two clients, shows that AirSync is able to achieve phase synchronization within a few degrees, and allows the system to nearly achieve the theoretical optimal multiplexing gain. We also discuss MAC and higher layer aspects of a practical deployment. To the best of our knowledge, AirSync offers the first ever realization of the full multiuser MIMO gain, namely the ability to increase the number of wireless clients linearly with the number of jointly coordinated access points, without reducing the per client rate.Comment: Submitted to Transactions on Networkin

Low-overhead fault-tolerant logic for field-programmable gate arrays

While allowing for the fabrication of increasingly complex and efficient circuitry, transistor shrinkage and count-per-device expansion have major downsides: chiefly increased variation, degradation and fault susceptibility. For this reason, design-time consideration of faults will have to be given to increasing numbers of electronic systems in the future to ensure yields, reliabilities and lifetimes remain acceptably high. Many mathematical operators commonly accelerated in hardware are suited to modification resulting in datapath error detection and correction capabilities with far lower area, performance and/or power consumption overheads than those incurred through the utilisation of more established, general-purpose fault tolerance methods such as modular redundancy. Field-programmable gate arrays are uniquely placed to allow further area savings to be made thanks to their dynamic reconfigurability. The majority of the technical work presented within this thesis is based upon a benchmark hardware accelerator---a matrix multiplier---that underwent several evolutions in order to detect and correct faults manifesting along its datapath at runtime. In the first instance, fault detectability in excess of 99% was achieved in return for 7.87% additional area and 45.5% extra latency. In the second, the ability to correct errors caused by those faults was added at the cost of 4.20% more area, while 50.7% of this---and 46.2% of the previously incurred latency overhead---was removed through the introduction of partial reconfiguration in the third. The fourth demonstrates further reductions in both area and performance overheads---of 16.7% and 8.27%, respectively---through systematic data width reduction by allowing errors of less than ±0.5% of the maximum output value to propagate.Open Acces

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria

A Survey and Comparative Study of Hard and Soft Real-time Dynamic Resource Allocation Strategies for Multi/Many-core Systems

Multi-/many-core systems are envisioned to satisfy the ever-increasing performance requirements of complex applications in various domains such as embedded and high-performance computing. Such systems need to cater to increasingly dynamic workloads, requiring efficient dynamic resource allocation strategies to satisfy hard or soft real-time constraints. This article provides an extensive survey of hard and soft real-time dynamic resource allocation strategies proposed since the mid-1990s and highlights the emerging trends for multi-/many-core systems. The survey covers a taxonomy of the resource allocation strategies and considers their various optimization objectives, which have been used to provide comprehensive comparison. The strategies employ various principles, such as market and biological concepts, to perform the optimizations. The trend followed by the resource allocation strategies, open research challenges, and likely emerging research directions have also been provided

Autonomous Recovery Of Reconfigurable Logic Devices Using Priority Escalation Of Slack

Field Programmable Gate Array (FPGA) devices offer a suitable platform for survivable hardware architectures in mission-critical systems. In this dissertation, active dynamic redundancy-based fault-handling techniques are proposed which exploit the dynamic partial reconfiguration capability of SRAM-based FPGAs. Self-adaptation is realized by employing reconfiguration in detection, diagnosis, and recovery phases. To extend these concepts to semiconductor aging and process variation in the deep submicron era, resilient adaptable processing systems are sought to maintain quality and throughput requirements despite the vulnerabilities of the underlying computational devices. A new approach to autonomous fault-handling which addresses these goals is developed using only a uniplex hardware arrangement. It operates by observing a health metric to achieve Fault Demotion using Recon- figurable Slack (FaDReS). Here an autonomous fault isolation scheme is employed which neither requires test vectors nor suspends the computational throughput, but instead observes the value of a health metric based on runtime input. The deterministic flow of the fault isolation scheme guarantees success in a bounded number of reconfigurations of the FPGA fabric. FaDReS is then extended to the Priority Using Resource Escalation (PURE) online redundancy scheme which considers fault-isolation latency and throughput trade-offs under a dynamic spare arrangement. While deep-submicron designs introduce new challenges, use of adaptive techniques are seen to provide several promising avenues for improving resilience. The scheme developed is demonstrated by hardware design of various signal processing circuits and their implementation on a Xilinx Virtex-4 FPGA device. These include a Discrete Cosine Transform (DCT) core, Motion Estimation (ME) engine, Finite Impulse Response (FIR) Filter, Support Vector Machine (SVM), and Advanced Encryption Standard (AES) blocks in addition to MCNC benchmark circuits. A iii significant reduction in power consumption is achieved ranging from 83% for low motion-activity scenes to 12.5% for high motion activity video scenes in a novel ME engine configuration. For a typical benchmark video sequence, PURE is shown to maintain a PSNR baseline near 32dB. The diagnosability, reconfiguration latency, and resource overhead of each approach is analyzed. Compared to previous alternatives, PURE maintains a PSNR within a difference of 4.02dB to 6.67dB from the fault-free baseline by escalating healthy resources to higher-priority signal processing functions. The results indicate the benefits of priority-aware resiliency over conventional redundancy approaches in terms of fault-recovery, power consumption, and resource-area requirements. Together, these provide a broad range of strategies to achieve autonomous recovery of reconfigurable logic devices under a variety of constraints, operating conditions, and optimization criteria

