Contactless Test Access Mechanism for 3D IC

3D IC integration presents many advantages over the current 2D IC integration. It has the potential to reduce the power consumption and the physical size while supporting higher bandwidth and processing speed. Through Silicon Via’s (TSVs) are vertical interconnects between different layers of 3D ICs with a typical 5μm diameter and 50μm length. To test a 3D IC, an access mechanism is needed to apply test vectors to TSVs and observe their responses. However, TSVs are too small for access by current wafer probes and direct TSV probing may affect their physical integrity. In addition, the probe needles for direct TSV probing must be cleaned or replaced frequently. Contactless probing method resolves most of the TSV probing problems and can be employed for small-pitch TSVs. In this dissertation, contactless test access mechanisms for 3D IC have been explored using capacitive and inductive coupling techniques. Circuit models for capacitive and inductive communication links are extracted using 3D full-wave simulations and then circuit level simulations are carried out using Advanced Design System (ADS) design environment to verify the results. The effects of cross-talk and misalignment on the communication link have been investigated. A contactless TSV probing method using capacitive coupling is proposed and simulated. A prototype was fabricated using TSMC 65nm CMOS technology to verify the proposed method. The measurement results on the fabricated prototype show that this TSV probing scheme presents -55dB insertion loss at 1GHz frequency and maintains higher than 35dB signal-to-noise ratio within 5µm distance. A microscale contactless probe based on the principle of resonant inductive coupling has also been designed and simulated. Experimental measurements on a prototype fabricated in TSMC 65nm CMOS technology indicate that the data signal on the TSV can be reconstructed when the distance between the TSV and the probe remains less than 15µm

Overcoming the Challenges for Multichip Integration: A Wireless Interconnect Approach

The physical limitations in the area, power density, and yield restrict the scalability of the single-chip multicore system to a relatively small number of cores. Instead of having a large chip, aggregating multiple smaller chips can overcome these physical limitations. Combining multiple dies can be done either by stacking vertically or by placing side-by-side on the same substrate within a single package. However, in order to be widely accepted, both multichip integration techniques need to overcome significant challenges. In the horizontally integrated multichip system, traditional inter-chip I/O does not scale well with technology scaling due to limitations of the pitch. Moreover, to transfer data between cores or memory components from one chip to another, state-of-the-art inter-chip communication over wireline channels require data signals to travel from internal nets to the peripheral I/O ports and then get routed over the inter-chip channels to the I/O port of the destination chip. Following this, the data is finally routed from the I/O to internal nets of the target chip over a wireline interconnect fabric. This multi-hop communication increases energy consumption while decreasing data bandwidth in a multichip system. On the other hand, in vertically integrated multichip system, the high power density resulting from the placement of computational components on top of each other aggravates the thermal issues of the chip leading to degraded performance and reduced reliability. Liquid cooling through microfluidic channels can provide cooling capabilities required for effective management of chip temperatures in vertical integration. However, to reduce the mechanical stresses and at the same time, to ensure temperature uniformity and adequate cooling competencies, the height and width of the microchannels need to be increased. This limits the area available to route Through-Silicon-Vias (TSVs) across the cooling layers and make the co-existence and co-design of TSVs and microchannels extreamly challenging. Research in recent years has demonstrated that on-chip and off-chip wireless interconnects are capable of establishing radio communications within as well as between multiple chips. The primary goal of this dissertation is to propose design principals targeting both horizontally and vertically integrated multichip system to provide high bandwidth, low latency, and energy efficient data communication by utilizing mm-wave wireless interconnects. The proposed solution has two parts: the first part proposes design methodology of a seamless hybrid wired and wireless interconnection network for the horizontally integrated multichip system to enable direct chip-to-chip communication between internal cores. Whereas the second part proposes a Wireless Network-on-Chip (WiNoC) architecture for the vertically integrated multichip system to realize data communication across interlayer microfluidic coolers eliminating the need to place and route signal TSVs through the cooling layers. The integration of wireless interconnect will significantly reduce the complexity of the co-design of TSV based interconnects and microchannel based interlayer cooling. Finally, this dissertation presents a combined trade-off evaluation of such wireless integration system in both horizontal and vertical sense and provides future directions for the design of the multichip system

