Comparative Analysis of NoCs for Two-Dimensional Versus Three-Dimensional SoCs Supporting Multiple Voltage and Frequency Islands

In many of today’s system-on-chip (SoC) designs, the cores are partitioned into multiple voltage and frequency islands (VFIs), and the global interconnect is implemented using a packetswitched network on chip (NoC). In such VFI-based designs, the benefits of 3-D integration in reducing the NoC power or delay are unclear, as a significant fraction of power is spent in link-level synchronization, and stacked designs may impose many synchronization boundaries. In this brief, we show the quantitative benefits of the 3-D technology on NoC power and delay values for such application-specific designs. We show a design flow for building application-specific NoCs for both 2-D and 3-D SoCs with multiple VFIs. We present a detailed case study of NoCs designed using the flow for a mobile platform. Our results show that power savings strongly depend on the number of VFIs used (up to 32% reduction). This motivates the need for an early architectural space exploration, as allowed by our flow. Our experiments also show that the reduction in delay is only marginal when moving from 2-D to 3-D systems (up to 11%), if both are designed efficiently

Design Methods and Tools for Application-Specific Predictable Networks-on-Chip

As the complexity of applications grows with each new generation, so does the demand for computation power. To satisfy the computation demands at manageable power levels, we see a shift in the design paradigm from single processor systems to Multiprocessor Systems-on-Chip (MPSoCs). MPSoCs leverage the parallelism in applications to increase the performance at the same power levels. To further improve the computation to power consumption ratio, MPSoCs for embedded applications are heterogeneous and integrate cores that are specialized to perform the different functionalities of the application. With technology scaling, wire power consumption is increasing compared to logic, making communication as expensive as computation. Therefore customizing the interconnect is necessary to achieve energy efficiency. Designing an optimal application specific Network-on-Chip (NoC), that meets application demands, requires the exploration of a large design space. Automatic design and optimization of the NoC is required in order to achieve fast design closure, especially for heterogeneous MPSoCs. To continue to meet the computation requirements of future applications new technologies are emerging. Three dimensional integration promises to increase the number of transistors by stacking multiple silicon layers. This will lead to an increase in the number of cores of the MPSoCs resulting in increased communication demands. To compensate for the increase in the wire delay in new technology nodes as well as to reduce the power consumption further, multi-synchronous design is becoming popular. With multiple clock signals, different parts of the MPSoC can be clocked at different frequencies according to the current demands of the application and can even be shutdown when they are not used at all. This further complicates the design of the NoC.Many applications require different levels of guarantee from the NoC in order to perform their functionality correctly. As communication traffic patterns become more complex, the performance of the NoC can no longer be predicted statically. Therefore designing the interconnect network requires that such guarantees are provided during the dynamic operation of the system which includes the interaction with major subsystems (i.e., main memory) and not just the interconnect itself. In this thesis, I present novel methods to design application-specific NoCs that meet performance demands, under the constraints of new technologies. To provide different levels of Quality of Service, I integrate methods to estimate the NoC performance during the design phase of the interconnect topology. I present methods and architectures for NoCs to efficiently access memory systems, in order to achieve predictable operation of the systems from the point of view of the communication as well as the bottleneck target devices. Therefore the main contribution of the thesis is twofold: scientific as I propose new algorithms to perform topology synthesis and engineering by presenting extensive experiments and architectures for NoC design

