19 research outputs found

    Energy-Efficient Receiver Design for High-Speed Interconnects

    Get PDF
    High-speed interconnects are of vital importance to the operation of high-performance computing and communication systems, determining the ultimate bandwidth or data rates at which the information can be exchanged. Optical interconnects and the employment of high-order modulation formats are considered as the solutions to fulfilling the envisioned speed and power efficiency of future interconnects. One common key factor in bringing the success is the availability of energy-efficient receivers with superior sensitivity. To enhance the receiver sensitivity, improvement in the signal-to-noise ratio (SNR) of the front-end circuits, or equalization that mitigates the detrimental inter-symbol interference (ISI) is required. In this dissertation, architectural and circuit-level energy-efficient techniques serving these goals are presented. First, an avalanche photodetector (APD)-based optical receiver is described, which utilizes non-return-to-zero (NRZ) modulation and is applicable to burst-mode operation. For the purposes of improving the overall optical link energy efficiency as well as the link bandwidth, this optical receiver is designed to achieve high sensitivity and high reconfiguration speed. The high sensitivity is enabled by optimizing the SNR at the front-end through adjusting the APD responsivity via its reverse bias voltage, along with the incorporation of 2-tap feedforward equalization (FFE) and 2-tap decision feedback equalization (DFE) implemented in current-integrating fashion. The high reconfiguration speed is empowered by the proposed integrating dc and amplitude comparators, which eliminate the RC settling time constraints. The receiver circuits, excluding the APD die, are fabricated in 28-nm CMOS technology. The optical receiver achieves bit-error-rate (BER) better than 1E−12 at −16-dBm optical modulation amplitude (OMA), 2.24-ns reconfiguration time with 5-dB dynamic range, and 1.37-pJ/b energy efficiency at 25 Gb/s. Second, a 4-level pulse amplitude modulation (PAM4) wireline receiver is described, which incorporates continuous time linear equalizers (CTLEs) and a 2-tap direct DFE dedicated to the compensation for the first and second post-cursor ISI. The direct DFE in a PAM4 receiver (PAM4-DFE) is made possible by the proposed CMOS track-and-regenerate slicer. This proposed slicer offers rail-to-rail digital feedback signals with significantly improved clock-to-Q delay performance. The reduced slicer delay relaxes the settling time constraint of the summer circuits and allows the stringent DFE timing constraint to be satisfied. With the availability of a direct DFE employing the proposed slicer, inductor-based bandwidth enhancement and loop-unrolling techniques, which can be power/area intensive, are not required. Fabricated in 28-nm CMOS technology, the PAM4 receiver achieves BER better than 1E−12 and 1.1-pJ/b energy efficiency at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist frequency. Third, digital neural-network-enhanced FFEs (NN-FFEs) for PAM4 analog-to-digital converter (ADC)-based optical interconnects are described. The proposed NN-FFEs employ a custom learnable piecewise linear (PWL) activation function to tackle the nonlinearities with short memory lengths. In contrast to the conventional Volterra equalizers where multipliers are utilized to generate the nonlinear terms, the proposed NN-FFEs leverage the custom PWL activation function for nonlinear operations and reduce the required number of multipliers, thereby improving the area and power efficiencies. Applications in the optical interconnects based on micro-ring modulators (MRMs) are demonstrated with simulation results of 50-Gb/s and 100-Gb/s links adopting PAM4 signaling. The proposed NN-FFEs and the conventional Volterra equalizers are synthesized with the standard-cell libraries in a commercial 28-nm CMOS technology, and their power consumptions and performance are compared. Better than 37% lower power overhead can be achieved by employing the proposed NN-FFEs, in comparison with the Volterra equalizer that leads to similar improvement in the symbol-error-rate (SER) performance.</p