A DLL Based Test Solution for 3D ICs

Integrated circuits (ICs) are rapidly changing and vertical integration and packaging strategies have already become an important research topic. 2.5D and 3D IC integrations have obvious advantages over the conventional two dimensional IC implementations in performance, capacity, and power consumption. A passive Si interposer utilizing Through-Silicon via (TSV) technology is used for 2.5D IC integration. TSV is also the enabling technology for 3D IC integration. TSV manufacturing defects can affect the performance of stacked devices and reduce the yield. Manufacturing test methodologies for TSVs have to be developed to ensure fault-free devices. This thesis presents two test methods for TSVs in 2.5D and 3D ICs utilizing Delay-Locked Loop (DLL) modules. In the test method developed for TSVs in 2.5D ICs, a DLL is used to determine the propagation delay for fault detection. TSV faults in 3D ICs are detected through observation of the control voltage of a DLL. The proposed test methods present a robust performance against Process, supply Voltage and Temperature (PVT) variations due to the inherent feedback of DLLs. 3D full-wave simulations are performed to extract circuit level models for TSVs and fragments of an interposer wires using HFSS simulation tools. The extracted TSV models are then used to perform circuit level simulations using ADS tools from Agilent. Simulation results indicate that the proposed test solution for TSVs can detect manufacturing defects affecting the TSV propagation delay

High Speed Test Interface Module Using MEMS Technology

With the transient frequency of available CMOS technologies exceeding hundreds of gigahertz and the increasing complexity of Integrated Circuit (IC) designs, it is now apparent that the architecture of current testers needs to be greatly improved to keep up with the formidable challenges ahead. Test requirements for modern integrated circuits are becoming more stringent, complex and costly. These requirements include an increasing number of test channels, higher test-speeds and enhanced measurement accuracy and resolution. In a conventional test configuration, the signal path from Automatic Test Equipment (ATE) to the Device-Under-Test (DUT) includes long traces of wires. At frequencies above a few gigahertz, testing integrated circuits becomes a challenging task. The effects on transmission lines become critical requiring impedance matching to minimize signal reflection. AC resistance due to the skin effect and electromagnetic coupling caused by radiation can also become important factors affecting the test results. In the design of a Device Interface Board (DIB), the greater the physical separation of the DUT and the ATE pin electronics, the greater the distortion and signal degradation. In this work, a new Test Interface Module (TIM) based on MEMS technology is proposed to reduce the distance between the tester and device-under-test by orders of magnitude. The proposed solution increases the bandwidth of test channels and reduces the undesired effects of transmission lines on the test results. The MEMS test interface includes a fixed socket and a removable socket. The removable socket incorporates MEMS contact springs to provide temporary with the DUT pads and the fixed socket contains a bed of micro-pins to establish electrical connections with the ATE pin electronics. The MEMS based contact springs have been modified to implement a high-density wafer level test probes for Through Silicon Vias (TSVs) in three dimensional integrated circuits (3D-IC). Prototypes have been fabricated using Silicon On Insulator SOI wafer. Experimental results indicate that the proposed architectures can operate up to 50 GHz without much loss or distortion. The MEMS probes can also maintain a good elastic performance without any damage or deformation in the test phase

