Millimeter-wave Communication and Radar Sensing — Opportunities, Challenges, and Solutions

With the development of communication and radar sensing technology, people are able to seek for a more convenient life and better experiences. The fifth generation (5G) mobile network provides high speed communication and internet services with a data rate up to several gigabit per second (Gbps). In addition, 5G offers great opportunities of emerging applications, for example, manufacture automation with the help of precise wireless sensing. For future communication and sensing systems, increasing capacity and accuracy is desired, which can be realized at millimeter-wave spectrum from 30 GHz to 300 GHz with several tens of GHz available bandwidth. Wavelength reduces at higher frequency, this implies more compact transceivers and antennas, and high sensing accuracy and imaging resolution. Challenges arise with these application opportunities when it comes to realizing prototype or demonstrators in practice. This thesis proposes some of the solutions addressing such challenges in a laboratory environment.High data rate millimeter-wave transmission experiments have been demonstrated with the help of advanced instrumentations. These demonstrations show the potential of transceiver chipsets. On the other hand, the real-time communication demonstrations are limited to either low modulation order signals or low symbol rate transmissions. The reason for that is the lack of commercially available high-speed analog-to-digital converters (ADCs); therefore, conventional digital synchronization methods are difficult to implement in real-time systems at very high data rates. In this thesis, two synchronous baseband receivers are proposed with carrier recovery subsystems which only require low-speed ADCs [A][B].Besides synchronization, high-frequency signal generation is also a challenge in millimeter-wave communications. The frequency divider is a critical component of a millimeter-wave frequency synthesizer. Having both wide locking range and high working frequencies is a challenge. In this thesis, a tunable delay gated ring oscillator topology is proposed for dual-mode operation and bandwidth extension [C]. Millimeter-wave radar offers advantages for high accuracy sensing. Traditional millimeter-wave radar with frequency-modulated continuous-wave (FMCW), or continuous-wave (CW), all have their disadvantages. Typically, the FMCW radar cannot share the spectrum with other FMCW radars.\ua0 With limited bandwidth, the number of FMCW radars that could coexist in the same area is limited. CW radars have a limited ambiguous distance of a wavelength. In this thesis, a phase-modulated radar with micrometer accuracy is presented [D]. It is applicable in a multi-radar scenario without occupying more bandwidth, and its ambiguous distance is also much larger than the CW radar. Orthogonal frequency-division multiplexing (OFDM) radar has similar properties. However, its traditional fast calculation method, fast Fourier transform (FFT), limits its measurement accuracy. In this thesis, an accuracy enhancement technique is introduced to increase the measurement accuracy up to the micrometer level [E]