    Arquiteturas paralelas avançadas para transmissores 5G totalmente digitais

    Get PDF
    The fifth generation of mobile communications (5G) is being prepared and should be rolled out in the early coming years. Massive number of Radio-Frequency (RF) front-ends, peak data rates of 10 Gbps (everywhere and everytime), latencies lower than 10 msec and huge device densities are some of the expected disruptive capabilities. At the same time, previous generations can not be jeopardized, fostering the design of novel flexible and highly integrated radio transceivers able to support the simultaneous transmission of multi-band and multi-standard signals. The concept of all-digital transmission is being pointed out as a promising architecture to cope with such challenging requirements, due to its fully digital radio datapath. This thesis is focused on the proposal and validation of fully integrated and advanced digital transmitter architectures that excel the state-of-the-art in different figures of merit, such as transmission bandwidth, spectral purity, carrier agility, flexibility, and multi-band capability. The first part of this thesis introduces the concept of all-digital RF transmission. In particular, the foundations inherent to this thematic line are given, together with the recent advances reported in the state-of-the-art architectures.The core of this thesis, containing the main developments achieved during the Ph.D. work, is then presented and discussed. The first key contribution to the state-of-the-art is the use of cascaded Delta-Sigma (∆Σ) architectures to relax the analog filtering requirements of the conventional All-Digital Transmitters while maintaining the constant envelope waveform. Then, it is presented the first reported architecture where Antenna Arrays are directly driven by single-chip and single-bit All-Digital Transmitters, with promising results in terms of simplification of the RF front-ends and overall flexibility. Subsequently, the thesis proposes the first reported RF-stage All-Digital Transmitter that can be embedded within a single Field-Programmable Gate Array (FPGA) device. Thereupon, novel techniques to enable the design of wideband All-Digital Transmitters are reported. Finally, the design of concurrent multi-band transmitters is introduced. In particular, the design of agile and flexible dual and triple bands All-DigitalTransmitter (ADT) is demonstrated, which is a very important topic for scenarios that demand carrier aggregation. This Ph.D. contributes withseveral advances to the state-of-the-art of RF all-digital transmitters.A quinta geração de comunicações móveis (5G) está a ser preparada e deve ser comercializada nos próximos anos. Algumas das caracterı́sticas inovadoras esperadas passam pelo uso de um número massivo de font-ends de Rádio-Frequência (RF), taxas de pico de transmissão de dados de 10 Gbps (em todos os lugares e em todas as ocasiões), latências inferiores a 10 mseg e elevadas densidades de dispositivos. Ao mesmo tempo, as gerações anteriores não podem ser ignoradas, fomentando o design de novos transceptores de rádio flexı́veis e altamente integrados, capazes de suportar a transmissão simultânea de sinais multi-banda e multi-standard. O conceito de transmissão totalmente digital é considerado como um tipo de arquitetura promissora para lidar com esses requisitos desafiantes, devido ao seu datapath de rádio totalmente digital. Esta tese é focada na proposta e validação de arquiteturas de transmissores digitais totalmente integradas e avançadas que ultrapassam o estado da arte em diferentes figuras de mérito, como largura de banda de transmissão, pureza espectral, agilidade de portadora, flexibilidade e capacidade multibanda. A primeira parte desta tese introduz o conceito de transmissores de RF totalmente digitais. Em particular, os fundamentos inerentes a esta linha temática são apresentados, juntamente com os avanços mais recentes do estado-da-arte. O núcleo desta tese, contendo os principais desenvolvimentos alcançados durante o trabalho de doutoramento, é então apresentado e discutido. A primeira contribuição fundamental para o estado da arte é o uso de arquiteturas em cascata com moduladores ∆Σ para relaxar os requisitos de filtragem analógica dos transmissores RF totalmente digitais convencionais, mantendo a forma de onda envolvente constante. Em seguida, é apresentada a primeira arquitetura em que agregados de antenas são excitados diretamente por transmissores digitais de um único bit inseridos num único chip, com resultados promissores em termos de simplificação dos front-ends de RF e flexibilidade em geral. Posteriormente, é proposto o primeiro transmissor totalmente digital RF-stage relatado que pode ser incorporado dentro de um único Agregado de Células Lógicas Programáveis. Novas técnicas para permitir o desenho de transmissores RF totalmente digitais de banda larga são também apresentadas. Finalmente, o desenho de transmissores simultâneos de múltiplas bandas é exposto. Em particular, é demonstrado o desenho de transmissores de duas e três bandas ágeis e flexı́veis, que é um tópico essencial para cenários que exigem agregação de múltiplas bandas.Apoio financeiro da Fundação para a Ciência e Tecnologia (FCT) no âmbito de uma bolsa de doutoramento, ref. PD/BD/105857/2014.Programa Doutoral em Telecomunicaçõe

    Photonic and Electronic Co-integration for Millimetre-Wave Hybrid Photonic-Wireless Links

    Get PDF

    Photonic and Electronic Co-integration for Millimetre-Wave Hybrid Photonic-Wireless Links

    Get PDF

    Modeling EMI Resulting from a Signal Via Transition Through Power/Ground Layers

    Get PDF
    Signal transitioning through layers on vias are very common in multi-layer printed circuit board (PCB) design. For a signal via transitioning through the internal power and ground planes, the return current must switch from one reference plane to another reference plane. The discontinuity of the return current at the via excites the power and ground planes, and results in noise on the power bus that can lead to signal integrity, as well as EMI problems. Numerical methods, such as the finite-difference time-domain (FDTD), Moment of Methods (MoM), and partial element equivalent circuit (PEEC) method, were employed herein to study this problem. The modeled results are supported by measurements. In addition, a common EMI mitigation approach of adding a decoupling capacitor was investigated with the FDTD method

    Thrust Area Report, Engineering Research, Development and Technology

    Full text link
    corecore