1,934 research outputs found
Near-field direct antenna modulation
NFDAM systems provide a unique solution for transmitting highly secured direction-dependent data and hence preventing eavesdroppers from properly demodulating the signal. A 60-GHz proof-of-concept chip was designed and measured
Building an end user focused THz based ultra high bandwidth wireless access network: The TERAPOD approach
The TERAPOD project aims to investigate and demonstrate the feasibility of ultra high bandwidth wireless access networks operating in the Terahertz (THz) band. The proposed TERAPOD THz communication system will be developed, driven by end user usage scenario requirements and will be demonstrated within a first adopter operational setting of a Data Centre. In this article, we define the full communications stack approach that will be taken in TERAPOD, highlighting the specific challenges and aimed innovations that are targeted
Channel Characterization for Chip-scale Wireless Communications within Computing Packages
Wireless Network-on-Chip (WNoC) appears as a promising alternative to
conventional interconnect fabrics for chip-scale communications. WNoC takes
advantage of an overlaid network composed by a set of millimeter-wave antennas
to reduce latency and increase throughput in the communication between cores.
Similarly, wireless inter-chip communication has been also proposed to improve
the information transfer between processors, memory, and accelerators in
multi-chip settings. However, the wireless channel remains largely unknown in
both scenarios, especially in the presence of realistic chip packages. This
work addresses the issue by accurately modeling flip-chip packages and
investigating the propagation both its interior and its surroundings. Through
parametric studies, package configurations that minimize path loss are obtained
and the trade-offs observed when applying such optimizations are discussed.
Single-chip and multi-chip architectures are compared in terms of the path loss
exponent, confirming that the amount of bulk silicon found in the pathway
between transmitter and receiver is the main determinant of losses.Comment: To be presented 12th IEEE/ACM International Symposium on
Networks-on-Chip (NOCS 2018); Torino, Italy; October 201
A Wideband 77-GHz, 17.5-dBm Fully Integrated Power Amplifier in Silicon
A 77-GHz, +17.5 dBm power amplifier (PA) with fully integrated 50-Ω input and output matching and fabricated in a 0.12-µm SiGe BiCMOS process is presented. The PA achieves a peak power gain of 17 dB and a maximum single-ended output power of 17.5 dBm with 12.8% of power-added efficiency (PAE). It has a 3-dB bandwidth of 15 GHz and draws 165 mA from a 1.8-V supply. Conductor-backed coplanar waveguide (CBCPW) is used as the transmission line structure resulting in large isolation between adjacent lines, enabling integration of the PA in an area of 0.6 mm^2. By using a separate image-rejection filter incorporated before the PA, the rejection at IF frequency of 25 GHz is improved by 35 dB, helping to keep the PA design wideband
MIDAS: Automated Approach to Design Microwave Integrated Inductors and Transformers on Silicon
The design of modern radiofrequency integrated circuits on silicon operating at microwave and millimeter-waves requires the integration of several spiral inductors and transformers that are not commonly available in the process design-kits of the technologies. In this work we present an auxiliary CAD tool for Microwave Inductor (and transformer) Design Automation on Silicon (MIDAS) that exploits commercial simulators and allows the implementation of an automatic design flow, including three-dimensional layout editing and electromagnetic simulations. In detail, MIDAS allows the designer to derive a preliminary sizing of the inductor (transformer) on the bases of the design entries (specifications). It draws the inductor (transformer) layers for the specific process design kit, including vias and underpasses, with or without patterned ground shield, and launches the electromagnetic simulations, achieving effective design automation with respect to the traditional design flow for RFICs. With the present software suite the complete design time is reduced significantly (typically 1 hour on a PC based on Intel® Pentium® Dual 1.80GHz CPU with 2-GB RAM). Afterwards both the device equivalent circuit and the layout are ready to be imported in the Cadence environment
Antennas at Millimetre Waves
Millimeter wave is today’s breakthrough frontier for emerging wireless mobile cellular networks, wireless local and personal area networks, simultaneous energy/data transfer, wearable networks, vehicular communications and radar. In the near future, millimeter wave applications, devices, and networks will change our world. Millimeter wave is regarded as a solution to an unprecedented challenge to overcome a global bandwidth shortage owning to an ever increase demand for higher data rates and more reliable service capabilities for wireless devices, wireless service providers are facing, thanks to the
massive amount of raw bandwidth
and potential multigigabit-per-second
(Gb/s) data rates. This article introduces the basic challenges and initial opportunities for millimeter wave engineering, with an emphasize on 5G antenna design
Computational polarimetric microwave imaging
We propose a polarimetric microwave imaging technique that exploits recent
advances in computational imaging. We utilize a frequency-diverse cavity-backed
metasurface, allowing us to demonstrate high-resolution polarimetric imaging
using a single transceiver and frequency sweep over the operational microwave
bandwidth. The frequency-diverse metasurface imager greatly simplifies the
system architecture compared with active arrays and other conventional
microwave imaging approaches. We further develop the theoretical framework for
computational polarimetric imaging and validate the approach experimentally
using a multi-modal leaky cavity. The scalar approximation for the interaction
between the radiated waves and the target---often applied in microwave
computational imaging schemes---is thus extended to retrieve the susceptibility
tensors, and hence providing additional information about the targets.