DC-Patch: A Microarchitectural Fault Patching Technique for GPU Register Files

The ever-increasing parallelism demand of General-Purpose Graphics Processing Unit (GPGPU) applications pushes toward larger and more energy-hungry register files in successive GPU generations. Reducing the supply voltage beyond its safe limit is an effective way to improve the energy efficiency of register files. However, at these operating voltages, the reliability of the circuit is compromised. This work aims to tolerate permanent faults from process variations in large GPU register files operating below the safe supply voltage limit. To do so, this paper proposes a microarchitectural patching technique, DC-Patch, exploiting the inherent data redundancy of applications to compress registers at run-time with neither compiler assistance nor instruction set modifications. Instead of disabling an entire faulty register file entry, DC-Patch leverages the reliable cells within a faulty entry to store compressed register values. Experimental results show that, with more than a third of faulty register entries, DC-Patch ensures a reliable operation of the register file and reduces the energy consumption by 47% with respect to a conventional register file working at nominal supply voltage. The energy savings are 21% compared to a voltage noise smoothing scheme operating at the safe supply voltage limit. These benefits are obtained with less than 2 and 6% impact on the system performance and area, respectively

Speeding-up model-based fault injection of deep-submicron CMOS fault models through dynamic and partially reconfigurable FPGAS

Actualmente, las tecnologías CMOS submicrónicas son básicas para el desarrollo de los modernos sistemas basados en computadores, cuyo uso simplifica enormemente nuestra vida diaria en una gran variedad de entornos, como el gobierno, comercio y banca electrónicos, y el transporte terrestre y aeroespacial. La continua reducción del tamaño de los transistores ha permitido reducir su consumo y aumentar su frecuencia de funcionamiento, obteniendo por ello un mayor rendimiento global. Sin embargo, estas mismas características que mejoran el rendimiento del sistema, afectan negativamente a su confiabilidad. El uso de transistores de tamaño reducido, bajo consumo y alta velocidad, está incrementando la diversidad de fallos que pueden afectar al sistema y su probabilidad de aparición. Por lo tanto, existe un gran interés en desarrollar nuevas y eficientes técnicas para evaluar la confiabilidad, en presencia de fallos, de sistemas fabricados mediante tecnologías submicrónicas. Este problema puede abordarse por medio de la introducción deliberada de fallos en el sistema, técnica conocida como inyección de fallos. En este contexto, la inyección basada en modelos resulta muy interesante, ya que permite evaluar la confiabilidad del sistema en las primeras etapas de su ciclo de desarrollo, reduciendo por tanto el coste asociado a la corrección de errores. Sin embargo, el tiempo de simulación de modelos grandes y complejos imposibilita su aplicación en un gran número de ocasiones. Esta tesis se centra en el uso de dispositivos lógicos programables de tipo FPGA (Field-Programmable Gate Arrays) para acelerar los experimentos de inyección de fallos basados en simulación por medio de su implementación en hardware reconfigurable. Para ello, se extiende la investigación existente en inyección de fallos basada en FPGA en dos direcciones distintas: i) se realiza un estudio de las tecnologías submicrónicas existentes para obtener un conjunto representativo de modelos de fallos transitoriosAndrés Martínez, DD. (2007). Speeding-up model-based fault injection of deep-submicron CMOS fault models through dynamic and partially reconfigurable FPGAS [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/1943Palanci