41 research outputs found

    Computation and analysis of natural compliance in fixturing and grasping arrangements

    Get PDF
    This paper computes and analyzes the natural compliance of fixturing and grasping arrangements. Traditionally, linear-spring contact models have been used to determine the natural compliance of multiple contact arrangements. However, these models are not supported by experiments or elasticity theory. We derive a closed-form formula for the stiffness matrix of multiple contact arrangements that admits a variety of nonlinear contact models, including the well-justified Hertz model. The stiffness matrix formula depends on the geometrical and material properties of the contacting bodies and on the initial loading at the contacts. We use the formula to analyze the relative influence of first- and second-order geometrical effects on the stability of multiple contact arrangements. Second-order effects, i.e., curvature effects, are often practically beneficial and sometimes lead to significant grasp stabilization. However, in some contact arrangements, curvature has a dominant destabilizing influence. Such contact arrangements are deemed stable under an all-rigid body model but, in fact, are unstable when the natural compliance of the contacting bodies is taken into account. We also consider the combined influence of curvature and contact preloading on stability. Contrary to conventional wisdom, under certain curvature conditions, higher preloading can increase rather than decrease grasp stability. Finally, we use the stiffness matrix formula to investigate the impact of different choices of contact model on the assessment of the stability of multiple contact arrangements. While the linear-spring model and the more realistic Hertz model usually lead to the same stability conclusions, in some cases, the two models lead to different stability results

    Constructing minimum deflection fixture arrangements using frame invariant norms

    Get PDF
    This paper describes a fixture planning method that minimizes object deflection under external loads. The method takes into account the natural compliance of the contacting bodies and applies to two-dimensional and three-dimensional quasirigid bodies. The fixturing method is based on a quality measure that characterizes the deflection of a fixtured object in response to unit magnitude wrenches. The object deflection measure is defined in terms of frame-invariant rigid body velocity and wrench norms and is therefore frame invariant. The object deflection measure is applied to the planning of optimal fixture arrangements of polygonal objects. We describe minimum-deflection fixturing algorithms for these objects, and make qualitative observations on the optimal arrangements generated by the algorithms. Concrete examples illustrate the minimum deflection fixturing method. Note to Practitioners-During fixturing, a workpiece needs to not only be stable against external perturbations, but must also stay within a specified tolerance in response to machining or assembly forces. This paper describes a fixture planning approach that minimizes object deflection under applied work loads. The paper describes how to take local material deformation effects into account, using a generic quasirigid contact model. Practical algorithms that compute the optimal fixturing arrangements of polygonal workpieces are described and examples are then presented

    Experiments in fixturing mechanics

    Get PDF
    This paper describes an experimental fixturing system wherein fixel reaction forces, workpiece loading, and workpiece displacements are measured during simulated fixturing operations. The system's configuration, its measurement principles, and tests to characterize its performance are summarized. This system is used to experimentally determine the relationship between workpiece displacement and variations in fixed preload force or workpiece loading. We compare the results against standard theories, and conclude that commonly used linear spring models do not accurately predict workpiece displacements, while a non-linear compliance model provides better predictive behavior

    Mobility of bodies in contact. I. A 2nd-order mobility index formultiple-finger grasps

    Get PDF
    Using a configuration-space approach, the paper develops a 2nd-order mobility theory for rigid bodies in contact. A major component of this theory is a coordinate invariant 2nd-order mobility index for a body, B, in frictionless contact with finger bodies A1,...A k. The index is an integer that captures the inherent mobility of B in an equilibrium grasp due to second order, or surface curvature, effects. It differentiates between grasps which are deemed equivalent by classical 1st-order theories, but are physically different. We further show that 2nd-order effects can be used to lower the effective mobility of a grasped object, and discuss implications of this result for achieving new lower bounds on the number of contacting finger bodies needed to immobilize an object. Physical interpretation and stability analysis of 2nd-order effects are taken up in the companion pape

    Mobility of bodies in contact. II. How forces are generated bycurvature effects

    Get PDF
    For part I, see ibid., p.696-708. The paper considers how forces are produced by compliance and surface curvature effects in systems where an object a is kinematically immobilized to second-order by finger bodies Al,...,Ak. A class of configuration-space based elastic deformation models is introduced. Using these elastic deformation models, it is shown that any object which is kinematically immobilized to first or second-order is also dynamically locally asymptotically stable with respect to perturbations. Moreover, it is shown that for preloaded grasps kinematic immobility implies that the stiffness matrix of the grasp is positive definite. The stability result provides physical justification for using second-order effects for purposes of immobilization in practical applications. Simulations illustrate the concepts

    Autonomous Mechanical Assembly on the Space Shuttle: An Overview

    Get PDF
    The space shuttle will be equipped with a pair of 50 ft. manipulators used to handle payloads and to perform mechanical assembly operations. Although current plans call for these manipulators to be operated by a human teleoperator. The possibility of using results from robotics and machine intelligence to automate this shuttle assembly system was investigated. The major components of an autonomous mechanical assembly system are examined, along with the technology base upon which they depend. The state of the art in advanced automation is also assessed

