Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review

The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER

Design and Analysis of Optical Interconnection Networks for Parallel Computation.

In this doctoral research, we propose several novel protocols and topologies for the interconnection of massively parallel processors. These new technologies achieve considerable improvements in system performance and structure simplicity. Currently, synchronous protocols are used in optical TDM buses. The major disadvantage of a synchronous protocol is the waste of packet slots. To offset this inherent drawback of synchronous TDM, a pipelined asynchronous TDM optical bus is proposed. The simulation results show that the performance of the proposed bus is significantly better than that of known pipelined synchronous TDM optical buses. Practically, the computation power of the plain TDM protocol is limited. Various extensions must be added to the system. In this research, a new pipelined optical TDM bus for implementing a linear array parallel computer architecture is proposed. The switches on the receiving segment of the bus can be dynamically controlled, which make the system highly reconfigurable. To build large and scalable systems, we need new network architectures that are suitable for optical interconnections. A new kind of reconfigurable bus called segmented bus is introduced to achieve reduced structure simplicity and increased concurrency. We show that parallel architectures based on segmented buses are versatile by showing that it can simulate parallel communication patterns supported by a wide variety of networks with small slowdown factors. New kinds of interconnection networks, the hypernetworks, have been proposed recently. Compared with point-to-point networks, they allow for increased resource-sharing and communication bandwidth utilization, and they are especially suitable for optical interconnects. One way to derive a hypernetwork is by finding the dual of a point-to-point network. Hypercube Q\sb{n}, where n is the dimension, is a very popular point-to-point network. It is interesting to construct hypernetworks from the dual Q\sbsp{n}{*} of hypercube of Q\sb{n}. In this research, the properties of Q\sbsp{n}{*} are investigated and a set of fundamental data communication algorithms for Q\sbsp{n}{*} are presented. The results indicate that the Q\sbsp{n}{*} hypernetwork is a useful and promising interconnection structure for high-performance parallel and distributed computing systems

Efficient parallel processing with optical interconnections

With the advances in VLSI technology, it is now possible to build chips which can each contain thousands of processors. The efficiency of such chips in executing parallel algorithms heavily depends on the interconnection topology of the processors. It is not possible to build a fully interconnected network of processors with constant fan-in/fan-out using electrical interconnections. Free space optics is a remedy to this limitation. Qualities exclusive to the optical medium are its ability to be directed for propagation in free space and the property that optical channels can cross in space without any interference. In this thesis, we present an electro-optical interconnected architecture named Optical Reconfigurable Mesh (ORM). It is based on an existing optical model of computation. There are two layers in the architecture. The processing layer is a reconfigurable mesh and the deflecting layer contains optical devices to deflect light beams. ORM provides three types of communication mechanisms. The first is for arbitrary planar connections among sets of locally connected processors using the reconfigurable mesh. The second is for arbitrary connections among N of the processors using the electrical buses on the processing layer and N2 fixed passive deflecting units on the deflection layer. The third is for arbitrary connections among any of the N2 processors using the N2 mechanically reconfigurable deflectors in the deflection layer. The third type of communication mechanisms is significantly slower than the other two. Therefore, it is desirable to avoid reconfiguring this type of communication during the execution of the algorithms. Instead, the optical reconfiguration can be done before the execution of each algorithm begins. Determining a right configuration that would be suitable for the entire configuration of a task execution is studied in this thesis. The basic data movements for each of the mechanisms are studied. Finally, to show the power of ORM, we use all three types of communication mechanisms in the first O(logN) time algorithm for finding the convex hulls of all figures in an N x N binary image presented in this thesis

Efficient parallel computation on multiprocessors with optical interconnection networks