DVFS using clock scheduling for Multicore Systems-on-Chip and Networks-on-Chip

A modern System-on-Chip (SoC) contains processor cores, application-specific process- ing elements, memory, peripherals, all connected with a high-bandwidth and low-latency Network-on-Chip (NoC). The downside of such very high level of integration and con- nectivity is the high power consumption. In CMOS technology this is made of a dynamic and a static component. To reduce the dynamic component, Dynamic voltage and Fre- quency Scaling (DVFS) has been adopted. Although DVFS is very effective chip-wide, the power optimization of complex SoCs calls for a finer grain application of DVFS. Ideally all the main components of an SoC should be provided with a DVFS controller. An SoC with a DVFS controller per component with individual DC-DC converters and PLL/DLL circuits cannot scale in size to hundreds of components, which are in the research agenda. We present an alternative that will permit such scaling. It is possible to achieve results close to an optimum DVFS by hopping between few voltage levels and by an innovative application of clock-gating that we term as clock scheduling. We obtain an effective clock frequency by periodically killing some clock cycles of a master clock. We can apply voltage scaling for some of the periodic clock schedules which yield effective clock 1/2, 1/3, . . . By dithering between few voltages we obtain results close to an ideal DVFS system in simple pipelined circuits and in a complex example, a NoC’s switch. Again in the context of a NoC, we show how clock scheduling and voltage scaling can be automatically determined by means of a proportional-integral loop controller that keeps track of the network load. We describe in detail its implementation and all the circuit-level issues that we found. For a single switch, result shows an advantage of up to 2X over simple frequency scaling without voltage scaling. By providing each NoC’s switch with our simple DVFS controller, power saving at network level can be significantly more than what a a global DVFS controller can get. In a realistic scenario represented by network traces generated by video applications (MPEG, PIP, MWD, VoPD), we obtain an average power saving of 33%. To reduce static power, the Power-Gating (PG) technique is used and consists in switching- off power supply of unused blocks via pMOS headers or nMOS footers in series with such blocks. Even though research has been done in this field, the application of PG to NoCs has not been fully investigated. We show that it is possible to apply PG to the input buffers of a NoC switch. Their leakage power contributes about 40-50% of total NoC power, hence reducing such contribution is worthwhile. We partitioned buffers in banks and apply PG only to inactive banks. With our technique, it is possible to save about 40% in leakage power, without impact on performance

Exploration and Design of Power-Efficient Networked Many-Core Systems

Multiprocessing is a promising solution to meet the requirements of near future applications. To get full benefit from parallel processing, a manycore system needs efficient, on-chip communication architecture. Networkon- Chip (NoC) is a general purpose communication concept that offers highthroughput, reduced power consumption, and keeps complexity in check by a regular composition of basic building blocks. This thesis presents power efficient communication approaches for networked many-core systems. We address a range of issues being important for designing power-efficient manycore systems at two different levels: the network-level and the router-level. From the network-level point of view, exploiting state-of-the-art concepts such as Globally Asynchronous Locally Synchronous (GALS), Voltage/ Frequency Island (VFI), and 3D Networks-on-Chip approaches may be a solution to the excessive power consumption demanded by today’s and future many-core systems. To this end, a low-cost 3D NoC architecture, based on high-speed GALS-based vertical channels, is proposed to mitigate high peak temperatures, power densities, and area footprints of vertical interconnects in 3D ICs. To further exploit the beneficial feature of a negligible inter-layer distance of 3D ICs, we propose a novel hybridization scheme for inter-layer communication. In addition, an efficient adaptive routing algorithm is presented which enables congestion-aware and reliable communication for the hybridized NoC architecture. An integrated monitoring and management platform on top of this architecture is also developed in order to implement more scalable power optimization techniques. From the router-level perspective, four design styles for implementing power-efficient reconfigurable interfaces in VFI-based NoC systems are proposed. To enhance the utilization of virtual channel buffers and to manage their power consumption, a partial virtual channel sharing method for NoC routers is devised and implemented. Extensive experiments with synthetic and real benchmarks show significant power savings and mitigated hotspots with similar performance compared to latest NoC architectures. The thesis concludes that careful codesigned elements from different network levels enable considerable power savings for many-core systems.Siirretty Doriast

Embedded dynamic programming networks for networks-on-chip

PhD ThesisRelentless technology downscaling and recent technological advancements in three dimensional integrated circuit (3D-IC) provide a promising prospect to realize heterogeneous system-on-chip (SoC) and homogeneous chip multiprocessor (CMP) based on the networks-onchip (NoCs) paradigm with augmented scalability, modularity and performance. In many cases in such systems, scheduling and managing communication resources are the major design and implementation challenges instead of the computing resources. Past research efforts were mainly focused on complex design-time or simple heuristic run-time approaches to deal with the on-chip network resource management with only local or partial information about the network. This could yield poor communication resource utilizations and amortize the benefits of the emerging technologies and design methods. Thus, the provision for efficient run-time resource management in large-scale on-chip systems becomes critical. This thesis proposes a design methodology for a novel run-time resource management infrastructure that can be realized efficiently using a distributed architecture, which closely couples with the distributed NoC infrastructure. The proposed infrastructure exploits the global information and status of the network to optimize and manage the on-chip communication resources at run-time. There are four major contributions in this thesis. First, it presents a novel deadlock detection method that utilizes run-time transitive closure (TC) computation to discover the existence of deadlock-equivalence sets, which imply loops of requests in NoCs. This detection scheme, TC-network, guarantees the discovery of all true-deadlocks without false alarms in contrast to state-of-the-art approximation and heuristic approaches. Second, it investigates the advantages of implementing future on-chip systems using three dimensional (3D) integration and presents the design, fabrication and testing results of a TC-network implemented in a fully stacked three-layer 3D architecture using a through-silicon via (TSV) complementary metal-oxide semiconductor (CMOS) technology. Testing results demonstrate the effectiveness of such a TC-network for deadlock detection with minimal computational delay in a large-scale network. Third, it introduces an adaptive strategy to effectively diffuse heat throughout the three dimensional network-on-chip (3D-NoC) geometry. This strategy employs a dynamic programming technique to select and optimize the direction of data manoeuvre in NoC. It leads to a tool, which is based on the accurate HotSpot thermal model and SystemC cycle accurate model, to simulate the thermal system and evaluate the proposed approach. Fourth, it presents a new dynamic programming-based run-time thermal management (DPRTM) system, including reactive and proactive schemes, to effectively diffuse heat throughout NoC-based CMPs by routing packets through the coolest paths, when the temperature does not exceed chip’s thermal limit. When the thermal limit is exceeded, throttling is employed to mitigate heat in the chip and DPRTM changes its course to avoid throttled paths and to minimize the impact of throttling on chip performance. This thesis enables a new avenue to explore a novel run-time resource management infrastructure for NoCs, in which new methodologies and concepts are proposed to enhance the on-chip networks for future large-scale 3D integration.Iraqi Ministry of Higher Education and Scientific Research (MOHESR)