Computational polarimetry has relevance for existing systems in the field that
extract polarimetric imagery, and particular for ground observation. A growing
number of short-range microwave imaging applications can also notably benefit
from computational polarimetry, particularly for imaging objects that are
difficult to reconstruct when assuming scalar estimations.Comment: 17 pages, 15 figure
CCAT-prime: Science with an Ultra-widefield Submillimeter Observatory at Cerro Chajnantor
We present the detailed science case, and brief descriptions of the telescope
design, site, and first light instrument plans for a new ultra-wide field
submillimeter observatory, CCAT-prime, that we are constructing at a 5600 m
elevation site on Cerro Chajnantor in northern Chile. Our science goals are to
study star and galaxy formation from the epoch of reionization to the present,
investigate the growth of structure in the Universe, improve the precision of
B-mode CMB measurements, and investigate the interstellar medium and star
formation in the Galaxy and nearby galaxies through spectroscopic,
polarimetric, and broadband surveys at wavelengths from 200 um to 2 mm. These
goals are realized with our two first light instruments, a large field-of-view
(FoV) bolometer-based imager called Prime-Cam (that has both camera and an
imaging spectrometer modules), and a multi-beam submillimeter heterodyne
spectrometer, CHAI. CCAT-prime will have very high surface accuracy and very
low system emissivity, so that combined with its wide FoV at the unsurpassed
CCAT site our telescope/instrumentation combination is ideally suited to pursue
this science. The CCAT-prime telescope is being designed and built by Vertex
Antennentechnik GmbH. We expect to achieve first light in the spring of 2021.Comment: Presented at SPIE Millimeter, Submillimeter, and Far-Infrared
Detectors and Instrumentation for Astronomy IX, June 14th, 201
Millimeter-wave Evolution for 5G Cellular Networks
Triggered by the explosion of mobile traffic, 5G (5th Generation) cellular
network requires evolution to increase the system rate 1000 times higher than
the current systems in 10 years. Motivated by this common problem, there are
several studies to integrate mm-wave access into current cellular networks as
multi-band heterogeneous networks to exploit the ultra-wideband aspect of the
mm-wave band. The authors of this paper have proposed comprehensive
architecture of cellular networks with mm-wave access, where mm-wave small cell
basestations and a conventional macro basestation are connected to
Centralized-RAN (C-RAN) to effectively operate the system by enabling power
efficient seamless handover as well as centralized resource control including
dynamic cell structuring to match the limited coverage of mm-wave access with
high traffic user locations via user-plane/control-plane splitting. In this
paper, to prove the effectiveness of the proposed 5G cellular networks with
mm-wave access, system level simulation is conducted by introducing an expected
future traffic model, a measurement based mm-wave propagation model, and a
centralized cell association algorithm by exploiting the C-RAN architecture.
The numerical results show the effectiveness of the proposed network to realize
1000 times higher system rate than the current network in 10 years which is not
achieved by the small cells using commonly considered 3.5 GHz band.
Furthermore, the paper also gives latest status of mm-wave devices and
regulations to show the feasibility of using mm-wave in the 5G systems.Comment: 17 pages, 12 figures, accepted to be published in IEICE Transactions
on Communications. (Mar. 2015
- …