On the benefits of phase shift keying to optical telecommunication systems

Les avantages de la modulation de phase vis-à-vis la modulation d’intensité pour les réseaux optiques sont claires et accepté par la communauté scientifique des télécommunications optiques. Surtout, la modulation de phase montre une meilleure sensibilité au bruit, ainsi qu’une plus grande tolérance aux effets non-linéaires que la modulation d’intensité. Nous présentons dans cette thése un étude qui vise à développer les avantages de la modulation de phase. Nous attaquons d’abord la complexité du récepteur en détection directe, en proposant une nouvelle configuration dont la complexité est comparable à celle du récepteur pour la modulation d’intensité traditionnel, mais avec des meilleures performances. Cette solution pourrait convenir pour les réseaux métropolitains (et même d’accès) à haut débit binaire. Nous passons ensuite à l’examen de la possibilité d’utiliser des amplificateur à semi-conducteur (SOA) au lieu des amplificateurs à fibre dopée à l’erbium pour fournir amplification optique aux signaux modulés en phase. Les non-linéarité des SOA sont étudiées, et un compensateur simple et très efficace est proposé. Les avantages des amplificateurs à semi-conducteur par rapport à ceux à fibre sont bien connus. Surtout, la méthode que nous proposons permettrait l’integrabilité des SOA avec d’autres composants de réseau (par exemple, le récepteur nommé cidessus), menant à des solutions technologiques de petite taille et efficaces d’un point de vue énergétique. Il y a deux types de systèmes pour signaux modulés en phase: basé sur la détection directe, ou sur les récepteurs cohérents. Dans le dernière partie de ce travail, nous nous concentrons sur cette dernière catégorie, et nous comparons deux solutions possibles pour la mise à niveau des réseaux terrestres actuel. Nous comparons deux configurations dont les performances sont très comparables en termes de sensibilité au bruit, mais nous montrons comment la meilleure tolérance aux effets non linéaires (en particuliers dans les systèmes à débit mixte) fait que une solution soit bien plus efficace que l’autre.The advantages of phase modulation (PM) vis-à-vis intensity modulation for optical networks are accepted by the optical telecommunication community. PM exhibits a higher noise sensitivity than intensity modulation, and it is more tolerant to the effects of fiber nonlinearity. In this thesis we examine the challenges and the benefits of working with different aspects of phase modulation. Our first contribution tackles the complexity of the direct detection noncoherent receiver for differentially encoded quadrature phase shift keying. We examine a novel configuration whose complexity is comparable to that of traditional receivers for intensity modulation, yet outperforming it. We show that under severe nonlinear impairments, our proposed receiver works almost as well as the conventional receiver, with the advantage of being much less complex. We also show that the proposed receiver is tolerant to chromatic dispersion, and to detuning of the carrier frequency. This solution might be suitable for high-bit rates metro (and even access) networks. Our second contribution deals with the challenges of using semiconductor optical amplifiers (SOAs) instead of typical erbium doped fiber amplifiers (EDFAs) to provide amplification to phase modulated signals. SOAs nonlinearities are investigated, and we propose a simple and very effective feed-forward compensator. Above all, the method we propose would permit the integrability of SOAs with other network components (for example, the aforementioned receiver) achieving small size, power efficient sub-systems. Phase modulation paves the way to high spectral efficiency, especially when paired with digital coherent receivers. With the digital coherent receiver, the degree of freedom offered by polarization can be exploited to increase the channel bit rate without increasing its spectral occupancy. In the last part of this work we focus on polarization multiplexed signaling paired with coherent reception and digital signal processing. Our third contribution provides insight on the strategies for upgrading current terrestrial core networks to high bit rates. This is a particularly challenging scenario, as phase modulation has to coexist with previously installed intensity modulated channels. We compare two configurations which have received much attention in the literature. These solutions show comparable performance in terms of back-to-back noise sensitivity, and yet are not equivalent. We show how the superior tolerance to nonlinear fiber propagation (and particularly to cross phase modulation induced by the presence of intensity modulated channels) makes one of them much more effective than the other

Design of low power CMOS UWB transceiver ICs

Master'sMASTER OF ENGINEERIN

Development and Experimental Analysis of Wireless High Accuracy Ultra-Wideband Localization Systems for Indoor Medical Applications

This dissertation addresses several interesting and relevant problems in the field of wireless technologies applied to medical applications and specifically problems related to ultra-wideband high accuracy localization for use in the operating room. This research is cross disciplinary in nature and fundamentally builds upon microwave engineering, software engineering, systems engineering, and biomedical engineering. A good portion of this work has been published in peer reviewed microwave engineering and biomedical engineering conferences and journals. Wireless technologies in medicine are discussed with focus on ultra-wideband positioning in orthopedic surgical navigation. Characterization of the operating room as a medium for ultra-wideband signal transmission helps define system design requirements. A discussion of the first generation positioning system provides a context for understanding the overall system architecture of the second generation ultra-wideband positioning system outlined in this dissertation. A system-level simulation framework provides a method for rapid prototyping of ultra-wideband positioning systems which takes into account all facets of the system (analog, digital, channel, experimental setup). This provides a robust framework for optimizing overall system design in realistic propagation environments. A practical approach is taken to outline the development of the second generation ultra-wideband positioning system which includes an integrated tag design and real-time dynamic tracking of multiple tags. The tag and receiver designs are outlined as well as receiver-side digital signal processing, system-level design support for multi-tag tracking, and potential error sources observed in dynamic experiments including phase center error, clock jitter and drift, and geometric position dilution of precision. An experimental analysis of the multi-tag positioning system provides insight into overall system performance including the main sources of error. A five base station experiment shows the potential of redundant base stations in improving overall dynamic accuracy. Finally, the system performance in low signal-to-noise ratio and non-line-of-sight environments is analyzed by focusing on receiver-side digitally-implemented ranging algorithms including leading-edge detection and peak detection. These technologies are aimed at use in next-generation medical systems with many applications including surgical navigation, wireless telemetry, medical asset tracking, and in vivo wireless sensors