A design for testability study on a high performance automatic gain control circuit.

A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

Product assurance technology for custom LSI/VLSI electronics

The technology for obtaining custom integrated circuits from CMOS-bulk silicon foundries using a universal set of layout rules is presented. The technical efforts were guided by the requirement to develop a 3 micron CMOS test chip for the Combined Release and Radiation Effects Satellite (CRRES). This chip contains both analog and digital circuits. The development employed all the elements required to obtain custom circuits from silicon foundries, including circuit design, foundry interfacing, circuit test, and circuit qualification

Single-Event Upset Analysis and Protection in High Speed Circuits

The effect of single-event transients (SETs) (at a combinational node of a design) on the system reliability is becoming a big concern for ICs manufactured using advanced technologies. An SET at a node of combinational part may cause a transient pulse at the input of a flip-flop and consequently is latched in the flip-flop and generates a soft-error. When an SET conjoined with a transition at a node along a critical path of the combinational part of a design, a transient delay fault may occur at the input of a flip-flop. On the other hand, increasing pipeline depth and using low power techniques such as multi-level power supply, and multi-threshold transistor convert almost all paths in a circuit to critical ones. Thus, studying the behavior of the SET in these kinds of circuits needs special attention. This paper studies the dynamic behavior of a circuit with massive critical paths in the presence of an SET. We also propose a novel flip-flop architecture to mitigate the effects of such SETs in combinational circuits. Furthermore, the proposed architecture can tolerant a single event upset (SEU) caused by particle strike on the internal nodes of a flip-flo

The Rolf of Test Chips in Coordinating Logic and Circuit Design and Layout Aids for VLSI

This paper emphasizes the need for multipurpose test chips and comprehensive procedures for use in supplying accurate input data to both logic and circuit simulators and chip layout aids. It is shown that the location of test structures within test chips is critical in obtaining representative data, because geometrical distortions introduced during the photomasking process can lead to significant intrachip parameter variations. In order to transfer test chip designs quickly, accurately, and economically, a commonly accepted portable chip layout notation and commonly accepted parametric tester language are needed. In order to measure test chips more accurately and more rapidly, parametric testers with improved architecture need to be developed in conjunction with innovative test structures with on-chip signal conditioning

A collection of fuzzy logic-based tools for the automated design, modelling and test of analog circuits

We have developed a collection of tools for the design, modeling, and test of analog circuits. Sharing a common fuzzy-logic based framework, the tools are part of FASY (Fuzzy-Logic-Based Analog Synthesis), an analog design package developed at the University of Seville. The first tool uses fuzzy logic for topology selection of analog cells. It follows decision rules directly entered by a human expert or automatically generated from its experience with earlier designs. Second, a performance-modeling tool provides a qualitative description of a circuit's behavior. Alternatively, it can use a learning process to accurately model circuit performance. Finally, an analog testing tool uses a fuzzy-neuron classifier to detect and classify faults in analog circuits

A comprehensive comparison between design for testability techniques for total dose testing of flash-based FPGAs

Radiation sources exist in different kinds of environments where electronic devices often operate. Correct device operation is usually affected negatively by radiation. The radiation resultant effect manifests in several forms depending on the operating environment of the device like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). CMOS circuits and Floating gate MOS circuits suffer from an increase in the delay and the leakage current due to TID effect. This may damage the proper operation of the integrated circuit. Exhaustive testing is needed for devices operating in harsh conditions like space and military applications to ensure correct operations in the worst circumstances. The use of worst case test vectors (WCTVs) for testing is strongly recommended by MIL-STD-883, method 1019, which is the standard describing the procedure for testing electronic devices under radiation. However, the difficulty of generating these test vectors hinders their use in radiation testing. Testing digital circuits in the industry is usually done nowadays using design for testability (DFT) techniques as they are very mature and can be relied on. DFT techniques include, but not limited to, ad-hoc technique, built-in self test (BIST), muxed D scan, clocked scan and enhanced scan. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Despite all these recommendations for DFT, radiation testing has not benefited from this reliable technology yet. Also, with the big variation in the DFT techniques, choosing the right technique is the bottleneck to achieve the best results for TID testing. In this thesis, a comprehensive comparison between different DFT techniques for TID testing of flash-based FPGAs is made to help designers choose the best suitable DFT technique depending on their application. The comparison includes muxed D scan technique, clocked scan technique and enhanced scan technique. The comparison is done using ISCAS-89 benchmarks circuits. Points of comparisons include FPGA resources utilization, difficulty of designs bring-up, added delay by DFT logic and robust testable paths in each technique

Design for testability of high-order OTA-C filters

Copyright © 2016 John Wiley & Sons, Ltd.A study of oscillation-based test for high-order Operational Transconductance Amplifier-C (OTA-C) filters is presented. The method is based on partition of a high-order filter into second-order filter functions. The opening Q-loop and adding positive feedback techniques are developed to convert the second-order filter section into a quadrature oscillator. These techniques are based on an open-loop configuration and an additional positive feedback configuration. Implementation of the two testability design methods for nth-order cascade, IFLF and leapfrog (LF) filters is presented, and the area overhead of the modified circuits is also discussed. The performances of the presented techniques are investigated. Fourth-order cascade, inverse follow-the-leader feedback (IFLF) and LF OTA-C filters were designed and simulated for analysis of fault coverage using the adding positive feedback method based on an analogue multiplexer. Simulation results show that the oscillation-based test method using positive feedback provides high fault coverage of around 97%, 96% and 95% for the cascade, IFLF and LF OTA-C filters, respectively. Copyright ÂPeer reviewe