This dissertation studies optical interconnection networks, their architecture, address schemes, and computation and communication capabilities. We focus on a simple but powerful optical interconnection network model - the Linear Array with Reconfigurable pipelined Bus System (LARPBS). We extend the LARPBS model to a simplified higher dimensional LAPRBS and provide a set of basic computation operations. We then study the following two groups of parallel computation problems on both one dimensional LARPBS\u27s as well as multi-dimensional LARPBS\u27s: parallel comparison problems, including sorting, merging, and selection; Boolean matrix multiplication, transitive closure and their applications to connected component problems. We implement an optimal sorting algorithm on an n-processor LARPBS. With this optimal sorting algorithm at disposal, we study the sorting problem for higher dimensional LARPBS\u27s and obtain the following results: • An optimal basic Columnsort algorithm on a 2D LARPBS. • Two optimal two-way merge sort algorithms on a 2D LARPBS. • An optimal multi-way merge sorting algorithm on a 2D LARPBS. • An optimal generalized column sort algorithm on a 2D LARPBS. • An optimal generalized column sort algorithm on a 3D LARPBS. • An optimal 5-phase sorting algorithm on a 3D LARPBS. Results for selection problems are as follows: • A constant time maximum-finding algorithm on an LARPBS. • An optimal maximum-finding algorithm on an LARPBS. • An O((log log n)2) time parallel selection algorithm on an LARPBS. • An O(k(log log n)2) time parallel multi-selection algorithm on an LARPBS. While studying the computation and communication properties of the LARPBS model, we find Boolean matrix multiplication and its applications to the graph are another set of problem that can be solved efficiently on the LARPBS. Following is a list of results we have obtained in this area. • A constant time Boolean matrix multiplication algorithm. • An O(log n)-time transitive closure algorithm. • An O(log n)-time connected components algorithm. • An O(log n)-time strongly connected components algorithm. The results provided in this dissertation show the strong computation and communication power of optical interconnection networks

Simulating a Pipelined Reconfigurable Mesh on a Linear Array with a Reconfigurable Pipelined Bus System

Due to the unidirectional nature of propagation and predictable delays, optically pipelined buses have been gaining more attention. There have been many models proposed over time that use reconfigurable optically pipelined buses. The reconfigurable nature of the models makes them capable of changing their component’s functionalities and structure that connects the components at every step of computation. There are both one dimensional as well as k –dimensional models that have been proposed in the literature. Though equivalence between various one dimensional models and equivalence between different two dimensional models had been established, so far there has not been any attempt to explore the relationship between a one dimensional model and a two dimensional model. In the proposed research work it is shown that a move from one to two or more dimensions does not cause any increase in the volume of communication between the processors as they communicate in a pipelined manner on the same optical bus. When moving from two dimensions to one dimension, the challenge is to map the processors so that those belonging to a two-dimensional bus segment are contiguous and in the same order on the one-dimensional model. This does not increase any increase in communication overhead as the processors instead of communicating on two dimensional buses now communicate on a linear one dimensional bus structure. To explore the relationship between one dimensional and two dimensional models a commonly used model Linear Array with a Reconfigurable Pipelined Bus System (LARPBS) and its two dimensional counterpart Pipelined Reconfigurable Mesh (PR-Mesh) are chosen Here an attempt has been made to present a simulation of a two dimensional PR-Mesh on a one dimensional LARPBS to establish complexity of the models with respect to one another, and to determine the efficiency with which the LARPBS can simulate the PR-Mesh

