Fuzzy Controller for Matrix Converter System to Improve its Quality of Output

In this paper, Fuzzy Logic controller is developed for ac/ac Matrix Converter. Furthermore, Total Harmonic Distortion is reduced significantly. Space Vector Algorithm is a method to improve power quality of the converter output. But its quality is limited to 86.7%.We are introduced a Cross coupled DQ axis controller to improve power quality. The Matrix Converter is an attractive topology for High voltage transformation ratio. A Matlab / Simulink simulation analysis of the Matrix Converter system is provided. The design and implementation of fuzzy controlled Matrix Converter is described. This AC-AC system is proposed as an effective replacement for the conventional AC-DC-AC system which employs a two-step power conversion.Comment: 11 page

Control of wind energy conversion systems based on the Modular Multilevel Matrix converter

The nominal power of single Wind Energy Conversion Systems (WECS) has been steadily growing, reaching power ratings close to 10MW. In the power conversion stage, medium-voltage power converters are replacing the conventional low-voltage back-to-back topology. Modular Multilevel Converters have appeared as a promising solution for Multi-MW WECSs, due to their modularity, and the capability to reach high nominal voltages. This paper discusses the application of the Modular Multilevel Matrix Converter (M3C) to drive MultiMW WECSs. The modelling and control systems required for this application are extensively analysed and discussed in this paper. The proposed control strategies enable decoupled operation of the converter, providing maximum power point tracking (MPPT) capability at the generator-side, grid code compliance at the grid-side [including Low Voltage Ride Through Control (LVRT)], and good steady state and dynamic performance for balancing the capacitor voltages in all the clusters. Finally, the effectiveness of the proposed control strategy is validated through simulations and experimental results conducted with a 27 power-cell prototype

A Novel Control Method For Grid Side Inverters Under Generalized Unbalanced Operating Conditions

This thesis provides a summary on renewable energy sources integration into the grid, using an inverter, along with a comprehensive literature research on variety of available control methods. A new generalized method for grid side inverter control under unbalanced operating conditions is also proposed. The presented control method provides complete harmonic elimination in line currents and DC link voltage with adjustable power factor. The method is general, and can be used for all levels of imbalance in grid voltages and line impedances. The control algorithm proposed in this work has been implemented by using MATLAB Simulink and dSPACE RT1104 control system. Simulation and experimental results presented in this thesis are in excellent agreement

Flexible operation of grid-interfacing converters in distribution networks : bottom-up solutions to voltage quality enhancement

Due to the emerging application of distributed generation (DG), large numbers of DG systems are expected to deliver electricity into the distribution network in the near future. For the most part these systems are not ready for riding through grid disturbances and cannot mitigate unwanted influences on the grid. On the one hand, with the increasing use of sensitive and critical equipment by customers, the electricity network is required to serve high voltage quality. On the other hand, more and more unbalanced and nonlinear equipment, including DG units, is negatively affecting the power quality of distribution networks. To adapt to the future distribution network, the tendency for grid-interfacing converters will be to integrate voltage quality enhancement with DG functionality. In this thesis, the flexible operation of grid-interfacing converters in distribution networks is investigated for the purpose of voltage quality enhancement at both the grid and user sides. The research is carried out in a bottom-up fashion, from the low-level power electronics control, through the realization of individual system functionality, finally arriving at system-level concepts and implementation. Being essential to the control of grid-interfacing converters, both stationaryframe techniques for voltage detection and synchronization in disturbed grids, and asymmetrical current regulation are investigated. Firstly, a group of high performance filters for the detection of fundamental symmetrical sequences and harmonics under various grid conditions is proposed. The robustness of the proposed filters to small grid-frequency variation and their adaptability to large frequency change are discussed. Secondly, multiple reference frame current regulation is explored for dealing with unbalanced grid conditions. As a complement to the existing proportional resonant (PR) controllers, sequence-decoupled resonant (SDR) controllers are proposed for regulating individual symmetric sequences. Based on the modeling of a four-leg grid-connected system in different reference frames, three types of controllers, i.e. PI, PR, and proportional plus SDR controllers are compared. Grid-interactive control of distributed power generation, i.e. voltage unbalance compensation, grid-fault ride-through control and flexible power transfer, as well as the modeling of harmonic interaction, are all investigated. The in-depth study and analysis of these grid interactions show the grid-support possibilities and potential negative impact on the grid of inverter-based DG units, beyond their primary goal of power delivery. In order to achieve a co-operative voltage unbalance compensation based on distributed DG systems, two control schemes, namely voltage unbalance factor based control and negative-sequence admittance control, are proposed. The negativesequence voltages at the grid connection point can be compensated and mitigated by regulating the negative-sequence currents flowing between the grid and DG converters. Flexible active and reactive power control during unbalanced voltage dips is proposed that enables DG systems to enhance grid-fault ride-through capability and to adapt to various requirements for grid voltage support. By changing adaptable weighting factors, the compensation of oscillating power and the regulation of grid currents can be easily implemented. Two joint strategies for the simultaneous control of active and reactive power are derived, which maintain the adaptive controllability that can cope with multiple constraints in practical applications. The contribution of zero-sequence currents to active power control is also analyzed as a complement to the proposed control, which is based on positive- and negative-sequence components. Harmonic interaction between DG inverters and the grid is modeled and analyzed with an impedance-based approach. In order to mitigate the harmonic distortion in a polluted grid, it is proposed to specify output impedance limits as a design constraint for DG inverters. Results obtained from modeling, analysis, and simulations of a distribution network with aggregated DG inverters, show that the proposed method is a simple and effective way for estimating harmonic quasi-resonance problems. By integrating these proposed control strategies in a modified conventional series-parallel structure, we arrived at a group of grid-interfacing system topologies that is suitable for DG applications, voltage quality improvement, and flexible power transfer. A concrete laboratory system details the proposed concepts and specifies the practical problems related to control design. The introduction of multi-level control objectives illustrates that the proposed system can ride through voltage disturbances, can enhance the grid locally, and can continue the power transfer to and from the grid while high voltage quality is maintained for the local loads within the system module. A dual-converter laboratory set-up was built, with which the proposed concepts and practical implementation have been fully demonstrated

