Bit-Wise Decoders for Coded Modulation and Broadcast Coded Slotted ALOHA

This thesis deals with two aspects of wireless communications. The first aspect is about efficient point-to-point data transmission. To achieve high spectral efficiency, coded modulation, which is a concatenation of higher order modulation with error correction coding, is used. Bit-interleaved coded modulation (BICM) is a pragmatic approach to coded modulation, where soft information on encoded bits is calculated at the receiver and passed to a bit-wise decoder. Soft information is usually obtained in the form of log-likelihood ratios (also known as L-values), calculated using the max-log approximation. In this thesis, we analyze bit-wise decoders for pulse-amplitude modulation (PAM) constellations over the additive white Gaussian noise (AWGN) channel when the max-log approximation is used for calculating L-values. First, we analyze BICM systems from an information theoretic perspective. We prove that the max-log approximation causes information loss for all PAM constellations and labelings with the exception of a symmetric 4-PAM constellation labeled with a Gray code. We then analyze how the max-log approximation affects the generalized mutual information (GMI), which is an achievable rate for a standard BICM decoder. Second, we compare the performance of the standard BICM decoder with that of the ML decoder. We show that, when the signal-to-noise ratio (SNR) goes to infinity, the loss in terms of pairwise error probability is bounded by 1.25 dB for any two codewords. The analysis further shows that the loss is zero for a wide range of linear codes. The second aspect of wireless communications treated in this thesis is multiple channel access. Our main objective here is to provide reliable message exchange between nodes in a wireless ad hoc network with stringent delay constraints. To that end, we propose an uncoordinated medium access control protocol, termed all-to-all broadcast coded slotted ALOHA (B-CSA), that exploits coding over packets at the transmitter side and successive interference cancellation at the receiver side. The protocol resembles low-density parity-check codes and can be analyzed using the theory of codes on graphs. The packet loss rate performance of the protocol exhibits a threshold behavior with distinct error floor and waterfall regions. We derive a tight error floor approximation that is used for the optimization of the protocol. We also show how the error floor approximation can be used to design protocols for networks, where users have different reliability requirements. We use B-CSA in vehicular networks and show that it outperforms carrier sense multiple access currently adopted as the MAC protocol for vehicular communications. Finally, we investigate the possibility of establishing a handshake in vehicular networks by means of B-CSA

Study, analysis and application of Optical OFDM, Single Carrier (SC) and MIMO in Intensity Modulation Direct Detection (IM/DD)

With the rapid growth of wireless data demands and saturation of radio frequency (RF) capacity, visible light communication (VLC) has become a promising candidate to complement conventional RF communication, especially for indoor short range applications. However the performance of the system depends on the propagation and type of system used. An optical Orthogonal Frequency Division Multiplexing (O-OFDM) together with multiple input multiple output (MIMO) in different scenario and modulation techniques are studied in the thesis. A novel optical wireless communication (OWC) multi-cell system with narrow field of view (FOV) is studied. In this system the intensity modulated beam from four light sources are used for communication. The system allows beams to be concentrated in specific areas of the room to serve multiple mobile devices with low interference and hence increase system capacity. The performance of asymmetrically clipped optical orthogonal frequency division multiplexing (ACO-OFDM), direct current biased optical OFDM (DCO-OFDM) and single carrier (SC) modulation are then compared in this system considering single user and multiusers scenarios. The performance of the multi-cell is compared with single cell with wide FOV. It is shown that the capacity for multi-cell system increases with the number of users to 4 times the single user capacity. Also the findings show that multi-cell system with narrow beams can outperform a single wide beam system in terms of coverage area and hence average throughput of about 2.7 times the single wide beam system capacity. One of the impairments in line of sight (LOS) OWC systems is coverage which degrades the performance. A mobile receiver with angular diversity detectors in MIMO channels is studied. The objective is to improve the rank of the channel matrix and hence system throughput. Repetition coding (RC), spatial multiplexing (SMP) and spatial modulation (SM) concepts are used to evaluate throughput across multiple locations in a small room scenario. A novel adaptive spatial modulation (ASM) which is capable of combating channel rank deficiency is devised. Since the receiver is mobile, the channel gains are low in some locations of the room due to the lack of LOS paths between transmitters and receivers. To combat the situation adaptive modulation and per antenna rate control (PARC) is employed to maximise spectral efficiency. The throughputs for fixed transmitters and receivers are compared with the oriented/inclined detectors for different cases. Angular diversity detectors offer a better throughput improvement than the state of the art vertical detectors, for example in ASM angular diversity receiver gives throughput of about 1.6 times that of vertical detectors. Also in SMP the angular detectors offer throughput about 1.4 times that of vertical detectors. SMP gives the best performance compared to RC, SM and ASM, for example SMP gives throughput about 2.5 times that of RC in both vertical detectors and angular diversity receivers. Again SMP gives throughput about 6 times that of SM in both vertical detectors and angular diversity receivers. Also SMP provides throughput about 2 times that of ASM in both vertical detectors and angular diversity receivers. ASM exhibit improvement in throughput about average factor of 3.5 times SM performance in both vertical detectors and angular diversity detectors. As the performance of the system may be jeopardized by obstructions, specular and diffuse reflection models for indoor OWC systems using a mobile receiver with angular diversity detectors in MIMO channels are considered. The target is to improve the MIMO throughput compared to vertically oriented detectors by exploiting reflections from different reflecting surfaces in the room. The throughput across multiple locations in the small room by using RC, SMP and SM approaches is again evaluated. The results for LOS only channels against LOS with specular or diffuse reflection conditions, for both vertical and angular oriented receivers are then compared. The results show that exploiting specular and diffuse reflections provide significant improvements in link performance. For example the reflection coefficient (α) of 0.9 and the antenna separation of 0.6 m, RC diffuse model shows throughput improvement of about 1.8 times that of LOS for both vertical detectors and angular diversity receivers. SM diffuse model shows throughput improvement of about 3 times that of LOS for both vertical detectors and angular diversity receivers. ASM diffuse model shows throughput improvement of about 2 times that of LOS for both vertical detectors and angular diversity receivers. SMP diffuse model shows throughput improvement of about 1.5 times that of LOS for both vertical detectors and angular diversity receiver