FPGA structures for high speed and low overhead dynamic circuit specialization

A Field Programmable Gate Array (FPGA) is a programmable digital electronic chip. The FPGA does not come with a predefined function from the manufacturer; instead, the developer has to define its function through implementing a digital circuit on the FPGA resources. The functionality of the FPGA can be reprogrammed as desired and hence the name “field programmable”. FPGAs are useful in small volume digital electronic products as the design of a digital custom chip is expensive. Changing the FPGA (also called configuring it) is done by changing the configuration data (in the form of bitstreams) that defines the FPGA functionality. These bitstreams are stored in a memory of the FPGA called configuration memory. The SRAM cells of LookUp Tables (LUTs), Block Random Access Memories (BRAMs) and DSP blocks together form the configuration memory of an FPGA. The configuration data can be modified according to the user’s needs to implement the user-defined hardware. The simplest way to program the configuration memory is to download the bitstreams using a JTAG interface. However, modern techniques such as Partial Reconfiguration (PR) enable us to configure a part in the configuration memory with partial bitstreams during run-time. The reconfiguration is achieved by swapping in partial bitstreams into the configuration memory via a configuration interface called Internal Configuration Access Port (ICAP). The ICAP is a hardware primitive (macro) present in the FPGA used to access the configuration memory internally by an embedded processor. The reconfiguration technique adds flexibility to use specialized ci rcuits that are more compact and more efficient t han t heir b ulky c ounterparts. An example of such an implementation is the use of specialized multipliers instead of big generic multipliers in an FIR implementation with constant coefficients. To specialize these circuits and reconfigure during the run-time, researchers at the HES group proposed the novel technique called parameterized reconfiguration that can be used to efficiently and automatically implement Dynamic Circuit Specialization (DCS) that is built on top of the Partial Reconfiguration method. It uses the run-time reconfiguration technique that is tailored to implement a parameterized design. An application is said to be parameterized if some of its input values change much less frequently than the rest. These inputs are called parameters. Instead of implementing these parameters as regular inputs, in DCS these inputs are implemented as constants, and the application is optimized for the constants. For every change in parameter values, the design is re-optimized (specialized) during run-time and implemented by reconfiguring the optimized design for a new set of parameters. In DCS, the bitstreams of the parameterized design are expressed as Boolean functions of the parameters. For every infrequent change in parameters, a specialized FPGA configuration is generated by evaluating the corresponding Boolean functions, and the FPGA is reconfigured with the specialized configuration. A detailed study of overheads of DCS and providing suitable solutions with appropriate custom FPGA structures is the primary goal of the dissertation. I also suggest different improvements to the FPGA configuration memory architecture. After offering the custom FPGA structures, I investigated the role of DCS on FPGA overlays and the use of custom FPGA structures that help to reduce the overheads of DCS on FPGA overlays. By doing so, I hope I can convince the developer to use DCS (which now comes with minimal costs) in real-world applications. I start the investigations of overheads of DCS by implementing an adaptive FIR filter (using the DCS technique) on three different Xilinx FPGA platforms: Virtex-II Pro, Virtex-5, and Zynq-SoC. The study of how DCS behaves and what is its overhead in the evolution of the three FPGA platforms is the non-trivial basis to discover the costs of DCS. After that, I propose custom FPGA structures (reconfiguration controllers and reconfiguration drivers) to reduce the main overhead (reconfiguration time) of DCS. These structures not only reduce the reconfiguration time but also help curbing the power hungry part of the DCS system. After these chapters, I study the role of DCS on FPGA overlays. I investigate the effect of the proposed FPGA structures on Virtual-Coarse-Grained Reconfigurable Arrays (VCGRAs). I classify the VCGRA implementations into three types: the conventional VCGRA, partially parameterized VCGRA and fully parameterized VCGRA depending upon the level of parameterization. I have designed two variants of VCGRA grids for HPC image processing applications, namely, the MAC grid and Pixie. Finally, I try to tackle the reconfiguration time overhead at the hardware level of the FPGA by customizing the FPGA configuration memory architecture. In this part of my research, I propose to use a parallel memory structure to improve the reconfiguration time of DCS drastically. However, this improvement comes with a significant overhead of hardware resources which will need to be solved in future research on commercial FPGA configuration memory architectures

A Dynamically Reconfigurable Parallel Processing Framework with Application to High-Performance Video Processing