    Anthropomorphic robot finger with multi-point tactile sensation

    Get PDF
    Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2001.Includes bibliographical references (p. 84-95).The goal of this research is to develop the prototype of a tactile sensing platform for anthropomorphic manipulation research. We investigate this problem through the fabrication and simple control of a planar 2-DOF robotic finger inspired by anatomic consistency, self-containment, and adaptability. The robot is equipped with a tactile sensor array based on optical transducer technology whereby localized changes in light intensity within an illuminated foam substrate correspond to the distribution and magnitude of forces applied to the sensor surface plane [58]. The integration of tactile perception is a key component in realizing robotic systems which organically interact with the world. Such natural behavior is characterized by compliant performance that can initiate internal, and respond to external, force application in a dynamic environment. However, most of the current manipulators that support some form of haptic feedback, either solely derive proprioceptive sensation or only limit tactile sensors to the mechanical fingertips. These constraints are due to the technological challenges involved in high resolution, multi-point tactile perception. In this work, however, we take the opposite approach, emphasizing the role of full-finger tactile feedback in the refinement of manual capabilities. To this end, we propose and implement a control framework for sensorimotor coordination analogous to infant-level grasping and fixturing reflexes. This thesis details the mechanisms used to achieve these sensory, actuation, and control objectives, along with the design philosophies and biological influences behind them. The results of behavioral experiments with the tactilely-modulated control scheme are also described. The hope is to integrate the modular finger into an engineered analog of the human hand with a complete haptic system.by Jessica Lauren Banks.S.M

    Grasp Stability Analysis with Passive Reactions

    Get PDF
    Despite decades of research robotic manipulation systems outside of highly-structured industrial applications are still far from ubiquitous. Perhaps particularly curious is the fact that there appears to be a large divide between the theoretical grasp modeling literature and the practical manipulation community. Specifically, it appears that the most successful approaches to tasks such as pick-and-place or grasping in clutter are those that have opted for simple grippers or even suction systems instead of dexterous multi-fingered platforms. We argue that the reason for the success of these simple manipulation systemsis what we call passive stability: passive phenomena due to nonbackdrivable joints or underactuation allow for robust grasping without complex sensor feedback or controller design. While these effects are being leveraged to great effect, it appears the practical manipulation community lacks the tools to analyze them. In fact, we argue that the traditional grasp modeling theory assumes a complexity that most robotic hands do not possess and is therefore of limited applicability to the robotic hands commonly used today. We discuss these limitations of the existing grasp modeling literature and setout to develop our own tools for the analysis of passive effects in robotic grasping. We show that problems of this kind are difficult to solve due to the non-convexity of the Maximum Dissipation Principle (MDP), which is part of the Coulomb friction law. We show that for planar grasps the MDP can be decomposed into a number of piecewise convex problems, which can be solved for efficiently. Despite decades of research robotic manipulation systems outside of highlystructured industrial applications are still far from ubiquitous. Perhaps particularly curious is the fact that there appears to be a large divide between the theoretical grasp modeling literature and the practical manipulation community. Specifically, it appears that the most successful approaches to tasks such as pick-and-place or grasping in clutter are those that have opted for simple grippers or even suction systems instead of dexterous multi-fingered platforms. We argue that the reason for the success of these simple manipulation systemsis what we call passive stability: passive phenomena due to nonbackdrivable joints or underactuation allow for robust grasping without complex sensor feedback or controller design. While these effects are being leveraged to great effect, it appears the practical manipulation community lacks the tools to analyze them. In fact, we argue that the traditional grasp modeling theory assumes a complexity that most robotic hands do not possess and is therefore of limited applicability to the robotic hands commonly used today. We discuss these limitations of the existing grasp modeling literature and setout to develop our own tools for the analysis of passive effects in robotic grasping. We show that problems of this kind are difficult to solve due to the non-convexity of the Maximum Dissipation Principle (MDP), which is part of the Coulomb friction law. We show that for planar grasps the MDP can be decomposed into a number of piecewise convex problems, which can be solved for efficiently. We show that the number of these piecewise convex problems is quadratic in the number of contacts and develop a polynomial time algorithm for their enumeration. Thus, we present the first polynomial runtime algorithm for the determination of passive stability of planar grasps. For the spacial case we present the first grasp model that captures passive effects due to nonbackdrivable actuators and underactuation. Formulating the grasp model as a Mixed Integer Program we illustrate that a consequence of omitting the maximum dissipation principle from this formulation is the introduction of solutions that violate energy conservation laws and are thus unphysical. We propose a physically motivated iterative scheme to mitigate this effect and thus provide the first algorithm that allows for the determination of passive stability for spacial grasps with both fully actuated and underactuated robotic hands. We verify the accuracy of our predictions with experimental data and illustrate practical applications of our algorithm. We build upon this work and describe a convex relaxation of the Coulombfriction law and a successive hierarchical tightening approach that allows us to find solutions to the exact problem including the maximum dissipation principle. It is the first grasp stability method that allows for the efficient solution of the passive stability problem to arbitrary accuracy. The generality of our grasp model allows us to solve a wide variety of problems such as the computation of optimal actuator commands. This makes our framework a valuable tool for practical manipulation applications. Our work is relevant beyond robotic manipulation as it applies to the stability of any assembly of rigid bodies with frictional contacts, unilateral constraints and externally applied wrenches. Finally, we argue that with the advent of data-driven methods as well as theemergence of a new generation of highly sensorized hands there are opportunities for the application of the traditional grasp modeling theory to fields such as robotic in-hand manipulation through model-free reinforcement learning. We present a method that applies traditional grasp models to maintain quasi-static stability throughout a nominally model-free reinforcement learning task. We suggest that such methods can potentially reduce the sample complexity of reinforcement learning for in-hand manipulation.We show that the number of these piecewise convex problems is quadratic in the number of contacts and develop a polynomial time algorithm for their enumeration. Thus, we present the first polynomial runtime algorithm for the determination of passive stability of planar grasps
    corecore