Communication over Asynchronous Networks: Signaling and Rate-Reliability Analysis

Asynchronism inherently exists in many communication systems specially in multi-terminal networks mainly due to the effect of multi-path and propagation delay. While in theoretical analysis of communication systems perfect synchronization of the terminals is often presumed, in some cases in which the nodes are randomly distributed over a geometrical area, it might be impossible to synchronize the nodes even if an ideal infrastructure service provider is used. In this work, two major categories of multi-user communication systems, i.e., relay networks and interference channels, are considered and the effect of the asynchronism among the terminals on characteristic properties of these channels are investigated. In Chapter 2, the construction of distributed space-time codes for a general two-hop asynchronous cooperative relay network is considered. A novel algebraic structure is proposed and shown to achieve full diversity for arbitrary number of relays, arbitrary input alphabets, and arbitrary delay profiles among the relays. Unlike previously proposed delay tolerant schemes, the new design has minimum length which translates into smaller decoding complexity at the same transmission rate. Full-rate and full-diversity are achieved by the new designs with or without the use of guard intervals between successive transmissions. Simulation results confirm the mathematical analysis of the proposed codes. In Chapter 3, the underlying asynchronous network is examined for various relaying protocols such as non-orthogonal selection decode-and-forward, orthogonal selection decode-and-forward, non-orthogonal amplify-and-forward (NAF), and orthogonal amplify-and-forward (OAF). The transmitter nodes send pulse amplitude modulation (PAM) signals, in which information symbols are linearly modulated by a shaping waveform to be sent to the destination, asynchronously. We consider two different cases with respect to the type of the shaping waveforms used in the structure of the PAM signals. In the theoretical case where band-limited shaping waveforms are used, it is shown that the asynchronism does not affect the DMT performance of the system and the same DMT as that of the corresponding synchronous network is obtained for all the aforementioned protocols. In the practical case where time-limited shaping waveforms are used, it is shown that better diversity gains can be achieved at the expense of a bandwidth expansion. More precisely, in the decode-and-forward type protocols, the asynchronous network provides a better diversity gain than that of the corresponding synchronous network throughout the range of the multiplexing gain. In the amplify-and-forward type protocols, the asynchronous network provides the same DMT as that of the corresponding synchronous counterpart under the OAF protocol; however, a better diversity gain is achieved under the NAF protocol throughout the range of the multiplexing gain. In particular, in the single relay asynchronous network, the NAF protocol provides the same DMT as that of the 2 × 1 multiple-input single-output channel. In Chapter 4, a constant K-user interference channel in which the users are not symbol synchronous is considered. It is shown that the asynchronism among the users does not affect the total number of degrees of freedom (DOF) of this channel; however, it facilitates aligning interfering signals at each receiver node. To achieve the total K/2 DOF of this channel when single antenna nodes are used, a novel practical interference alignment scheme is proposed wherein the alignment task is performed with the help of asynchronous delays which inherently exist among the received signals at each receiver node. The asynchronism causes inter-symbol-interference (ISI) among transmitted symbols by different transmitters resulting in the underlying quasi-static links to be converted to ISI and accordingly into time varying channels. It is proved that this conversion solves the lack of channel variation required for the interference alignment in quasi-static scenarios. When each node is equipped with M > 1 antennas, it is argued that the same alignment scheme proposed for the single antenna nodes’ interference channel is sufficient to achieve the total MK/2 DOF of the medium provided that each pair of the transmitters and the receivers experience the same asynchronous delay for all the corresponding antennas. In contrast to previously proposed alignment schemes, the channel state information of the links does not need to be known at the transmitter nodes. Instead, the relative delays among the received signals at each receiver node are globally known to the entire network. While the asynchronism is usually treated as a troublesome factor in communication systems, in this dissertation, we are interested to introduce it as a useful property of the wireless medium similar to the fading which can improve the system performance in some communication scenarios or facilitate signaling over the medium in some other scenarios