Digital video processing demands have and will continue to grow at unprecedented rates. Growth comes from ever increasing volume of data, demand for higher resolution, higher frame rates, and the need for high capacity communications. Moreover, economic realities force continued reductions in size, weight and power requirements. The ever-changing needs and complexities associated with effective video processing systems leads to the consideration of dynamically reconfigurable systems. The goal of this dissertation research was to develop and demonstrate the viability of integrated parallel processing system that effectively and efficiently apply pre-optimized hardware cores for processing video streamed data. Digital video is decomposed into packets which are then distributed over a group of parallel video processing cores. Real time processing requires an effective task scheduler that distributes video packets efficiently to any of the reconfigurable distributed processing nodes across the framework, with the nodes running on FPGA reconfigurable logic in an inherently Virtual\u27 mode. The developed framework, coupled with the use of hardware techniques for dynamic processing optimization achieves an optimal cost/power/performance realization for video processing applications. The system is evaluated by testing processor utilization relative to I/O bandwidth and algorithm latency using a separable 2-D FIR filtering system, and a dynamic pixel processor. For these applications, the system can achieve performance of hundreds of 640x480 video frames per second across an eight lane Gen I PCIe bus. Overall, optimal performance is achieved in the sense that video data is processed at the maximum possible rate that can be streamed through the processing cores. This performance, coupled with inherent ability to dynamically add new algorithms to the described dynamically reconfigurable distributed processing framework, creates new opportunities for realizable and economic hardware virtualization.\u2

Cross-Layer Rapid Prototyping and Synthesis of Application-Specific and Reconfigurable Many-accelerator Platforms

