2,575 research outputs found
Force control and collision avoidance strategies for kinematically redundant manipulators
The problem of position control of non-redundant manipulators was addressed during the initial stages of development of robotics in the 70's. In the 80's, extension of robotic applications to new non-conventional areas, such as space, underwater, hazardous environments, and microrobotics, brought new challenges for robotic researchers. Position control strategies failed in performing tasks that needed interaction with a robot's environment. On the other hand, non-redundant manipulators were unable to perform tasks that required dexterity comparable to that provided by the human arm. Also, imprecise dynamic modeling put severe restrictions on performance of control algorithms which were based on exact knowledge of dynamic parameters. These issues have therefore attracted a lot of attention in following three areas: force and compliant motion control, redundancy resolution, and adaptive control strategies. These areas have been addressed separately. However, there exists no unique frame work for an adaptive compliant motion control scheme for redundant manipulators which enjoys all the desirable characteristics of the methods that have been proposed for each individual area, e.g., the existing compliant motion control schemes are either not applicable to redundant manipulators or cannot take full advantage of the redundant degrees of freedom. In this thesis, the existing schemes in each of these three areas are reviewed. Based on the results of this review, a new redundancy resolution scheme at the acceleration level is proposed. The feasibility of this scheme is studied using simulations on a 3-DOF planar arm. This scheme is then extended to the 3-D workspace of a 7-DOF redundant manipulator. The performance of the extended scheme with respect to static and moving object collision avoidance and also joint limit avoidance is studied using both simulations and hardware experiments on REDIESTRO (a REdundant, Dextrous, Isotropically Enhanced, Seven Turning-pair RObot constructed in the Center for Intelligent Machines at McGill University). Based on this redundancy resolution scheme, an Augmented Hybrid Impedance Control (AHIC) scheme is proposed. The AHIC scheme provides a unified frame work for combining compliant motion control, redundancy resolution, and adaptive control in a single methodology. The feasibility of the proposed AHIC scheme is studied by computer simulations and experiments on REDIESTRO
Position control of redundant manipulators using an adaptive error-based control scheme
A Cartesian-space control scheme is developed to control the motion of kinematically redundant manipulators with 7 degrees of freedom (DOF). The control scheme consists mainly of proportional derivative (PD) controllers whose gains are adjusted by an adaptation law driven by the errors between the desired and actual trajectories. The adaptation law is derived using the concept of model reference adaptive control (MRAC) and Lyapunov direct method under the assumption that the manipulator performs non-compliant and slowly-varying motions. The developed control scheme is computationally efficient because its implementation does not require the computation of the manipulator dynamics. Computer simulation performed to evaluate the control scheme performance is presented and discussed
Development of advanced control schemes for telerobot manipulators
To study space applications of telerobotics, Goddard Space Flight Center (NASA) has recently built a testbed composed mainly of a pair of redundant slave arms having seven degrees of freedom and a master hand controller system. The mathematical developments required for the computerized simulation study and motion control of the slave arms are presented. The slave arm forward kinematic transformation is presented which is derived using the D-H notation and is then reduced to its most simplified form suitable for real-time control applications. The vector cross product method is then applied to obtain the slave arm Jacobian matrix. Using the developed forward kinematic transformation and quaternions representation of the slave arm end-effector orientation, computer simulation is conducted to evaluate the efficiency of the Jacobian in converting joint velocities into Cartesian velocities and to investigate the accuracy of the Jacobian pseudo-inverse for various sampling times. In addition, the equivalence between Cartesian velocities and quaternion is also verified using computer simulation. The motion control of the slave arm is examined. Three control schemes, the joint-space adaptive control scheme, the Cartesian adaptive control scheme, and the hybrid position/force control scheme are proposed for controlling the motion of the slave arm end-effector. Development of the Cartesian adaptive control scheme is presented and some preliminary results of the remaining control schemes are presented and discussed
Design of an adaptive controller for a telerobot manipulator
