Adaptive Harmonic Blocking Compensators.

This dissertation explores a new method of adaptive compensation and harmonic suppression in distribution systems. The compensator under development and investigation integrates a harmonic blocking compensator (HBC) with an adaptive balancing compensator (ABC) resulting in an adaptive harmonic blocking compensator (AHBC). Such a compensator can be used for compensating reactive power, for symmetrizing supply currents, for protecting the distribution system against load generated current harmonics and, consequently, the voltage harmonic distortion caused by non-linear loads. Harmonic blocking compensators are designed for compensating fixed loads, and they are not adaptive devices, while the adaptive capability of compensators is becoming more and more important. This dissertation investigates the possibility of the conversion of a HBC into an adaptive device. A HBC and an ABC are combined to form a new device which is referred to as an adaptive harmonic blocking compensator. A HBC provides the harmonic suppression. An ABC which contains three thyristor controlled susceptance circuits provides the variable susceptances needed for reactive and unbalanced power compensation. A digital signal processing system (DSPS) for three-phase quantities has been developed for the AHBC control. This DSPS consists of signal processing hardware and a control algorithm. The hardware includes transducers, a microcontroller and some associated circuits for signal processing. The control algorithm provides the thyristor firing angles calculated based on the current orthogonal decomposition method. The dissertation presents the fundamentals of AHBC operation and design, results of computer modeling using PSpice and experimental results obtained from a laboratory prototype

New trends in active filters for improving power quality

Since their basic compensation principles were proposed around 1970, active filters have been studied by many researchers and engineers aiming to put them into practical applications. Shunt active filters for harmonic compensation with or without reactive power compensation, flicker compensation or voltage regulation have been put on a commercial base in Japan, and their rating or capacity has ranged from 50 kVA to 60 MVA at present. In near future, the term of active filters will cover a much wider sense than that of active filters in the 1970s did. The function of active filters will be expanded from voltage flicker compensation or voltage regulation into power quality improvement for power distribution systems as the capacity of active filters becomes larger. This paper describes present states of the active filters based on state-of-the-art power electronics technology, and their future prospects toward the 21st century, including the personal view and expectation of the author</p

Improvement of resonant harmonic filter effectiveness in the presence of distribution voltage distortion

Resonant harmonic filters (RHFs), are the most common devices installed in distribution systems for reducing distortion caused by harmonic generating loads. When such filters are applied in systems with a distorted distribution voltage their effectiveness may decline drastically. This dissertation explores the causes of degradation of RHFs effectiveness and suggests methods of their improvement both by optimization algorithms and by modification of the filter structure. An optimization based design method is developed for the conventional RHF. It takes into consideration the interaction of the filter with the distribution system and provides a filter which gives the maximum effectiveness with respect to harmonic suppression. The results for the optimized filters, applied in some typical cases, are given, and the limits of effectiveness for a common application are explored. For cases where the conventional RHF cannot be applied due to low effectiveness, a resonant harmonic suppressor, referred to as a RHF with line inductor, is investigated. It is formed by the addition of a line inductor to a conventional RHF, and it has a higher effectiveness in the presence distribution voltage distortion. A similar method of optimization based design is developed and evaluated for the RHF with line inductor as for the conventional RHF. Also, the limits of its effectiveness are explored. One major disadvantage of the RHF with line inductor is the load voltage reduction due to the additional impedance between the distribution system and load. For loads with variable reactive power, the voltage drop across the line inductor may reach an unacceptable level. Also, the fluctuation of the load voltage could increase. In order to reduce these effects, an adaptive capability with respect to load reactive power compensation is added to the filter. Such a filter, referred to as a semi-adaptive RHF, is obtained when a RHF is combined with a thyristor switched inductor (TSI). The addition of the TSI also increases flexibility in the design of the filter with respect to the line inductor’s value. Design aspects of the semi-adaptive RHF are explored and simulation results are presented