Technological advances of recent years laid the foundation consolidation of informatisationof society, impacting on economic, political, cultural and socialdimensions. At the peak of this realization, today, more and more everydaydevices are connected to the web, giving the term ”Internet of Things”. The futureholds the full connection and interaction of IT and communications systemsto the natural world, delimiting the transition to natural cyber systems and offeringmeta-services in the physical world, such as personalized medical care, autonomoustransportation, smart energy cities etc. . Outlining the necessities of this dynamicallyevolving market, computer engineers are required to implement computingplatforms that incorporate both increased systemic complexity and also cover awide range of meta-characteristics, such as the cost and design time, reliabilityand reuse, which are prescribed by a conflicting set of functional, technical andconstruction constraints. This thesis aims to address these design challenges bydeveloping methodologies and hardware/software co-design tools that enable therapid implementation and efficient synthesis of architectural solutions, which specifyoperating meta-features required by the modern market. Specifically, this thesispresents a) methodologies to accelerate the design flow for both reconfigurableand application-specific architectures, b) coarse-grain heterogeneous architecturaltemplates for processing and communication acceleration and c) efficient multiobjectivesynthesis techniques both at high abstraction level of programming andphysical silicon level.Regarding to the acceleration of the design flow, the proposed methodologyemploys virtual platforms in order to hide architectural details and drastically reducesimulation time. An extension of this framework introduces the systemicco-simulation using reconfigurable acceleration platforms as co-emulation intermediateplatforms. Thus, the development cycle of a hardware/software productis accelerated by moving from a vertical serial flow to a circular interactive loop.Moreover the simulation capabilities are enriched with efficient detection and correctiontechniques of design errors, as well as control methods of performancemetrics of the system according to the desired specifications, during all phasesof the system development. In orthogonal correlation with the aforementionedmethodological framework, a new architectural template is proposed, aiming atbridging the gap between design complexity and technological productivity usingspecialized hardware accelerators in heterogeneous systems-on-chip and networkon-chip platforms. It is presented a novel co-design methodology for the hardwareaccelerators and their respective programming software, including the tasks allocationto the available resources of the system/network. The introduced frameworkprovides implementation techniques for the accelerators, using either conventionalprogramming flows with hardware description language or abstract programmingmodel flows, using techniques from high-level synthesis. In any case, it is providedthe option of systemic measures optimization, such as the processing speed,the throughput, the reliability, the power consumption and the design silicon area.Finally, on addressing the increased complexity in design tools of reconfigurablesystems, there are proposed novel multi-objective optimization evolutionary algo-rithms which exploit the modern multicore processors and the coarse-grain natureof multithreaded programming environments (e.g. OpenMP) in order to reduce theplacement time, while by simultaneously grouping the applications based on theirintrinsic characteristics, the effectively explore the design space effectively.The efficiency of the proposed architectural templates, design tools and methodologyflows is evaluated in relation to the existing edge solutions with applicationsfrom typical computing domains, such as digital signal processing, multimedia andarithmetic complexity, as well as from systemic heterogeneous environments, suchas a computer vision system for autonomous robotic space navigation and manyacceleratorsystems for HPC and workstations/datacenters. The results strengthenthe belief of the author, that this thesis provides competitive expertise to addresscomplex modern - and projected future - design challenges.Οι τεχνολογικές εξελίξεις των τελευταίων ετών έθεσαν τα θεμέλια εδραίωσης της πληροφοριοποίησης της κοινωνίας, επιδρώντας σε οικονομικές,πολιτικές, πολιτιστικές και κοινωνικές διαστάσεις. Στο απόγειο αυτής τη ςπραγμάτωσης, σήμερα, ολοένα και περισσότερες καθημερινές συσκευές συνδέονται στο παγκόσμιο ιστό, αποδίδοντας τον όρο «Ίντερνετ των πραγμάτων».