Network-on-Chip

Addresses the Challenges Associated with System-on-Chip Integration Network-on-Chip: The Next Generation of System-on-Chip Integration examines the current issues restricting chip-on-chip communication efficiency, and explores Network-on-chip (NoC), a promising alternative that equips designers with the capability to produce a scalable, reusable, and high-performance communication backbone by allowing for the integration of a large number of cores on a single system-on-chip (SoC). This book provides a basic overview of topics associated with NoC-based design: communication infrastructure design, communication methodology, evaluation framework, and mapping of applications onto NoC. It details the design and evaluation of different proposed NoC structures, low-power techniques, signal integrity and reliability issues, application mapping, testing, and future trends. Utilizing examples of chips that have been implemented in industry and academia, this text presents the full architectural design of components verified through implementation in industrial CAD tools. It describes NoC research and developments, incorporates theoretical proofs strengthening the analysis procedures, and includes algorithms used in NoC design and synthesis. In addition, it considers other upcoming NoC issues, such as low-power NoC design, signal integrity issues, NoC testing, reconfiguration, synthesis, and 3-D NoC design. This text comprises 12 chapters and covers: The evolution of NoC from SoC—its research and developmental challenges NoC protocols, elaborating flow control, available network topologies, routing mechanisms, fault tolerance, quality-of-service support, and the design of network interfaces The router design strategies followed in NoCs The evaluation mechanism of NoC architectures The application mapping strategies followed in NoCs Low-power design techniques specifically followed in NoCs The signal integrity and reliability issues of NoC The details of NoC testing strategies reported so far The problem of synthesizing application-specific NoCs Reconfigurable NoC design issues Direction of future research and development in the field of NoC Network-on-Chip: The Next Generation of System-on-Chip Integration covers the basic topics, technology, and future trends relevant to NoC-based design, and can be used by engineers, students, and researchers and other industry professionals interested in computer architecture, embedded systems, and parallel/distributed systems

Driving the Network-on-Chip Revolution to Remove the Interconnect Bottleneck in Nanoscale Multi-Processor Systems-on-Chip