Soft-demodulation of QPSK and 16-QAM for turbo coded WCDMA mobile communication systems

EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Near-capacity MIMOs using iterative detection

In this thesis, Multiple-Input Multiple-Output (MIMO) techniques designed for transmission over narrowband Rayleigh fading channels are investigated. Specifically, in order to providea diversity gain while eliminating the complexity of MIMO channel estimation, a Differential Space-Time Spreading (DSTS) scheme is designed that employs non-coherent detection. Additionally, in order to maximise the coding advantage of DSTS, it is combined with Sphere Packing (SP) modulation. The related capacity analysis shows that the DSTS-SP scheme exhibits a higher capacity than its counterpart dispensing with SP. Furthermore, in order to attain additional performance gains, the DSTS system invokes iterative detection, where the outer code is constituted by a Recursive Systematic Convolutional (RSC) code, while the inner code is a SP demapper in one of the prototype systems investigated, while the other scheme employs a Unity Rate Code (URC) as its inner code in order to eliminate the error floor exhibited by the system dispensing with URC. EXIT charts are used to analyse the convergence behaviour of the iteratively detected schemes and a novel technique is proposed for computing the maximum achievable rate of the system based on EXIT charts. Explicitly, the four-antenna-aided DSTSSP system employing no URC precoding attains a coding gain of 12 dB at a BER of 10-5 and performs within 1.82 dB from the maximum achievable rate limit. By contrast, the URC aidedprecoded system operates within 0.92 dB from the same limit.On the other hand, in order to maximise the DSTS system’s throughput, an adaptive DSTSSP scheme is proposed that exploits the advantages of differential encoding, iterative decoding as well as SP modulation. The achievable integrity and bit rate enhancements of the system are determined by the following factors: the specific MIMO configuration used for transmitting data from the four antennas, the spreading factor used and the RSC encoder’s code rate.Additionally, multi-functional MIMO techniques are designed to provide diversity gains, multiplexing gains and beamforming gains by combining the benefits of space-time codes, VBLASTand beamforming. First, a system employing Nt=4 transmit Antenna Arrays (AA) with LAA number of elements per AA and Nr=4 receive antennas is proposed, which is referred to as a Layered Steered Space-Time Code (LSSTC). Three iteratively detected near-capacity LSSTC-SP receiver structures are proposed, which differ in the number of inner iterations employed between the inner decoder and the SP demapper as well as in the choice of the outer code, which is either an RSC code or an Irregular Convolutional Code (IrCC). The three systems are capable of operating within 0.9, 0.4 and 0.6 dB from the maximum achievable rate limit of the system. A comparison between the three iteratively-detected schemes reveals that a carefully designed two-stage iterative detection scheme is capable of operating sufficiently close to capacity at a lower complexity, when compared to a three-stage system employing a RSC or a two-stage system using an IrCC as an outer code. On the other hand, in order to allow the LSSTC scheme to employ less receive antennas than transmit antennas, while still accommodating multiple users, a Layered Steered Space-Time Spreading (LSSTS) scheme is proposed that combines the benefits of space-time spreading, V-BLAST, beamforming and generalised MC DS-CDMA. Furthermore, iteratively detected LSSTS schemes are presented and an LLR post-processing technique is proposed in order to improve the attainable performance of the iteratively detected LSSTS system.Finally, a distributed turbo coding scheme is proposed that combines the benefits of turbo coding and cooperative communication, where iterative detection is employed by exchanging extrinsic information between the decoders of different single-antenna-aided users. Specifically, the effect of the errors induced in the first phase of cooperation, where the two users exchange their data, on the performance of the uplink in studied, while considering different fading channel characteristics