Design-for-Test and Test Optimization Techniques for TSV-based 3D Stacked ICs

<p>As integrated circuits (ICs) continue to scale to smaller dimensions, long interconnects</p><p>have become the dominant contributor to circuit delay and a significant component of</p><p>power consumption. In order to reduce the length of these interconnects, 3D integration</p><p>and 3D stacked ICs (3D SICs) are active areas of research in both academia and industry.</p><p>3D SICs not only have the potential to reduce average interconnect length and alleviate</p><p>many of the problems caused by long global interconnects, but they can offer greater design</p><p>flexibility over 2D ICs, significant reductions in power consumption and footprint in</p><p>an era of mobile applications, increased on-chip data bandwidth through delay reduction,</p><p>and improved heterogeneous integration.</p><p>Compared to 2D ICs, the manufacture and test of 3D ICs is significantly more complex.</p><p>Through-silicon vias (TSVs), which constitute the dense vertical interconnects in a</p><p>die stack, are a source of additional and unique defects not seen before in ICs. At the same</p><p>time, testing these TSVs, especially before die stacking, is recognized as a major challenge.</p><p>The testing of a 3D stack is constrained by limited test access, test pin availability,</p><p>power, and thermal constraints. Therefore, efficient and optimized test architectures are</p><p>needed to ensure that pre-bond, partial, and complete stack testing are not prohibitively</p><p>expensive.</p><p>Methods of testing TSVs prior to bonding continue to be a difficult problem due to test</p><p>access and testability issues. Although some built-in self-test (BIST) techniques have been</p><p>proposed, these techniques have numerous drawbacks that render them impractical. In this dissertation, a low-cost test architecture is introduced to enable pre-bond TSV test through</p><p>TSV probing. This has the benefit of not needing large analog test components on the die,</p><p>which is a significant drawback of many BIST architectures. Coupled with an optimization</p><p>method described in this dissertation to create parallel test groups for TSVs, test time for</p><p>pre-bond TSV tests can be significantly reduced. The pre-bond probing methodology is</p><p>expanded upon to allow for pre-bond scan test as well, to enable both pre-bond TSV and</p><p>structural test to bring pre-bond known-good-die (KGD) test under a single test paradigm.</p><p>The addition of boundary registers on functional TSV paths required for pre-bond</p><p>probing results in an increase in delay on inter-die functional paths. This cost of test</p><p>architecture insertion can be a significant drawback, especially considering that one benefit</p><p>of 3D integration is that critical paths can be partitioned between dies to reduce their delay.</p><p>This dissertation derives a retiming flow that is used to recover the additional delay added</p><p>to TSV paths by test cell insertion.</p><p>Reducing the cost of test for 3D-SICs is crucial considering that more tests are necessary</p><p>during 3D-SIC manufacturing. To reduce test cost, the test architecture and test</p><p>scheduling for the stack must be optimized to reduce test time across all necessary test</p><p>insertions. This dissertation examines three paradigms for 3D integration - hard dies, firm</p><p>dies, and soft dies, that give varying degrees of control over 2D test architectures on each</p><p>die while optimizing the 3D test architecture. Integer linear programming models are developed</p><p>to provide an optimal 3D test architecture and test schedule for the dies in the 3D</p><p>stack considering any or all post-bond test insertions. Results show that the ILP models</p><p>outperform other optimization methods across a range of 3D benchmark circuits.</p><p>In summary, this dissertation targets testing and design-for-test (DFT) of 3D SICs.</p><p>The proposed techniques enable pre-bond TSV and structural test while maintaining a</p><p>relatively low test cost. Future work will continue to enable testing of 3D SICs to move</p><p>industry closer to realizing the true potential of 3D integration.</p>Dissertatio

Wireless Testing of Integrated Circuits.

Integrated circuits (ICs) are usually tested during manufacture by means of automatic testing equipment (ATE) employing probe cards and needles that make repeated physical contact with the ICs under test. Such direct-contact probing is very costly and imposes limitations on the use of ATE. For example, the probe needles must be frequently cleaned or replaced, and some emerging technologies such as three-dimensional ICs cannot be probed at all. As an alternative to conventional probe-card testing, wireless testing has been proposed. It mitigates many of the foregoing problems by replacing probe needles and contact points with wireless communication circuits. However, wireless testing also raises new problems which are poorly understood such as: What is the most suitable wireless communication technique to employ, and how well does it work in practice? This dissertation addresses the design and implementation of circuits to support wireless testing of ICs. Various wireless testing methods are investigated and evaluated with respect to their practicality. The research focuses on near-field capacitive communication because of its efficiency over the very short ranges needed during IC manufacture. A new capacitive channel model including chip separation, cross-talk, and misalignment effects is proposed and validated using electro-magnetic simulation studies to provide the intuitions for efficient antenna and circuit design. We propose a compact clock and data recovery architecture to avoid a dedicated clock channel. An analytical model which predicts the DC-level fluctuation due to the capacitive channel is presented. Based on this model, feed-forward clock selection is designed to enhance performance. A method to select proper channel termination is discussed to maximize the channel efficiency for return-to-zero signaling. Two prototype ICs incorporating wireless testing systems were fabricated and tested with the proposed methods of testing digital circuits. Both successfully demonstrated gigahertz communication speeds with a bit-error rate less than 10^−11. A third prototype IC containing analog voltage measurement circuits was implemented to determine the feasibility of wirelessly testing analog circuits. The fabricated prototype achieved satisfactory voltage measurement with 1 mV resolution. Our work demonstrates the validity of the proposed models and the feasibility of near-field capacitive communication for wireless testing of ICs.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/93993/1/duelee_1.pd