The design of a joint-space adaptive control scheme is presented for controlling the slave arm motion of a dual-arm telerobot system developed at Goddard Space Flight Center (GSFC) to study telerobotic operations in space. Each slave arm of the dual-arm system is a kinematically redundant manipulator with 7 degrees of freedom (DOF). Using the concept of model reference adaptive control (MRAC) and Lyapunov direct method, an adatation algorithm is derived which adjusts the PD controller gains of the control scheme. The development of the adaptive control scheme assumes that the slave arm motion is non-compliant and slowly-varying. The implementation of the derived control scheme does not need the computation of the manipulator dynamics, which makes the control scheme sufficiently fast for real-time applications. Computer simulation study performed for the 7-DOF slave arm shows that the developed control scheme can efficiently adapt to sudden change in payloads while tracking various test trajectories such as ramp or sinusoids with negligible position errors
Kinematics and control algorithm development and simulation for a redundant two-arm robotic manipulator system
An efficient approach to cartesian motion and force control of a 7 degree of freedom (DOF) manipulator is presented. It is based on extending the active stiffness controller to the 7 DOF case in general and use of an efficient version of the gradient projection technique for solving the inverse kinematics problem. Cooperative control is achieved through appropriate configuration of individual manipulator controllers. In addition, other aspects of trajectory generation using standard techniques are integrated into the controller. The method is then applied to a specific manipulator of interest (Robotics Research T-710). Simulation of the kinematics, dynamics, and control are provided in the context of several scenarios: one pertaining to a noncontact pick and place operation; one relating to contour following where contact is made between the manipulator and environment; and one pertaining to cooperative control
A Bio-Inspired Tensegrity Manipulator with Multi-DOF, Structurally Compliant Joints
Most traditional robotic mechanisms feature inelastic joints that are unable
to robustly handle large deformations and off-axis moments. As a result, the
applied loads are transferred rigidly throughout the entire structure. The
disadvantage of this approach is that the exerted leverage is magnified at each
subsequent joint possibly damaging the mechanism. In this paper, we present two
lightweight, elastic, bio-inspired tensegrity robotics arms which mitigate this
danger while improving their mechanism's functionality. Our solutions feature
modular tensegrity structures that function similarly to the human elbow and
the human shoulder when connected. Like their biological counterparts, the
proposed robotic joints are flexible and comply with unanticipated forces. Both
proposed structures have multiple passive degrees of freedom and four active
degrees of freedom (two from the shoulder and two from the elbow). The
structural advantages demonstrated by the joints in these manipulators
illustrate a solution to the fundamental issue of elegantly handling off-axis
compliance.Comment: IROS 201
Design of an Anthropomorphic, Compliant, and Lightweight Dual Arm for Aerial Manipulation
This paper presents an anthropomorphic, compliant and lightweight dual arm manipulator designed and developed for aerial manipulation applications with multi-rotor platforms. Each arm provides four degrees of freedom in a human-like kinematic configuration for end effector positioning: shoulder pitch, roll and yaw, and elbow pitch. The dual arm, weighting 1.3 kg in total, employs smart servo actuators and a customized and carefully designed aluminum frame structure manufactured by laser cut. The proposed
design reduces the manufacturing cost as no computer numerical control machined part is used. Mechanical joint compliance is provided in all the joints, introducing a compact spring-lever transmission mechanism between the servo shaft and the links, integrating a potentiometer for measuring the deflection of the joints.
The servo actuators are partially or fully isolated against impacts and overloads thanks to the ange bearings attached to the frame structure that support the rotation of the links and the deflection of the joints. This simple mechanism increases the robustness of the arms and safety in the physical interactions between the aerial
robot and the environment. The developed manipulator has been validated through different experiments in fixed base test-bench and in outdoor flight tests.Unión Europea H2020-ICT-2014- 644271Ministerio de Economía y Competitividad DPI2015-71524-RMinisterio de Economía y Competitividad DPI2017-89790-
Dynamic Modeling and Simulation of a Rotating Single Link Flexible Robotic Manipulator Subject to Quick Stops
Single link robotic manipulators are extensively used in industry and research operations. The main design requirement of such manipulators is to minimize link dynamic deflection and its active end vibrations, and obtain high position accuracy during its high speed motion. To achieve these requirements, accurate mathematical modeling and simulation of the initial design, to increase system stability and precision and to obtain very small amplitudes of vibration, should be considered. In this paper the modeling of such robotic arm with a rigid guide and a flexible extensible link subject to quick stops after each complete revolution is considered and its dynamical behavior analyzed. The extensible link which rotates with constant angular velocity has one end constrained to a predefined trajectory. The constrained trajectory allows trajectory control and obstacle avoidance for the active end of the robotic arm. The dynamic evolution of the system is investigated and the flexural response of the flexible link analyzed under the combined effect of clearance and flexibility.
- …