Optimal sizing of C-type passive filters under non-sinusoidal conditions

In the literature, much attention has been focused on power system harmonics. One of its important effects is degradation of the load power factor. In this article, a C-type filter is used for reducing harmonic distortion, improving system performance, and compensating reactive power in order to improve the load power factor while taking into account economic considerations. Optimal sizing of the C-type filter parameters based on maximization of the load power factor as an objective function is determined. The total installation cost of the C-type filter and that of the conventional shunt (single-tuned) passive filter are comparatively evaluated. Background voltage and load current harmonics are taken into account. Recommendations defined in IEEE standards 519-1992 and 18-2002 are taken as the main constraints in this study. The presented design is tested using four numerical cases taken from previous publications, and the proposed filter results are compared with those of other published techniques. The results validate that the performance of the C-type passive filter as a low-pass filter is acceptable, especially in the case of lower short-circuit capacity systems. The C-type filter may achieve the same power factor with a lower total installation cost than a single-tuned passive filter

Trends in active power line conditioners

Active power line conditioners, which are classified into shunt and series ones, have been studied with the focus on their practical installation in industrial power systems. In 1986, a combined system of a shunt active conditioner of rating 900 kVA and a shunt passive filter of rating 6600 kVA was practically installed to suppress the harmonics produced by a large capacity cycloconverter for steel mill drives. More than one hundred shunt active conditioners have been operating properly in Japan. The largest one is 20 MVA, which was developed for flicker compensation for an arc furnace with the help of a shunt passive filter of 20 MVA. In this paper, the term of “active power line conditioners” is used instead of that of “active power filters” because active power line conditioners would cover a wider sense than active power filters. The primary intent of this paper is to present trends in active power line conditioners using PWM inverters, paying attention to practical applications</p

New hybrid active power filter for harmonic current suppression and reactive power compensation

In the case of undistorted and balanced grid voltages, low ratio shunt Active Power Filters (APFs) can give unity power factors and achieve current harmonic cancellation. However, this is not possible when source voltages are distorted and unbalanced. In this study, the cost-effective hybrid active power filter (HAPF) topology for satisfying the requirements of harmonic-current suppression and non-active power compensation for industry is presented. An effective strategy is developed to observe the effect of the placement of power capacitors and LC filters with the shunt active power filter. A new method for alleviating the negative effects of a non-ideal grid voltage is proposed that uses a self-tuning filter algorithm with instantaneous reactive power theory. The real-time control of the studied system was achieved with a field programmable gate array (FPGA) architecture, which was developed using the OPAL-RT system. The performance results of the proposed HAPF system is tested and presented under non-ideal supply voltage conditions

New trends in active filters for power conditioning

Attention has been paid to active filters for power conditioning which provide the following multifunctions: reactive power compensation; harmonic compensation; flicker/imbalance compensation; and voltage regulation. Active filters in a range of 50 kVA-60 MVA have been practically installed in Japan. In the near future, the term “active filters” will have a much wider meaning than it did in the 1970s. For instance, active filters intended for harmonic solutions are expanding their functions from harmonic compensation of nonlinear loads into harmonic isolation between utilities and consumers, and harmonic damping throughout power distribution systems. This paper presents the present status of active filters based on state-of-the-art power electronics technology, and their future prospects and directions toward the 21st Century, including the personal views and expectations of the author</p

Distributed photovoltaic systems: Utility interface issues and their present status

Major technical issues involving the integration of distributed photovoltaics (PV) into electric utility systems are defined and their impacts are described quantitatively. An extensive literature search, interviews, and analysis yielded information about the work in progress and highlighted problem areas in which additional work and research are needed. The findings from the literature search were used to determine whether satisfactory solutions to the problems exist or whether satisfactory approaches to a solution are underway. It was discovered that very few standards, specifications, or guidelines currently exist that will aid industry in integrating PV into the utility system. Specific areas of concern identified are: (1) protection, (2) stability, (3) system unbalance, (4) voltage regulation and reactive power requirements, (5) harmonics, (6) utility operations, (7) safety, (8) metering, and (9) distribution system planning and design