Low-Power Soft-Error-Robust Embedded SRAM

Soft errors are radiation-induced ionization events (induced by energetic particles like alpha particles, cosmic neutron, etc.) that cause transient errors in integrated circuits. The circuit can always recover from such errors as the underlying semiconductor material is not damaged and hence, they are called soft errors. In nanometer technologies, the reduced node capacitance and supply voltage coupled with high packing density and lack of masking mechanisms are primarily responsible for the increased susceptibility of SRAMs towards soft errors. Coupled with these are the process variations (effective length, width, and threshold voltage), which are prominent in scaled-down technologies. Typically, SRAM constitutes up to 90% of the die in microprocessors and SoCs (System-on-Chip). Hence, the soft errors in SRAMs pose a potential threat to the reliable operation of the system. In this work, a soft-error-robust eight-transistor SRAM cell (8T) is proposed to establish a balance between low power consumption and soft error robustness. Using metrics like access time, leakage power, and sensitivity to single event transients (SET), the proposed approach is evaluated. For the purpose of analysis and comparisons the results of 8T cell are compared with a standard 6T SRAM cell and the state-of-the-art soft-error-robust SRAM cells. Based on simulation results in a 65-nm commercial CMOS process, the 8T cell demonstrates higher immunity to SETs along with smaller area and comparable leakage power. A 32-kb array of 8T cells was fabricated in silicon. After functional verification of the test chip, a radiation test was conducted to evaluate the soft error robustness. As SRAM cells are scaled aggressively to increase the overall packing density, the smaller transistors exhibit higher degrees of process variation and mismatch, leading to larger offset voltages. For SRAM sense amplifiers, higher offset voltages lead to an increased likelihood of an incorrect decision. To address this issue, a sense amplifier capable of cancelling the input offset voltage is presented. The simulated and measured results in 180-nm technology show that the sense amplifier is capable of detecting a 4 mV differential input signal under dc and transient conditions. The proposed sense amplifier, when compared with a conventional sense amplifier, has a similar die area and a greatly reduced offset voltage. Additionally, a dual-input sense amplifier architecture is proposed with corroborating silicon results to show that it requires smaller differential input to evaluate correctly.1 yea

Digital Timing Control in SRAMs for Yield Enhancement and Graceful Aging Degradation

Embedded SRAMs can occupy the majority of the chip area in SOCs. The increase in process variation and aging degradation due to technology scaling can severely compromise the integrity of SRAM memory cells, hence resulting in cell failures. Enough cell failures in a memory can lead to it being rejected during initial testing, and hence decrease the manufacturing yield. Or, as a result of long-term applied stress, lead to in-field system failures. Certain types of cell failures can be mitigated through improved timing control. Post-fabrication programmable timing can allow for after-the-fact calibration of timing signals on a per die basis. This allows for a SRAM's timing signals to be generated based on the characteristics specific to the individual chip, thus allowing for an increase in yield and reduction in in-field system failures. In this thesis, a delay line based SRAM timing block with digitally programmable timing signals has been implemented in a 180 nm CMOS technology. Various timing-related cell failure mechanisms including: 1). Operational Read Failures, 2). Cell Stability Failures, and 3). Power Envelope Failures are investigated. Additionally, the major contributing factors for process variation and device aging degradation are discussed in the context of SRAMs. Simulations show that programmable timing can be used to reduce cell failure rates by over 50%

Unreliable Silicon: Circuit through System-Level Techniques for Mitigating the Adverse Effects of Process Variation, Device Degradation and Environmental Conditions.