Design and Development of Novel Matrix Converter Performance Enhancement Technique for Induction Motor Drive

Matrix converter is a direct AC-AC converter topology that directly converts energy from an AC source to an AC load without the need of a bulky and limited lifetime energy storage element. Due to the significant advantages offered by matrix converter, such as adjustable power factor, capability of regeneration and high quality sinusoidal input/output waveforms. Matrix converter has been one of the AC–AC topologies that hasreceived extensive research attention for being an alternative to replace traditional AC-DC-AC converters in the variable voltage and variable frequency AC drive applications. In the present paper an indirect space vector modulated matrix converter is proposed. The basic idea of an indirect modulation scheme is to separately apply SVM to the rectification and inversion stages, before combining their switching states to produce the final gating signals. The paper encompasses development of a laboratory prototype of 230V, 250VA three phase to three phase DSP controlled matrix converter fed induction motor drive. The observations and real time testings have been carried out to evaluate and improve the stability of system under various typical abnormal input voltage condition

Contributions to the multi-frequency control of gridtied voltage source converters

El interés por la producción de energía limpia está en aumento y la generación de este tipo de energía se puede fomentar mediante la instalación de generadores locales. Dichos generadores son conectados a la red de distribución a través de convertidores de potencia. Al mismo tiempo el número de cargas conectadas a la red está incrementando y con ello el número de cargas no lineales. Estas últimas consumen corrientes armónicas y esto provoca distorsión armónica a la red. En esta tesis se estudia y se presentan contribuciones en el control de los convertidores de potencia para que al mismo tiempo que se inyecta potencia, el convertidor sea capaz de actuar adecuadamente frente a la distorsión armónica del voltaje de la red (control multifrecuencial). En primer lugar, esta tesis cubrirá el estudio de las diferentes técnicas de control de corrientes armónicas y también de las diferentes técnicas de sincronización y detección de componentes armónicas de tensión presentes en la red. En cuanto al cálculo de referencias de corrientes armónicas, se explican las principales variantes dependiendo de la funcionalidad deseada y se estudia la entrega de potencia instantánea constante incluso con red distorsionada. Además, se propone un nuevo método de cálculo para eliminar las principales oscilaciones de potencia sin exceder las limitaciones de distorsión de corrientes. También se describen las limitaciones del convertidor cuando se trabaja con componentes fundamentales y armónicas. Se analizan los principales saturadores multifrecuenciales para evitar la sobremodulación y se propone un nuevo saturador que no empeora la dinámica total del sistema y siempre consigue el mínimo THD de corriente. Por último, se aborda la problemática de la distorsión armónica del voltaje de red. Primero se estudia la compensación de las corrientes consumidas por cargas locales y después se propone la compensación directa de la tensión del PCC. En esta tesis se intenta incrementar el número de funcionalidades que puede desempeñar el convertidor para que además de entregar potencia, sea capaz de mejorar la calidad de la red, sin exceder las limitaciones físicas del convertidor. Cada una de las contribuciones es validada mediante resultados de simulación y experimentales