High capacity multiuser multiantenna communication techniques

One of the main issues involved in the development of future wireless communication systems is the multiple access technique used to efficiently share the available spectrum among users. In rich multipath environment, spatial dimension can be exploited to meet the increasing number of users and their demands without consuming extra bandwidth and power. Therefore, it is utilized in the multiple-input multiple-output (MIMO) technology to increase the spectral efficiency significantly. However, multiuser MIMO (MU-MIMO) systems are still challenging to be widely adopted in next generation standards. In this thesis, new techniques are proposed to increase the channel and user capacity and improve the error performance of MU-MIMO over Rayleigh fading channel environment. For realistic system design and performance evaluation, channel correlation is considered as one of the main channel impurities due its severe influence on capacity and reliability. Two simple methods called generalized successive coloring technique (GSCT) and generalized iterative coloring technique (GICT) are proposed for accurate generation of correlated Rayleigh fading channels (CRFC). They are designed to overcome the shortcomings of existing methods by avoiding factorization of desired covariance matrix of the Gaussian samples. The superiority of these techniques is demonstrated by extensive simulations of different practical system scenarios. To mitigate the effects of channel correlations, a novel constellation constrained MU-MIMO (CC-MU-MIMO) scheme is proposed using transmit signal design and maximum likelihood joint detection (MLJD) at the receiver. It is designed to maximize the channel capacity and error performance based on principles of maximizing the minimum Euclidean distance (dmin) of composite received signals. Two signal design methods named as unequal power allocation (UPA) and rotation constellation (RC) are utilized to resolve the detection ambiguity caused by correlation. Extensive analysis and simulations demonstrate the effectiveness of considered scheme compared with conventional MU-MIMO. Furthermore, significant gain in SNR is achieved particularly in moderate to high correlations which have direct impact to maintain high user capacity. A new efficient receive antenna selection (RAS) technique referred to as phase difference based selection (PDBS) is proposed for single and multiuser MIMO systems to maximize the capacity over CRFC. It utilizes the received signal constellation to select the subset of antennas with highest (dmin) constellations due to its direct impact on the capacity and BER performance. A low complexity algorithm is designed by employing the Euclidean norm of channel matrix rows with their corresponding phase differences. Capacity analysis and simulation results show that PDBS outperforms norm based selection (NBS) and near to optimal selection (OS) for all correlation and SNR values. This technique provides fast RAS to capture most of the gains promised by multiantenna systems over different channel conditions. Finally, novel group layered MU-MIMO (GL-MU-MIMO) scheme is introduced to exploit the available spectrum for higher user capacity with affordable complexity. It takes the advantages of spatial difference among users and power control at base station to increase the number of users beyond the available number of RF chains. It is achieved by dividing the users into two groups according to their received power, high power group (HPG) and low power group (LPG). Different configurations of low complexity group layered multiuser detection (GL-MUD) and group power allocation ratio (η) are utilized to provide a valuable tradeoff between complexity and overall system performance. Furthermore, RAS diversity is incorporated by using NBS and a new selection algorithm called HPG-PDBS to increase the channel capacity and enhance the error performance. Extensive analysis and simulations demonstrate the superiority of proposed scheme compared with conventional MU-MIMO. By using appropriate value of (η), it shows higher sum rate capacity and substantial increase in the user capacity up to two-fold at target BER and SNR values

Indoor Visible Light Communication:A Tutorial and Survey

Abstract With the advancement of solid-state devices for lighting, illumination is on the verge of being completely restructured. This revolution comes with numerous advantages and viable opportunities that can transform the world of wireless communications for the better. Solid-state LEDs are rapidly replacing the contemporary incandescent and fluorescent lamps. In addition to their high energy efficiency, LEDs are desirable for their low heat generation, long lifespan, and their capability to switch on and off at an extremely high rate. The ability of switching between different levels of luminous intensity at such a rate has enabled the inception of a new communication technology referred to as visible light communication (VLC). With this technology, the LED lamps are additionally being used for data transmission. This paper provides a tutorial and a survey of VLC in terms of the design, development, and evaluation techniques as well as current challenges and their envisioned solutions. The focus of this paper is mainly directed towards an indoor setup. An overview of VLC, theory of illumination, system receivers, system architecture, and ongoing developments are provided. We further provide some baseline simulation results to give a technical background on the performance of VLC systems. Moreover, we provide the potential of incorporating VLC techniques in the current and upcoming technologies such as fifth-generation (5G), beyond fifth-generation (B5G) wireless communication trends including sixth-generation (6G), and intelligent reflective surfaces (IRSs) among others

Design of tch-type sequences for communications

This thesis deals with the design of a class of cyclic codes inspired by TCH codewords. Since TCH codes are linked to finite fields the fundamental concepts and facts about abstract algebra, namely group theory and number theory, constitute the first part of the thesis. By exploring group geometric properties and identifying an equivalence between some operations on codes and the symmetries of the dihedral group we were able to simplify the generation of codewords thus saving on the necessary number of computations. Moreover, we also presented an algebraic method to obtain binary generalized TCH codewords of length N = 2k, k = 1,2, . . . , 16. By exploring Zech logarithm’s properties as well as a group theoretic isomorphism we developed a method that is both faster and less complex than what was proposed before. In addition, it is valid for all relevant cases relating the codeword length N and not only those resulting from N = p