Designing and manufacturing integrated circuits in advanced, highly-scaled processing technologies that meet stringent specification sets is an increasingly unreliable proposition. Dimensional processing variations, time and stress dependent device degradation and potentially varying environmental conditions exacerbate deviations in performance, power and even functionality of integrated circuits. This work explores a system-level adaptive design philosophy intended to mitigate the power and performance impact of unreliable silicon devices and presents enabling circuits for SRAM variation mitigation and in-situ measurement of device degradation in 130nm and 45nm processing technologies. An adaptation of RAZOR-based DVS designed for on-chip memory power reduction and reliability lifetime improvement enables the elimination of 250 mV of voltage margin in a 1.8V design, with up to 500 mV of reduction when allowing 5% of memory operations to use multiple cycles. A novel PID-controlled dynamic reliability management (DRM) system is presented, allowing user-specified circuit lifetime to be dynamically managed via dynamic voltage and frequency scaling. Peak performance improvement of 20-35% is achievable in typical processing systems by allowing brief periods of elevated voltage operation through the real-time DRM system, while minimizing voltage during non-critical periods of operation to maximize circuit lifetime. A probabilistic analysis of oxide breakdown using the percolation model indicates the need for 1000-2000 integrated in-situ sensors to achieve oxide lifetime prediction error at or under 10%. The conclusions from the oxide analysis are used to guide the design of a series of novel on-chip reliability monitoring circuits for use in a real-time DRM system. A 130nm in-situ oxide breakdown measurement sensor presented is the first published design of an oxide-breakdown oriented circuit and is compatible with standard-cell style automatic “place and route” design styles used in the majority of application specific integrated circuit designs. Measured results show increases in gate oxide leakage of 14-35% after accelerated stress testing. A second generation design of the on-chip oxide degradation sensor is presented that reduces stress mode power consumption by 111,785X over the initial design while providing an ideal 1:1 mapping of gate leakage to output frequency in extracted simulations.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/60701/1/ekarl_1.pd

Modeling and Mitigation of Soft Errors in Nanoscale SRAMs

Energetic particle (alpha particle, cosmic neutron, etc.) induced single event data upset or soft error has emerged as a key reliability concern in SRAMs in sub-100 nanometre technologies. Low operating voltage, small node capacitance, high packing density, and lack of error masking mechanisms are primarily responsible for the soft error susceptibility of SRAMs. In addition, since SRAM occupies the majority of die area in system-on-chips (SoCs) and microprocessors, different leakage reduction techniques, such as, supply voltage reduction, gated grounding, etc., are applied to SRAMs in order to limit the overall chip leakage. These leakage reduction techniques exponentially increase the soft error rate in SRAMs. The soft error rate is further accentuated by process variations, which are prominent in scaled-down technologies. In this research, we address these concerns and propose techniques to characterize and mitigate soft errors in nanoscale SRAMs. We develop a comprehensive analytical model of the critical charge, which is a key to assessing the soft error susceptibility of SRAMs. The model is based on the dynamic behaviour of the cell and a simple decoupling technique for the non-linearly coupled storage nodes. The model describes the critical charge in terms of NMOS and PMOS transistor parameters, cell supply voltage, and noise current parameters. Consequently, it enables characterizing the spread of critical charge due to process induced variations in these parameters and to manufacturing defects, such as, resistive contacts or vias. In addition, the model can estimate the improvement in critical charge when MIM capacitors are added to the cell in order to improve the soft error robustness. The model is validated by SPICE simulations (90nm CMOS) and radiation test. The critical charge calculated by the model is in good agreement with SPICE simulations with a maximum discrepancy of less than 5%. The soft error rate estimated by the model for low voltage (sub 0.8 V) operations is within 10% of the soft error rate measured in the radiation test. Therefore, the model can serve as a reliable alternative to time consuming SPICE simulations for optimizing the critical charge and hence the soft error rate at the design stage. In order to limit the soft error rate further, we propose an area-efficient multiword based error correction code (MECC) scheme. The MECC scheme combines four 32 bit data words to form a composite 128 bit ECC word and uses an optimized 4-input transmission-gate XOR logic. Thus MECC significantly reduces the area overhead for check-bit storage and the delay penalty for error correction. In addition, MECC interleaves two composite words in a row for limiting cosmic neutron induced multi-bit errors. The ground potentials of the composite words are controlled to minimize leakage power without compromising the read data stability. However, use of composite words involves a unique write operation where one data word is written while other three data words are read to update the check-bits. A power efficient word line signaling technique is developed to facilitate the write operation. A 64 kb SRAM macro with MECC is designed and fabricated in a commercial 90nm CMOS technology. Measurement results show that the SRAM consumes 534 μW at 100 MHz with a data latency of 3.3 ns for a single bit error correction. This translates into 82% per-bit energy saving and 8x speed improvement over recently reported multiword ECC schemes. Accelerated neutron radiation test carried out at TRIUMF in Vancouver confirms that the proposed MECC scheme can correct up to 85% of soft errors

Design of Variation-Tolerant Circuits for Nanometer CMOS Technology: Circuits and Architecture Co-Design