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

SOI RF-MEMS Based Variable Attenuator for Millimeter-Wave Applications

The most-attractive feature of microelectromechanical systems (MEMS) technology is that it enables the integration of a whole system on a single chip, leading to positive effects on the performance, reliability and cost. MEMS has made it possible to design IC-compatible radio frequency (RF) devices for wireless and satellite communication systems. Recently, with the advent of 5G, there is a huge market pull towards millimeter-wave devices. Variable attenuators are widely employed for adjusting signal levels in high frequency equipment. RF circuits such as automatic gain control amplifiers, broadband vector modulators, full duplex wireless systems, and radar systems are some of the primary applications of variable attenuators. This thesis describes the development of a millimeter-wave RF MEMS-based variable attenuator implemented by monolithically integrating Coplanar Waveguide (CPW) based hybrid couplers with lateral MEMS varactors on a Silicon–on–Insulator (SOI) substrate. The MEMS varactor features a Chevron type electrothermal actuator that controls the lateral movement of a thick plate, allowing precise change in the capacitive loading on a CPW line leading to a change in isolation between input and output. Electrothermal actuators have been employed in the design instead of electrostatic ones because they can generate relatively larger in-line deflection and force within a small footprint. They also provide the advantage of easy integration with other electrical micro-systems on the same chip, since their fabrication process is compatible with general IC fabrication processes. The development of an efficient and reliable actuator has played an important role in the performance of the proposed design of MEMS variable attenuator. A Thermoreflectance (TR) imaging system is used to acquire the surface temperature profiles of the electrothermal actuator employed in the design, so as to study the temperature distribution, displacement and failure analysis of the Chevron actuator. The 60 GHz variable attenuator was developed using a custom fabrication process on an SOI substrate with a device footprint of 3.8 mm x 3.1 mm. The fabrication process has a high yield due to the high-aspect-ratio single-crystal-silicon structures, which are free from warping, pre-deformation and sticking during the wet etching process. The SOI wafer used has a high resistivity (HR) silicon (Si) handle layer that provides an excellent substrate material for RF communication devices at microwave and millimeter wave frequencies. This low-cost fabrication process provides the flexibility to extend this module and implement more complex RF signal conditioning functions. It is thus an appealing candidate for realizing a wide range of reconfigurable RF devices. The measured RF performance of the 60 GHz variable attenuator shows that the device exhibits attenuation levels (|S21|) ranging from 10 dB to 25 dB over a bandwidth of 4 GHz and a return loss of better than 20 dB. The thesis also presents the design and implementation of a MEMS-based impedance tuner on a Silicon-On-Insulator (SOI) substrate. The tuner is comprised of four varactors monolithically integrated with CPW lines. Chevron actuators control the lateral motion of capacitive thick plates used as contactless lateral MEMS varactors, achieving a capacitance range of 0.19 pF to 0.8 pF. The improvement of the Smith chart coverage is achieved by proper choice of the electrical lengths of the CPW lines and precise control of the lateral motion of the capacitive plates. The measured results demonstrate good impedance matching coverage, with an insertion loss of 2.9 dB. The devices presented in this thesis provide repeatable and reliable operation due to their robust, thick-silicon structures. Therefore, they exhibit relatively low residual stress and are free from stiction and micro-welding problems

Exploration and Design of Power-Efficient Networked Many-Core Systems

Multiprocessing is a promising solution to meet the requirements of near future applications. To get full benefit from parallel processing, a manycore system needs efficient, on-chip communication architecture. Networkon- Chip (NoC) is a general purpose communication concept that offers highthroughput, reduced power consumption, and keeps complexity in check by a regular composition of basic building blocks. This thesis presents power efficient communication approaches for networked many-core systems. We address a range of issues being important for designing power-efficient manycore systems at two different levels: the network-level and the router-level. From the network-level point of view, exploiting state-of-the-art concepts such as Globally Asynchronous Locally Synchronous (GALS), Voltage/ Frequency Island (VFI), and 3D Networks-on-Chip approaches may be a solution to the excessive power consumption demanded by today’s and future many-core systems. To this end, a low-cost 3D NoC architecture, based on high-speed GALS-based vertical channels, is proposed to mitigate high peak temperatures, power densities, and area footprints of vertical interconnects in 3D ICs. To further exploit the beneficial feature of a negligible inter-layer distance of 3D ICs, we propose a novel hybridization scheme for inter-layer communication. In addition, an efficient adaptive routing algorithm is presented which enables congestion-aware and reliable communication for the hybridized NoC architecture. An integrated monitoring and management platform on top of this architecture is also developed in order to implement more scalable power optimization techniques. From the router-level perspective, four design styles for implementing power-efficient reconfigurable interfaces in VFI-based NoC systems are proposed. To enhance the utilization of virtual channel buffers and to manage their power consumption, a partial virtual channel sharing method for NoC routers is devised and implemented. Extensive experiments with synthetic and real benchmarks show significant power savings and mitigated hotspots with similar performance compared to latest NoC architectures. The thesis concludes that careful codesigned elements from different network levels enable considerable power savings for many-core systems.Siirretty Doriast