Control of Asymmetric Permanent Magnet Synchronous Generator Systems

The thesis focuses on the control of asymmetric permanent magnet synchronous generator (PMSG) system, with particular reference to the suppression of its second harmonic (2h) power, DC bus voltage and torque ripples. The asymmetries include the unbalanced resistances, unbalanced inductances, and unbalanced 3-phase back-electromotive forces (EMFs). The mathematical model of the general asymmetries in the PMSG system is firstly presented. The power ripple and torque ripple due to the asymmetries without/with negative-(N-) sequence currents are then analysed in detail. It shows that there are 2h impedances in the synchronous dq-axis frame. Consequently, the N-sequence currents emerge under the conventional current proportional and integral (PI) control, which will result in undesired 2h power, DC bus voltage and torque ripples. To suppress the 2h torque resulted from the N-sequence currents, three typical methods aiming for balanced currents without N-sequence currents are reviewed, evaluated and their relationship is revealed. It shows that all these three methods are capable of suppressing the N-sequence currents as verified by experiments. However, the 2h power and DC bus voltage cannot be suppressed. To suppress the undesired 2h power and DC bus voltage, an improved power control without any sequential component decomposers under general unbalanced conditions is proposed. Its effectiveness is validated by elaborated experiments on a prototype PMSG with inherent asymmetry and deliberately introduced asymmetries. However, the 2h torque is compromised. To solve the 2h torque, power and DC bus voltage simultaneously, the compensation in parallel with the DC bus is investigated in the PMSG system with asymmetric impedances. The undesired 2h power from the PMSG is compensated by the 2h power from the compensation unit. Two topologies of the compensation unit and corresponding control methods are investigated, while the compensation effectiveness is validated by experiments. Furthermore, the compensation unit with external circuits in series with the asymmetric PMSG is investigated. By the compensation in series, the original unbalanced system is modified to a balanced system in theory. Therefore, the N-sequence currents, 2h power, DC bus voltage, and torque ripple can be naturally suppressed. The feasibility of this compensation method is verified by experiments at different speeds and load conditions, although the effectiveness may be slightly affected by the non-linearity of the compensation inductors in practice. Finally, the research of suppressing the 2h DC bus voltage and torque ripple is extended to the dual 3-phase PMSG system with one channel failed. By utilizing the windings, rectifier or inverter in the faulty channel which are still functional, three methods designated as two sets in parallel, two DC buses in parallel and N-sequence currents compensation are investigated, which require minimum extra hardware investment compared with the compensation in parallel and in series

Unified Power Quality Conditioner for Grid Integration of Wind Generators

A Unified Power Quality Conditioner (UPQC) is relatively a new member of the custom power device family. It is a comprehensive custom power device, with integrated shunt and series active filters. The cost of the device, which is higher than other custom power/FACTS devices, because of twin inverter structure and control complexity, will have to be justified by exploring new areas of application where the cost of saving power quality events outweighs the initial cost of installation. Distributed generation (such as wind generation) is one field where the UPQC can find its potential application. There has been a considerable increase in the power generation from wind farms. This has created the necessity for wind farms connectivity with the grid during power system faults, voltage sags and frequency variations. The application of active filters/custom power devices in the field of wind generation to provide reactive power compensation, additional fault ride through capability and to maintain Power Quality (PQ) at the point of common coupling is gaining popularity. Wind generation like other forms of distributed generation often relies on power electronics technology for flexible interconnection to the power grid. The application of power electronics in wind generation has resulted in improved power quality and increased energy capture. The rapid development in power electronics, which has resulted in high kVA rating of the devices and low price per kVA, encourages the application of such devices at distribution level. This work focuses on development of a laboratory prototype of a UPQC, and investigation of its application for the flexible grid integration of fixed and variable speed wind generators through dynamic simulation studies. A DSP based fully digital controller and interfacing hardware has been developed for a 24 kVA (12 kVA-shunt compensator and 12 kVA-series compensator) laboratory prototype of UPQC. The modular control approach facilitates the operation of the device either as individual series or shunt compensator or as a UPQC. Different laboratory tests have been carried out to demonstrate the effectiveness of developed control schemes.A simulation-based analysis is carried out to investigate the suitability of application of a UPQC to achieve Irish grid code compliance of a 2 MW Fixed Speed Induction Generator (FSIG). The rating requirement of the UPQC for the wind generation application has been investigated. A general principle is proposed to choose the practical and economical rating of the UPQC for this type of application. A concept of UPQC integrated Wind Generator (UPQC-WG) has been proposed. The UPQC-WG is a doubly fed induction machine with converters integrated in the stator and rotor circuits and is capable of adjustable speed operation. The operation of UPQC-WG under sub and super-synchronous speed range has been demonstrated. The Irish grid code compliance of the same has been demonstrated with a detailed dynamic simulation