Aggressive scaling of CMOS technology in sub-90nm nodes has created huge challenges. Variations due to fundamental physical limits, such as random dopants fluctuation (RDF) and line edge roughness (LER) are increasing significantly with technology scaling. In addition, manufacturing tolerances in process technology are not scaling at the same pace as transistor's channel length due to process control limitations (e.g., sub-wavelength lithography). Therefore, within-die process variations worsen with successive technology generations. These variations have a strong impact on the maximum clock frequency and leakage power for any digital circuit, and can also result in functional yield losses in variation-sensitive digital circuits (such as SRAM). Moreover, in nanometer technologies, digital circuits show an increased sensitivity to process variations due to low-voltage operation requirements, which are aggravated by the strong demand for lower power consumption and cost while achieving higher performance and density. It is therefore not surprising that the International Technology Roadmap for Semiconductors (ITRS) lists variability as one of the most challenging obstacles for IC design in nanometer regime. To facilitate variation-tolerant design, we study the impact of random variations on the delay variability of a logic gate and derive simple and scalable statistical models to evaluate delay variations in the presence of within-die variations. This work provides new design insight and highlights the importance of accounting for the effect of input slew on delay variations, especially at lower supply voltages. The derived models are simple, scalable, bias dependent and only require the knowledge of easily measurable parameters. This makes them useful in early design exploration, circuit/architecture optimization as well as technology prediction (especially in low-power and low-voltage operation). The derived models are verified using Monte Carlo SPICE simulations using industrial 90nm technology. Random variations in nanometer technologies are considered one of the largest design considerations. This is especially true for SRAM, due to the large variations in bitcell characteristics. Typically, SRAM bitcells have the smallest device sizes on a chip. Therefore, they show the largest sensitivity to different sources of variations. With the drastic increase in memory densities, lower supply voltages and higher variations, statistical simulation methodologies become imperative to estimate memory yield and optimize performance and power. In this research, we present a methodology for statistical simulation of SRAM read access yield, which is tightly related to SRAM performance and power consumption. The proposed flow accounts for the impact of bitcell read current variation, sense amplifier offset distribution, timing window variation and leakage variation on functional yield. The methodology overcomes the pessimism existing in conventional worst-case design techniques that are used in SRAM design. The proposed statistical yield estimation methodology allows early yield prediction in the design cycle, which can be used to trade off performance and power requirements for SRAM. The methodology is verified using measured silicon yield data from a 1Mb memory fabricated in an industrial 45nm technology. Embedded SRAM dominates modern SoCs and there is a strong demand for SRAM with lower power consumption while achieving high performance and high density. However, in the presence of large process variations, SRAMs are expected to consume larger power to ensure correct read operation and meet yield targets. We propose a new architecture that significantly reduces array switching power for SRAM. The proposed architecture combines built-in self-test (BIST) and digitally controlled delay elements to reduce the wordline pulse width for memories while ensuring correct read operation; hence, reducing switching power. A new statistical simulation flow was developed to evaluate the power savings for the proposed architecture. Monte Carlo simulations using a 1Mb SRAM macro from an industrial 45nm technology was used to examine the power reduction achieved by the system. The proposed architecture can reduce the array switching power significantly and shows large power saving - especially as the chip level memory density increases. For a 48Mb memory density, a 27% reduction in array switching power can be achieved for a read access yield target of 95%. In addition, the proposed system can provide larger power saving as process variations increase, which makes it a very attractive solution for 45nm and below technologies. In addition to its impact on bitcell read current, the increase of local variations in nanometer technologies strongly affect SRAM cell stability. In this research, we propose a novel single supply voltage read assist technique to improve SRAM static noise margin (SNM). The proposed technique allows precharging different parts of the bitlines to VDD and GND and uses charge sharing to precisely control the bitline voltage, which improves the bitcell stability. In addition to improving SNM, the proposed technique also reduces memory access time. Moreover, it only requires one supply voltage, hence, eliminates the need of large area voltage shifters. The proposed technique has been implemented in the design of a 512kb memory fabricated in 45nm technology. Results show improvements in SNM and read operation window which confirms the effectiveness and robustness of this technique