Το μέλλον επιφυλάσσει την πλήρη σύνδεση και αλληλεπίδραση των συστημάτων πληροφορικής και επικοινωνιών με τον φυσικό κόσμο, οριοθετώντας τη μετάβαση στα συστήματα φυσικού κυβερνοχώρου και προσφέροντας μεταυπηρεσίες στον φυσικό κόσμο όπως προσωποποιημένη ιατρική περίθαλψη, αυτόνομες μετακινήσεις, έξυπνες ενεργειακά πόλεις κ.α. . Σκιαγραφώντας τις ανάγκες αυτής της δυναμικά εξελισσόμενης αγοράς, οι μηχανικοί υπολογιστών καλούνται να υλοποιήσουν υπολογιστικές πλατφόρμες που αφενός ενσωματώνουν αυξημένη συστημική πολυπλοκότητα και αφετέρου καλύπτουν ένα ευρύ φάσμα μεταχαρακτηριστικών, όπως λ.χ. το κόστος σχεδιασμού, ο χρόνος σχεδιασμού, η αξιοπιστία και η επαναχρησιμοποίηση, τα οποία προδιαγράφονται από ένα αντικρουόμενο σύνολο λειτουργικών, τεχνολογικών και κατασκευαστικών περιορισμών. Η παρούσα διατριβή στοχεύει στην αντιμετώπιση των παραπάνω σχεδιαστικών προκλήσεων, μέσω της ανάπτυξης μεθοδολογιών και εργαλείων συνσχεδίασης υλικού/λογισμικού που επιτρέπουν την ταχεία υλοποίηση καθώς και την αποδοτική σύνθεση αρχιτεκτονικών λύσεων, οι οποίες προδιαγράφουν τα μετα-χαρακτηριστικά λειτουργίας που απαιτεί η σύγχρονη αγορά. Συγκεκριμένα, στα πλαίσια αυτής της διατριβής, παρουσιάζονται α) μεθοδολογίες επιτάχυνσης της ροής σχεδιασμού τόσο για επαναδιαμορφούμενες όσο και για εξειδικευμένες αρχιτεκτονικές, β) ετερογενή αδρομερή αρχιτεκτονικά πρότυπα επιτάχυνσης επεξεργασίας και επικοινωνίας και γ) αποδοτικές τεχνικές πολυκριτηριακής σύνθεσης τόσο σε υψηλό αφαιρετικό επίπεδο προγραμματισμού,όσο και σε φυσικό επίπεδο πυριτίου.Αναφορικά προς την επιτάχυνση της ροής σχεδιασμού, προτείνεται μια μεθοδολογία που χρησιμοποιεί εικονικές πλατφόρμες, οι οποίες αφαιρώντας τις αρχιτεκτονικές λεπτομέρειες καταφέρνουν να μειώσουν σημαντικά το χρόνο εξομοίωσης. Παράλληλα, εισηγείται η συστημική συν-εξομοίωση με τη χρήση επαναδιαμορφούμενων πλατφορμών, ως μέσων επιτάχυνσης. Με αυτόν τον τρόπο, ο κύκλος ανάπτυξης ενός προϊόντος υλικού, μετατεθειμένος από την κάθετη σειριακή ροή σε έναν κυκλικό αλληλεπιδραστικό βρόγχο, καθίσταται ταχύτερος, ενώ οι δυνατότητες προσομοίωσης εμπλουτίζονται με αποδοτικότερες μεθόδους εντοπισμού και διόρθωσης σχεδιαστικών σφαλμάτων, καθώς και μεθόδους ελέγχου των μετρικών απόδοσης του συστήματος σε σχέση με τις επιθυμητές προδιαγραφές, σε όλες τις φάσεις ανάπτυξης του συστήματος. Σε ορθογώνια συνάφεια με το προαναφερθέν μεθοδολογικό πλαίσιο, προτείνονται νέα αρχιτεκτονικά πρότυπα που στοχεύουν στη γεφύρωση του χάσματος μεταξύ της σχεδιαστικής πολυπλοκότητας και της τεχνολογικής παραγωγικότητας, με τη χρήση συστημάτων εξειδικευμένων επιταχυντών υλικού σε ετερογενή συστήματα-σε-ψηφίδα καθώς και δίκτυα-σε-ψηφίδα. Παρουσιάζεται κατάλληλη μεθοδολογία συν-σχεδίασης των επιταχυντών υλικού και του λογισμικού προκειμένου να αποφασισθεί η κατανομή των εργασιών στους διαθέσιμους πόρους του συστήματος/δικτύου. Το μεθοδολογικό πλαίσιο προβλέπει την υλοποίηση των επιταχυντών είτε με συμβατικές μεθόδους προγραμματισμού σε γλώσσα περιγραφής υλικού είτε με αφαιρετικό προγραμματιστικό μοντέλο με τη χρήση τεχνικών υψηλού επιπέδου σύνθεσης. Σε κάθε περίπτωση, δίδεται η δυνατότητα στο σχεδιαστή για βελτιστοποίηση συστημικών μετρικών, όπως η ταχύτητα επεξεργασίας, η ρυθμαπόδοση, η αξιοπιστία, η κατανάλωση ενέργειας και η επιφάνεια πυριτίου του σχεδιασμού. Τέλος, προκειμένου να αντιμετωπισθεί η αυξημένη πολυπλοκότητα στα σχεδιαστικά εργαλεία επαναδιαμορφούμενων συστημάτων, προτείνονται νέοι εξελικτικοί αλγόριθμοι πολυκριτηριακής βελτιστοποίησης, οι οποίοι εκμεταλλευόμενοι τους σύγχρονους πολυπύρηνους επεξεργαστές και την αδρομερή φύση των πολυνηματικών περιβαλλόντων προγραμματισμού (π.χ. OpenMP), μειώνουν το χρόνο επίλυσης του προβλήματος της τοποθέτησης των λογικών πόρων σε φυσικούς,ενώ ταυτόχρονα, ομαδοποιώντας τις εφαρμογές βάση των εγγενών χαρακτηριστικών τους, διερευνούν αποτελεσματικότερα το χώρο σχεδίασης.Η αποδοτικότητά των προτεινόμενων αρχιτεκτονικών προτύπων και μεθοδολογιών επαληθεύτηκε σε σχέση με τις υφιστάμενες λύσεις αιχμής τόσο σε αυτοτελής εφαρμογές, όπως η ψηφιακή επεξεργασία σήματος, τα πολυμέσα και τα προβλήματα αριθμητικής πολυπλοκότητας, καθώς και σε συστημικά ετερογενή περιβάλλοντα, όπως ένα σύστημα όρασης υπολογιστών για αυτόνομα διαστημικά ρομποτικά οχήματα και ένα σύστημα πολλαπλών επιταχυντών υλικού για σταθμούς εργασίας και κέντρα δεδομένων, στοχεύοντας εφαρμογές υψηλής υπολογιστικής απόδοσης (HPC). Τα αποτελέσματα ενισχύουν την πεποίθηση του γράφοντα, ότι η παρούσα διατριβή παρέχει ανταγωνιστική τεχνογνωσία για την αντιμετώπιση των πολύπλοκων σύγχρονων και προβλεπόμενα μελλοντικών σχεδιαστικών προκλήσεων