Advance control of multilevel converters for integration of distributed generation resources into ac grid

Premi extraordinari doctorat curs 2011-2012, àmbit d’Enginyeria IndustrialDistributed generation (DG) with a converter interface to the power grid is found in many of the green power resources applications. This dissertation describes a multi-objective control technique of voltage source converter (VSC) based on multilevel converter topologies, for integration of DG resources based on renewable energy (and non-renewable energy)to the power grid. The aims have been set to maintain a stable operation of the power grid, in case of di erent types of grid-connected loads. The proposed method provides compensation for active, reactive, and harmonic load current components. A proportional-integral (PI) control law is derived through linearization of the inherently non-linear DG system model, so that the tasks of current control dynamics and dc capacitor voltage dynamics become decoupled. This decoupling allows us to control the DG output currents and the dc bus voltage independently of each other, thereby providing either one of these decoupled subsystems a dynamic response that signi cantly slower than that of the other. To overcome the drawbacks of the conventional method, a computational control delay compensation method, which delaylessly and accurately generates the DG reference currents, is proposed. The rst step is to extract the DG reference currents from the sensed load currents by applying the stationary reference frame and then transferred into synchronous reference frame method, and then, the reference currents are modi ed, so that the delay will be compensated. The transformed variables are used in control of the multilevel voltage source converter as the heart of the interfacing system between DG resources and power grid. By setting appropriate compensation current references from the sensed load currents in control circuit loop of DG link, the active, reactive, and harmonic load current components will be compensated with fast dynamic response, thereby achieving sinusoidal grid currents in phase with load voltages while required power of loads is more than the maximum injected power of the DG resources. The converter, which is controlled by the described control strategy, guarantees maximum injection of active power to the grid continuously, unity displacement power factor of power grid, and reduced harmonic load currents in the common coupling point. In addition, high current overshoot does not exist during connection of DG link to the power grid, and the proposed integration strategy is insensitive to grid overload.La Generació Distribuïda (DG) injectada a la xarxa amb un convertidor estàtic és una solució molt freqüent en l'ús de molts dels recursos renovables. Aquesta tesis descriu una técnica de control multi-objectiu del convertidor en font de tensió (VSC), basat en les topologies de convertidor multinivell, per a la integració de les fonts distribuïdes basades en energies renovables i també de no renovables.Els objectius fixats van encaminats a mantenir un funcionament estable de la xarxa elèctrica en el cas de la connexió de diferents tipus de càrregues. El mètode de control proposat ofereix la possibilitat de compensació de les components actives i reactives de la potencia, i les components harmòniques del corrent consumit per les càrregues.La llei de control proporcional-Integral (PI) s’obté de la linearització del model inherentment no lineal del sistema, de forma que el problema de control del corrent injectat i de la tensió d’entrada del convertidor queden desacoblats. Aquest desacoblament permet el control dels corrents de sortida i la tensió del bus de forma independent, però amb un d’ells amb una dinàmica inferior.Per superar els inconvenients del mètode convencional, s’usa un retard computacional, que genera les senyals de referència de forma acurada i sense retard. El primer pas es calcular els corrents de referència a partir de les mesures de corrent. Aquest càlcul es fa primer transformant les mesures a la referència estacionaria per després transformar aquests valors a la referència síncrona. En aquest punt es on es poden compensar els retards.Les variables transformades son usades en els llaços de control del convertidor multinivell. Mitjançant aquests llaços de control i les referències adequades, el convertidor és capaç de compensar la potencia activa, reactiva i els corrents harmònics de la càrrega amb una elevada resposta dinàmica, obtenint uns corrents de la xarxa de forma completament sinusoïdal, i en fase amb les tensions.El convertidor, controlat amb el mètode descrit, garanteix la màxima injecció de la potencia activa, la injecció de la potencia reactiva per compensar el factor de potencia de la càrrega, i la reducció de les components harmòniques dels corrents consumits per la càrrega. A més, garanteix una connexió suau entre la font d’energia i la xarxa. El sistema proposat es insensible en front de la sobrecarrega de la xarxaAward-winningPostprint (published version