Low-voltage embedded biomedical processor design

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2010.Cataloged from PDF version of thesis.Includes bibliographical references (p. 180-190).Advances in mobile electronics are fueling new possibilities in a variety of applications, one of which is ambulatory medical monitoring with body-worn or implanted sensors. Digital processors on such sensors serve to analyze signals in real-time and extract key features for transmission or storage. To support diverse and evolving applications, the processor should be flexible, and to extend sensor operating lifetime, the processor should be energy-efficient. This thesis focuses on architectures and circuits for low power biomedical signal processing. A general-purpose processor is extended with custom hardware accelerators to reduce the cycle count and energy for common tasks, including FIR and median filtering as well as computing FFTs and mathematical functions. Improvements to classic architectures are proposed to reduce power and improve versatility: an FFT accelerator demonstrates a new control scheme to reduce datapath switching activity, and a modified CORDIC engine features increased input range and decreased quantization error over conventional designs. At the system level, the addition of accelerators increases leakage power and bus loading; strategies to mitigate these costs are analyzed in this thesis. A key strategy for improving energy efficiency is to aggressively scale the power supply voltage according to application performance demands. However, increased sensitivity to variation at low voltages must be mitigated in logic and SRAM design. For logic circuits, a design flow and a hold time verification methodology addressing local variation are proposed and demonstrated in a 65nm microcontroller functioning at 0.3V. For SRAMs, a model for the weak-cell read current is presented for near-V supply voltages, and a self-timed scheme for reducing internal bus glitches is employed with low leakage overhead. The above techniques are demonstrated in a 0.5-1.OV biomedical signal processing platform in 0.13p-Lm CMOS. The use of accelerators for key signal processing enabled greater than 10x energy reduction in two complete EEG and EKG analysis applications, as compared to implementations on a conventional processor.by Joyce Y. S. Kwong.Ph.D

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Voltage drop tolerance by adaptive voltage scaling using clock-data compensation

Proyecto de Graduación (Maestría en Ingeniería en Electrónica) Instituto Tecnológico de Costa Rica, Escuela de Ingeniería Electrónica, 2019.El ruido de alta frecuencia en la red de alimentación compromete el rendimiento y la eficiencia energética de los sistemas electrónicos con microprocesadores, restringiendo la frecuencia máxima de operación de los sistemas y disminuyendo la confiabilidad de los dispositivos. La frecuencia máxima será determinada por la ruta de datos más crítica (la ruta de datos más lenta). De esta manera, es necesario configurar una banda de guarda para tolerar caídas de voltaje sin tener ningún problema de ejecución, pero sacrificando el rendimiento eléctrico. Este trabajo evalúa el impacto de la caída de voltaje en el rendimiento de los circuitos CMOS de alta densidad, estableciendo un conjunto de casos de prueba que contienen diferentes configuraciones de circuitos. Se desarrolló una técnica adaptable y escalable para mejorar la tolerancia a la caída de voltaje en los circuitos CMOS a través del escalado adaptativo, aprovechando el efecto de compensación de datos del reloj. La solución propuesta se validó aplicándola a diferentes casos de prueba en una tecnología FinFet-CMOS a nivel de simulación del diseño físico.High-frequency power supply noise compromises performance and energy efficiency of microprocessor-based products, restricting the maximum frequency of operation for electronic systems and decreasing device reliability. The maximum frequency is going to be determine by the most critical data path (the slowest data path). In this way, a guard band needs to be set in order to tolerate voltage drops without having any execution problem, but leading to a performance reduction. This work evaluates the impact of voltage drop in the performance of CMOS circuits by establishing a set of test cases containing different circuit configurations. An adaptive and scalable technique is proposed to enhance voltage drop tolerance in CMOS circuits through adaptive scaling, taking advantage of the clock-data compensation effect. The proposed solution is validated by applying it to different test cases in a FinFet CMOS technology at a post-layout simulation level

Low Power Memory/Memristor Devices and Systems

This reprint focusses on achieving low-power computation using memristive devices. The topic was designed as a convenient reference point: it contains a mix of techniques starting from the fundamental manufacturing of memristive devices all the way to applications such as physically unclonable functions, and also covers perspectives on, e.g., in-memory computing, which is inextricably linked with emerging memory devices such as memristors. Finally, the reprint contains a few articles representing how other communities (from typical CMOS design to photonics) are fighting on their own fronts in the quest towards low-power computation, as a comparison with the memristor literature. We hope that readers will enjoy discovering the articles within