The sustained demand for faster, more powerful chips has been met by the availability of chip manufacturing processes allowing for the integration of increasing numbers of computation units onto a single die. The resulting outcome, especially in the embedded domain, has often been called SYSTEM-ON-CHIP (SoC) or MULTI-PROCESSOR SYSTEM-ON-CHIP (MP-SoC). MPSoC design brings to the foreground a large number of challenges, one of the most prominent of which is the design of the chip interconnection. With a number of on-chip blocks presently ranging in the tens, and quickly approaching the hundreds, the novel issue of how to best provide on-chip communication resources is clearly felt. NETWORKS-ON-CHIPS (NoCs) are the most comprehensive and scalable answer to this design concern. By bringing large-scale networking concepts to the on-chip domain, they guarantee a structured answer to present and future communication requirements. The point-to-point connection and packet switching paradigms they involve are also of great help in minimizing wiring overhead and physical routing issues. However, as with any technology of recent inception, NoC design is still an evolving discipline. Several main areas of interest require deep investigation for NoCs to become viable solutions: • The design of the NoC architecture needs to strike the best tradeoff among performance, features and the tight area and power constraints of the onchip domain. • Simulation and verification infrastructure must be put in place to explore, validate and optimize the NoC performance. • NoCs offer a huge design space, thanks to their extreme customizability in terms of topology and architectural parameters. Design tools are needed to prune this space and pick the best solutions. • Even more so given their global, distributed nature, it is essential to evaluate the physical implementation of NoCs to evaluate their suitability for next-generation designs and their area and power costs. This dissertation performs a design space exploration of network-on-chip architectures, in order to point-out the trade-offs associated with the design of each individual network building blocks and with the design of network topology overall. The design space exploration is preceded by a comparative analysis of state-of-the-art interconnect fabrics with themselves and with early networkon- chip prototypes. The ultimate objective is to point out the key advantages that NoC realizations provide with respect to state-of-the-art communication infrastructures and to point out the challenges that lie ahead in order to make this new interconnect technology come true. Among these latter, technologyrelated challenges are emerging that call for dedicated design techniques at all levels of the design hierarchy. In particular, leakage power dissipation, containment of process variations and of their effects. The achievement of the above objectives was enabled by means of a NoC simulation environment for cycleaccurate modelling and simulation and by means of a back-end facility for the study of NoC physical implementation effects. Overall, all the results provided by this work have been validated on actual silicon layout

Doctor of Philosophy

dissertationCommunication surpasses computation as the power and performance bottleneck in forthcoming exascale processors. Scaling has made transistors cheap, but on-chip wires have grown more expensive, both in terms of latency as well as energy. Therefore, the need for low energy, high performance interconnects is highly pronounced, especially for long distance communication. In this work, we examine two aspects of the global signaling problem. The first part of the thesis focuses on a high bandwidth asynchronous signaling protocol for long distance communication. Asynchrony among intellectual property (IP) cores on a chip has become necessary in a System on Chip (SoC) environment. Traditional asynchronous handshaking protocol suffers from loss of throughput due to the added latency of sending the acknowledge signal back to the sender. We demonstrate a method that supports end-to-end communication across links with arbitrarily large latency, without limiting the bandwidth, so long as line variation can be reliably controlled. We also evaluate the energy and latency improvements as a result of the design choices made available by this protocol. The use of transmission lines as a physical interconnect medium shows promise for deep submicron technologies. In our evaluations, we notice a lower energy footprint, as well as vastly reduced wire latency for transmission line interconnects. We approach this problem from two sides. Using field solvers, we investigate the physical design choices to determine the optimal way to implement these lines for a given back-end-of-line (BEOL) stack. We also approach the problem from a system designer's viewpoint, looking at ways to optimize the lines for different performance targets. This work analyzes the advantages and pitfalls of implementing asynchronous channel protocols for communication over long distances. Finally, the innovations resulting from this work are applied to a network-on-chip design example and the resulting power-performance benefits are reported

High-level services for networks-on-chip

Future technology trends envision that next-generation Multiprocessors Systems-on- Chip (MPSoCs) will be composed of a combination of a large number of processing and storage elements interconnected by complex communication architectures. Communication and interconnection between these basic blocks play a role of crucial importance when the number of these elements increases. Enabling reliable communication channels between cores becomes therefore a challenge for system designers. Networks-on-Chip (NoCs) appeared as a strategy for connecting and managing the communication between several design elements and IP blocks, as required in complex Systems-on-Chip (SoCs). The topic can be considered as a multidisciplinary synthesis of multiprocessing, parallel computing, networking, and on- chip communication domains. Networks-on-Chip, in addition to standard communication services, can be employed for providing support for the implementation of system-level services. This dissertation will demonstrate how high-level services can be added to an MPSoC platform by embedding appropriate hardware/software support in the network interfaces (NIs) of the NoC. In this dissertation, the implementation of innovative modules acting in parallel with protocol translation and data transmission in NIs is proposed and evaluated. The modules can support the execution of the high-level services in the NoC at a relatively low cost in terms of area and energy consumption. Three types of services will be addressed and discussed: security, monitoring, and fault tolerance. With respect to the security aspect, this dissertation will discuss the implementation of an innovative data protection mechanism for detecting and preventing illegal accesses to protected memory blocks and/or memory mapped peripherals. The second aspect will be addressed by proposing the implementation of a monitoring system based on programmable multipurpose monitoring probes aimed at detecting NoC internal events and run-time characteristics. As last topic, new architectural solutions for the design of fault tolerant network interfaces will be presented and discussed